1.1 This specification covers the requirements for nonferrous socket set screws sizes 0.125 (#5) through 2.000 in., square head set screws sizes 0.190 (#10) through 1.500 in., and slotted headless set screws 0.125 (#5) through 0.750 in. in diameter manufactured from a number of nonferrous alloys in use in the marine industry and the U.S. Navy subject to seawater wetting and salt atmosphere but that also may be used in other applications. It is recommended that copper-based alloys not be used in attempting to prevent mechanical components from rotating, such as locking shafts, because of the low hardness of the alloys. Some alloys or sizes or both of set screws may not be readily available. Manufacturers or suppliers should be contacted before design development or anticipated procurement.1.2 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.NOTE 1: A complete metric companion to Specification F3042 will be developed—F3042M; therefore, no metric equivalents are shown in this specification.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws. The screws shall be fabricated from alloy steel made to fine grain practice. The chemical composition of the screw material shall conform to the heat analysis specified. Hardness, tensile strength, yield strength, elongation, and area reduction shall be tested to meet the requirements prescribed.1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) 0.060 through 0.625 thread sizes, flat countersunk (SFHCS) 0.060 through 1.5 thread sizes and low (SLHCS) 0.1120 through 0.625 thread sizes head cap screws having material properties for high-strength requirements.1.2 Fasteners meeting this specification are intended for shear-type applications and have tensile requirements ranging from 122 to 150 ksi.1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.4 The hazard statement applies only to the test method section, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws. The screws shall be fabricated from alloy steel made to fine grain practice. The chemical composition of the screw material shall conform to the heat analysis specified. Hardness, tensile strength, yield strength, elongation, and area reduction shall be tested to meet the requirements prescribed.1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws M3 through M20 thread sizes having material properties of ISO 898/1 Property Class 12.9.1.2 Fasteners meeting this specification are intended for shear type applications and have tensile requirements equivalent to ISO 898/1 Property Class 10.9.1.3 The hazard statement pertains only to the test method section, Section 11 of this specification. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers stainless steel socket head cap screws (SHCS) intended for use in applications requiring general corrosion resistance. Two groups of stainless steel alloys are covered, austenitic Grade A1 and martensitic Grade C1. Four property classes are covered: austenitic A1-50 in an annealed condition; austenitic A1-55 in a cold worked condition; austenitic A1-70 in a cold worked condition, and martensitic C1-110 in a heat treated condition. Materials shall be tested and the individual grades shall conform to forging; threads; heat treatment; chemical composition; mechanical properties such as thread diameter, tensile strength, yield strength, elongation, core hardness (Vickers and Rockwell); and corrosion resistance values. Workmanship, finish, and appearance are also detailed.1.1 This specification covers the chemical and mechanical requirements for stainless steel inch socket head cap screw (SHCS) with nominal thread 0.060 through 1.500 in. and intended for use in applications requiring general corrosion resistance.1.2 Three groups of stainless steel alloys are covered, austenitic Group 1 and 2 and martensitic Group 5.1.3 Four property conditions are covered: austenitic Alloy Groups 1 and 2 in an annealed condition (AF) at 85 ksi maximum, in two cold worked conditions (CW) at 80 ksi minimum, (CW1) at 102 ksi minimum, and martensitic Alloy Group 5 in a heat treated condition (HT) at 160 ksi minimum.1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.5 The following precautionary caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 702元 / 折扣价： 597 元 加购物车

This specification covers stainless steel metric socket head cap screws (SHCS) intended for use in applications requiring general corrosion resistance. Two groups of stainless steel alloys are covered, austenitic Grade A1 and martensitic Grade C1. Four property classes are covered: austenitic A1-50 in an annealed condition; austenitic A1-55 in a cold worked condition; austenitic A1-70 in a cold worked condition, and martensitic C1-110 in a heat treated condition. Materials shall be tested and the individual grades shall conform to forging; threads; heat treatment; chemical composition; mechanical properties such as thread diameter, tensile strength, yield strength, elongation, core hardness (Vickers and Rockwell); and corrosion resistance values. Workmanship, finish, and appearance are also detailed.1.1 This specification covers the chemical and mechanical requirements for stainless steel metric socket head cap screws (SHCS) with nominal thread M1.6 through M36 and intended for use in applications requiring general corrosion resistance.1.2 Two groups of stainless steel alloys are covered, austenitic Grade A1 and martensitic Grade C1.1.3 Four property classes are covered: austenitic A1-50 in an annealed condition at 585 MPa maximum; austenitic A1–55 in a cold worked condition at 550 MPa minimum; austenitic A1-70 in a cold worked condition at 700 MPa minimum, and martensitic C1-110 in a heat treated condition at 1100 MPa minimum.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This hazard statement pertains only to Section 13, Test Methods: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

