【国外标准】 Standard Test Method for Cashmere Coarse-Hair Content in Cashmere
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
5.1 This test method may be used for determining compliance with a specification for maximum cashmere coarse-hair content and is required to be used for determining compliance with Specification D2817.5.1.1 In case of a dispute arising from differences in reported test results when using Test Method D2816 for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing is begun. If a bias is found, either its cause must be found and corrected or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.5.2 When the product being tested has a cashmere coarse-hair content that departs significantly either way from the specified amount, the sequential test procedure described herein will result in a substantial reduction in the number of observations required for a decision at the stated level of confidence. On the other hand, when the product being tested has a cashmere coarse-hair content that approaches the specified amount, the sequential procedure ensures that the necessary increased number of observations shall be made to secure a correct decision at the stated level of confidence.1.1 This test method covers a sequential procedure for determining whether or not the cashmere coarse-hair content of a sample exceeds a specified value.NOTE 1: For the maximum allowable cashmere coarse-hair content in cashmere, refer to Specification D2817.NOTE 2: For the quantitative analysis of cashmere hair and blends of cashmere hair and other fibers, refer to Test Methods D629.1.2 This test method is applicable only to cashmere hair in the form of roving, yarn, or fabric, and to the cashmere hair content of blends with other fibers, where the expected cashmere coarse-hair content is not more than five mass percent (see Footnote C of Table 1). For greater expected mass percentages of cashmere coarse-hair, see Test Methods D629.The data from these studies are on file with the Secretary of Subcommittee D13.13, Committee D13 of ASTM.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D2816-18
标准名称:
Standard Test Method for Cashmere Coarse-Hair Content in Cashmere
英文名称:
Standard Test Method for Cashmere Coarse-Hair Content in Cashmere标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard
- KS M ISO 4259-4 석유 및 관련 제품 — 측정 방법과 결과의 정밀도 — 제4부: 개별 실험실에서 표준 시험방법의 실행에 대한 ‘통계적 관리’ 상태를 확인하기 위한 통계적 관리도의 사용
- KS C IEC 61340-4-6 정전기학 — 제4-6부: 구체적 적용 분야에 대한 표준 시험방법 — 손목접지대
- KS C IEC 61340-4-7 정전기학 — 제4-7부: 구체적 적용 분야에 대한 표준 시험방법 — 이온화
- KS C IEC 61340-4-8 정전기학 — 제4-8부: 구체적 적용 분야에 대한 표준 시험방법 — ESD 차폐성 — 봉투
- 24/30485973 DC standard