定价： 605元 / 折扣价： 515 元 加购物车

定价： 1177元 / 折扣价： 1001 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 689元 / 折扣价： 586 元 加购物车

定价： 689元 / 折扣价： 586 元

定价： 819元 / 折扣价： 697 元

定价： 345元 / 折扣价： 294 元

5.1 Threshold of Capture and Containment—This test method describes flow visualization techniques that are used to determine the threshold of capture and containment (C&C) for idle and specified heavy cooking conditions. The threshold of C&C can be used to estimate minimum flow rates for hood/appliance systems.5.2 Parametric Studies—This test method also can be used to conduct parametric studies of alternative configurations of hoods, appliances, and replacement air systems. In general, these studies are conducted by holding constant all configuration and operational variables except the variable of interest. This test method, therefore, can be used to evaluate the following:5.2.1 The overall system performance with various appliances, while holding the hood and replacement air system characteristics constant.5.2.2 Entire hoods or characteristics of a single hood, such as end panels, can be varied with appliances and replacement air constant.5.2.3 Replacement air characteristics, such as make-up air location, direction, and volume, can be varied with constant appliance and hood variables.1.1 Characterization of capture and containment performance of hood, appliance(s), and replacement air system during cooking and non-cooking conditions (idle):1.2 Parametric evaluation of operational or design variations in appliances, hoods, or replacement air configurations.1.3 The test method to determine heat gain to space from commercial kitchen ventilation/appliance systems has been re-designated as Test Method F2474.1.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This PDF includes GI #2. 1. Scope 1.1 This Standard defines the requirements for performance, installation and application, and performance verification of mechanical ventilation systems. This Standard applies to systems that are capable of providi

定价： 774元 / 折扣价： 658 元

定价： 481元 / 折扣价： 409 元 加购物车

This specification covers the requirements and corresponding test methods for manufactured polymeric materials used to provide a rainscreen function, a means for the drainage of liquid moisture and the ventilation of vapor moisture that enters an above-grade exterior wall assembly. Rainscreen materials that conform to this specification are intended to be used behind exterior cladding products and to cover the entire wall area that is designed to provide a rainscreen function to resist water infiltration. Three types of rainscreen materials are addressed: Type A (entangled mesh materials), Type B (formed/textured sheet material), and Type C (formed battens). This specification also covers descriptions of the materials and material composition; material properties and material performance requirements; specimen preparation; reporting requirements; marking and labeling; and packaging and package marking. A table presents the requirements for ventilation/airflow, drainage, thickness, compression, strength, UV exposure, heat aging, mold/fungal growth, and water exposure.1.1 This specification is applicable to manufactured polymeric materials used to provide a rainscreen function, a means for the drainage of liquid moisture and the ventilation of vapor moisture that enters an above-grade exterior wall assembly. Rainscreen materials that comply with this specification are intended to be used behind exterior cladding products and intended to cover one hundred percent (100 %) of the wall area that is designed to provide a rainscreen function to resist water infiltration.1.2 This specification addresses the following types of rainscreen materials:1.2.1 Type A—entangled mesh materials.1.2.2 Type B—formed/textured sheet material.1.2.3 Type C—formed battens.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车