Update No. 1 was published as notification that this is now a National Standard of Canada This PDF includes Update No. 1 Z241.0-03 Definitions and General Safety Requirements for Park Model Trailers 1. Scope This Standard provides the definition o

定价： 1911元 / 折扣价： 1625 元

定价： 3504元 / 折扣价： 2979 元

This specification covers the requirements for non-heat treated carbon steel machine screws. Steel for the machine screws shall be made by open-hearth, basic-oxygen, or electric-furnace process and the screws shall be manufactured by cold forming, thread rolling, and stress-relieve annealing. Heat and product analysis shall be performed to determine the chemical composition of the specimen conforming to the requirements for carbon, phosphorus, and sulfur. Specimens shall be subjected to mechanical tests to verify conformance to the mechanical property requirements such as tensile strength, Rockwell hardness, and ductility.1.1 This specification covers the requirements for non-heat treated carbon steel machine screws with nominal diameters of No. 0000 through ¾ in. having a minimum ultimate tensile strength of 60 000 psi.1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

定价： 0元 / 折扣价： 0 元

定价： 605元 / 折扣价： 515 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 1365元 / 折扣价： 1161 元

定价： 1820元 / 折扣价： 1547 元

This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, and studs, including heat-treated machine screws, tapping screws, and sems. Types of surface discontinuities are: crack; burst; seam; fold; thread lap; void; tool marks; and gouge and nick. These surface discontinuities shall be inspected in accordance with the specified requirements.1.1 This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of bolts, screws, studs, and rivets including heat-treated machine screws, tapping screws, and sems (the washers of screw-washer assemblies are excluded). This specification covers metric series products with nominal diameters of 4 mm and larger and with specified minimum tensile strengths of 420 MPa and higher; and inch series products with nominal diameters of No. 5 (0.1250 in.) and larger and with specified minimum tensile strengths of 60 000 psi and higher.1.2 When the engineering requirements of the application necessitate control of surface discontinuities on bolts, screws, studs, or rivets, the purchaser shall specify conformance to ASTM Specification F788/F788M, in the original inquiry and purchase order.1.2.1 When the engineering requirements of the application necessitate that surface discontinuities on bolts, screws, studs, and rivets be controlled within limits closer than those specified in this specification, the purchaser shall specify the applicable limits in the original inquiry and purchase order.1.3 The allowable limits established in this specification for metric bolts, screws, and studs with nominal diameters from 4 to 24 mm inclusive, are essentially identical with requirements given in ISO 6157/I. There are no ISO standards for surface discontinuities on any inch-series products, or for rivets.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 1333元 / 折扣价： 1134 元 加购物车

This specification establishes allowable limits for the various types of surface discontinuities such as cracks that may occur during the manufacture and processing of metric-series nuts and inch-series nuts. The different types of surface discontinuities and allowable limits are presented in details. The nuts shall be inspected for surface discontinuities to meet the requirements prescribed. Cone proof load test shall be performed to meet the requirements prescribed.1.1 This specification establishes allowable limits for the various types of surface discontinuities that may occur during the manufacture and processing of metric-series nuts with nominal diameters 5 mm and larger and inch-series nuts with nominal diameters 1/4 in. and larger.1.2 The values stated in either SI (metric) or inch-pound units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.3 When the engineering requirements of the application necessitate control of surface discontinuities on nuts, the purchaser shall specify conformance to this ASTM specification in the original inquiry and purchase order.1.3.1 When the engineering requirements of the application necessitate that surface discontinuities on nuts be controlled within limits closer than those specified in this specification, the purchaser shall specify the applicable limits in the original inquiry and purchase order.1.4 The allowable limits established in this specification for metric nuts, with nominal diameters 5 to 24 mm inclusive, are essentially identical with requirements given in ISO/DIS 6157/II. There are no ISO standards for surface discontinuities on metric-series nuts with nominal diameters larger than 24 mm or on any inch-series nuts.1.5 The following precautionary caveat pertains only to the test method portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

Update #1 was published as notification that this is now a National Standard of Canada This PDF includes Update #1 Z341.1-02 Reservoir Storage 1 Scope 1.1 This Standard sets out the minimum requirements for the design, construction, operation,

定价： 1593元 / 折扣价： 1355 元

定价： 156元 / 折扣价： 133 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 2730元 / 折扣价： 2321 元

定价： 3140元 / 折扣价： 2669 元