This specification covers the requirements for quenched and tempered alloy steel socket-head cap screws. The screws shall be fabricated from steel made to fine grain practice and shall be alloy steel conforming to the chemical composition specified. Different tests shall be conducted in order to determine the following mechanical properties of screws: tensile or wedge strength, proof load, yield strength, elongation, Rockwell hardness, and Vickers hardness.1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 0.060 through 4 in. in diameter where high strength is required.1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.3 The following hazard caveat pertains only to the test method portions, Sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for quenched and tempered alloy steel socket-head cap screws. The screws shall be fabricated from steel made to fine grain practice and shall be alloy steel conforming to the chemical composition specified. Different tests shall be conducted in order to determine the following mechanical properties of screws: tensile or wedge strength, proof load, yield strength, elongation, Rockwell hardness, and Vickers hardness.1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket-head cap screws, 1.6 mm through 48 mm in diameter having a minimum ultimate tensile strength of 1220 MPa.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.Note 1—This specification is the metric companion of Specification A574.1.3 The following hazard caveat pertains only to the test method portions, sections 5.1, 5.6, 8, and 12, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers the chemical and mechanical requirements for stainless steel metric hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws with nominal thread M 3 through M 20 intended for use in applications requiring general corrosion resistance. These steels are designated into three classes: Austenitic Class A 1-50 in an annealed condition, Austenitic Class A1-55 in a cold worked condition, and Austenitic Class A 1-70 in a cold worked condition. The austenitic stainless steel socket screw shall be designated F879M A1-50, F879M A1–55, or F 879M A1-70. Screws shall be formed by upsetting or extruding, or both. Also, these screws shall be roll threaded. Austenitic alloys ClassA 1-50 screws, following manufacture, shall be annealed by heating to a certain temperature to obtain maximum corrosion resistance and minimum permeability. The screws shall be held for a sufficient time at temperature, then cooled at a rate sufficient to prevent precipitation of the carbide and provide the properties specified. Different tests shall be conducted in order to determine the following mechanical properties of screws: tensile strength, minimum extension, yield strength, elongation, Vickers hardness, and Rockwell hardness.1.1 This specification covers the chemical and mechanical requirements for stainless steel inch hexagon socket button (SBHCS), flat countersunk (SFHCS) head cap screws with nominal thread 0.060 through 0.625 in. and low head (SLHCS) cap screws with nominal thread 0.112 through 0.625 in. intended for use in applications requiring general corrosion resistance.1.2 Two groups of austenitic stainless steel alloys and three conditions are covered. See Table 1 and Table 2.1.3 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.4 The following precautionary caveat pertains only to the test method portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the chemical and mechanical requirements for stainless steel metric hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws with nominal thread M 3 through M 20 intended for use in applications requiring general corrosion resistance. These steels are designated into three classes: Austenitic Class A 1-50 in an annealed condition, Austenitic Class A1-55 in a cold worked condition, and Austenitic Class A 1-70 in a cold worked condition. The austenitic stainless steel socket screw shall be designated F879M A1-50, F879M A1–55, or F 879M A1-70. Screws shall be formed by upsetting or extruding, or both. Also, these screws shall be roll threaded. Austenitic alloys ClassA 1-50 screws, following manufacture, shall be annealed by heating to a certain temperature to obtain maximum corrosion resistance and minimum permeability. The screws shall be held for a sufficient time at temperature, then cooled at a rate sufficient to prevent precipitation of the carbide and provide the properties specified. Different tests shall be conducted in order to determine the following mechanical properties of screws: tensile strength, minimum extension, yield strength, elongation, Vickers hardness, and Rockwell hardness.1.1 This specification covers the chemical and mechanical requirements for stainless steel metric hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws with nominal thread M 3 through M 20 intended for use in applications requiring general corrosion resistance.1.2 The following three property classes are covered:1.2.1 Austenitic Class A1-50 in an annealed condition at 585 MPa maximum,1.2.2 Austenitic Class A1–55 in a cold worked condition at 550 MPa minimum, and1.2.3 Austenitic Class A1-70 in a cold-worked condition at 700 MPa minimum.1.3 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 The following hazard caveat pertains only to Section 12, Test Methods: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers the requirements for austenitic grade stainless steel socket set screws (SSS), sizes M1.6 through M24, having property classes A1-50 and A1-70. The analysis of the screw material shall conform to the chemical composition specified. Socket set screw shall be subjected to torque test, Vickers hardness test, and corrosion resistance test to meet the requirements prescribed.1.1 This specification covers the requirements for austenitic grade stainless steel socket-set screws (SSS) sizes 0.060 through 1.000 in. square head set screws (SHSS) sizes 0.190 through 1.500 in., and slotted headless set screws (HSS) 0.060 through 0.750 in., in two conditions, AF and CW.1.2 Units—The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.NOTE 1: A complete metric companion to Specification F880 has been developed—F880M; therefore, no metric equivalents are shown in this specification.1.3 The following hazards caveat pertains only to Test Method Section, Section 12 of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the requirements for austenitic grade stainless steel socket set screws (SSS), sizes M1.6 through M24, having property classes A1-50 and A1-70. The analysis of the screw material shall conform to the chemical composition specified. Socket set screw shall be subjected to torque test, Vickers hardness test, and corrosion resistance test to meet the requirements prescribed.1.1 This specification covers the requirements for austenitic grade stainless steel socket set screws (SSS), sizes M1.6 through M24, having Property Classes A1-50 and A1-70.1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.NOTE 1: This specification is the metric companion of Specification F880.1.3 The following hazard caveat pertains only to Section 11, the Test Method Section: This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元