定价： 345元 / 折扣价： 294 元

定价： 156元 / 折扣价： 133 元 加购物车

5.1 Upon mutual agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.5.2 It is recognized that for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.5.2.1 In such cases, any references to the specification shall specify that: This fabric meets ASTM Specification D4154 except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers knitted and woven fabrics comprised of any textile fiber or mixture of fibers used in men's and boy's beachwear and sports shirts.1.2 This performance specification is not applicable to knitted and woven fabrics used for interlining and swimwear.1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method is considered satisfactory for acceptance testing of commercial shipments.5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results were obtained, and are randomly assigned in equal numbers to each laboratory for testing. Other fabrics with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.5.2 Individual rolls are normally accepted or rejected on the basis of the maximum amount of bow or skew in a specific roll of fabric. The average bow or skew in a roll or lot or the range of bow or skew in a roll may be determined but are not normally used in the trade for acceptance or rejection.5.3 Bow or skew can be induced during fabric manufacturing, dyeing, tentering, finishing, or other operations where a potential exists for uneven distribution of tensions across the fabric width. Bow and skew are more visually displeasing in colored, patterned fabrics such as plaids and horizontal stripes rather than in solid colors because the contrast makes the distortion more prominent. These defects may cause sewing problems in such fabrics and draping problems in finished products. In some cases, a specified amount of skew is needed, for example, to prevent twisting of pant legs made of twill fabric. Matching plaids from distorted patterns may create serious problems for the garment manufacturer or home sewer. Wavy or sharp breaks in the bow line are more detrimental to the appearance of small parts of a garment (such as collars, pockets, and so forth) than a gradual slope from a straight line.5.3.1 Automotive interior textiles used for seat bolsters, cushions, headrests and door panels may be susceptible to bow and skew, especially when visually patterned fabrics are joined or mated to a straight edge surface.1.1 This test method covers the determination of bow and skew of filling yarns in woven fabrics and the courses in knitted fabrics.1.2 This test method can also be used to measure the bow and skew of printed geometric designs.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 Upon mutual agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4156 except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers knitted fabrics comprised of any textile fiber or mixture of fibers, used in women's and girl's sportswear.1.2 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

Knitted fabrics are known to exhibit inherent variations in properties. This specification lists the tolerances for each property deemed acceptable in the trade.These tolerances can be used to determine if knitted fabrics meet specifications for properties, and provide a guide in case of dispute.Tolerances agreed upon between the purchaser and the seller shall take precedence over those listed in this specification.AbstractThis specification details the test methods and tolerances applicable to the following properties of knitted fabrics: yield; mass (weight); width; length; fabric count; bursting strength; moisture regain; thickness; extractable matter; and fiber composition. These tolerances are applicable to knitted fabrics of all types, such as warp knits, weft knits, flat bed knits, and so forth.1.1 This specification covers test methods and tolerances applicable to the following properties of knitted fabrics: yield, mass (weight), width, length, fabric count, bursting strength, moisture regain, thickness, extractable matter, and fiber composition.1.2 These tolerances are applicable to knitted fabrics of all types, such as warp knits, weft knits, flat bed knits, and so forth.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

5.1 Fabric stretch and fabric growth are useful in selection of fabrics that are required to stretch, but also recover to their original shape.5.1.1 In apparel, fabric stretch can be caused by a variety of factors. A momentary stress occurs when a fabric is required to accommodate movement, such as sportswear and other loose-fitting apparel (also known as comfort stretch apparel) or external stress such as grabbing and pulling. Additionally, comfort apparel can be subjected to prolonged stress, such as stretching to accommodate positions such as sitting. Another example of prolonged stress occurs when a fabric is required to stretch to accommodate fitting the form of the body, such as swimwear, anchored slacks, and other form-fitting apparel (also known as semi-support apparel).5.1.2 Fabric growth can also be in response to a variety of stresses. This method evaluates fabric growth due to exposure to prolonged stresses. In form-fitting apparel, fabric growth can apply as garments are worn for a prolonged period of time or under long periods of stress such as sitting. Upon removal of garments or stress, its growth can be seen and evaluated.5.2 This test method is not recommended for acceptance testing of commercial shipment because the between-laboratory precision is known to be poor.5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, ensure the test samples to be used are as homogeneous as possible, are drawn from the material from which the disparate test results are obtained, and are assigned randomly in equal numbers to each laboratory for testing. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.1.1 This test method covers the measurement of fabrics that exhibit high stretch and good recovery from low tension. Fabric stretch is measured when a known load is applied. Fabric growth is evaluated after a known extension is applied and subsequently removed.1.2 The procedures for fabric stretch and fabric growth can be used together, or individually.1.3 While this test method can be used for a knit fabric, fabrics intended for support or other applications are better evaluated using other test methods: D3107, D4964, D6614.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Upon mutual agreement between the purchaser and the supplier, woven and knitted products intended for this end use should meet all of the requirements listed in Table 1 of this specification.4.2 It is recognized that for purposes of fashion or aesthetics, the ultimate consumer of articles made from these fabrics may find acceptable products that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the supplier.4.2.1 In such cases, any references to the specification shall specify that: “This product meets ASTM Specification ____ except for the following characteristic(s).”4.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular product.4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods. For additional information see Test Methods D629, Practice D1776, and Guide D3938.1.1 This specification covers the evaluation of specific performance characteristics of importance in woven and knit flat, fitted, and waterbed sheet products for use in institutional and household environments.1.2 This specification may be used by mutual agreement between the purchaser and the supplier to establish purchasing specification requirements.1.3 The requirements in Table 1 apply to the length and width directions for those properties where fabric direction is pertinent.1.4 This specification is not applicable to woven and knit products used for sheet blankets or to woven and knitted sheet products used for apparel.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier.5.2.1 In such cases, any references to the specification shall specify that. “This fabric meets ASTM Specification D4115 except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The significance and use of particular properties and methods are discussed in the appropriate sections of the specified methods.1.1 This performance specification covers woven and knitted fabrics comprised of any textile fiber or mixture of fibers to be used in women's and girls' dress gloves.1.2 This performance specification is not applicable to fabrics used for interlinings and industrial-protective clothing.1.3 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent.1.4 The following precautionary statement pertains only to the test methods portion, Section 7, of this performance specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Upon agreement between the purchaser and the supplier, fabrics intended for this end use should meet all the requirements listed in Table 1 of this performance specification.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the supplier.5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4116 except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and the supplier, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.1.1 This performance specification covers woven and knitted fabrics composed of any textile fiber or mixture of fibers used in corsets, girdles or a combination of the same.1.2 This performance specification is not applicable to knitted or woven corset-girdle-combination fabrics, to knitted lace fabrics, and to fabrics used for interlinings.1.3 These requirements apply to the length and width directions for those properties where each fabric direction is pertinent.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Upon agreement between the purchaser and the seller, fabrics intended for this end use should meet all of the requirements listed in Table 1 of this performance specification.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified upon agreement between the purchaser and the seller.5.2.1 In such cases, any references to the specification shall specify that: “This fabric meets ASTM Specification D4119 except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The uses and significance of particular properties and methods are discussed in the appropriate sections of the specified methods.1.1 This performance specification covers knitted fabrics comprised of any textile fiber or mixture of fibers, used in men's and boy's dress shirts.1.2 This performance specification is not applicable to knitted fabrics used for interlinings.1.3 These requirements apply to both the length and width directions for those properties where fabric direction is pertinent.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This performance specification covers knitted fabrics for men's and boys' bathrobes, dressing gowns, and pajamas.1.2 These performance requirements apply to the length and width directions for those properties where fabric direction is pertinent.1.3 The following precautionary caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

5.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them using competent statistical assistance. As a minimum, ensure that the test samples to be used are as homogeneous as possible and drawn from the material from which the disparate test results were obtained. The test specimens are to be randomly assigned in equal numbers to each laboratory for testing. The test results from the participating laboratories should be compared using a statistical test for unpaired data to a probability level chosen before initiation of the testing. If a bias is found, either its cause shall be found and corrected, or future test results for that material shall be adjusted in consideration of the known bias.5.2 The results obtained by this test method may be used to determine if fabrics meet the tolerances for fabric counts given in Specification D3887.1.1 This test method covers the measurement of wale and course counts of weft knitted fabrics. Weft knit fabrics are made on circular or flat-bed knitting machines and include single- as well as double-knit fabric categories. Typical examples of single-knits include jersey and single-pique fabrics; typical double-knits are rib, interlock, and swiss pique fabrics.1.2 This test method is not applicable to warp knit fabrics such as tricot or raschel.1.3 Wale and course counts are to be reported separately.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Upon mutual agreement between the purchaser and the seller, woven fabrics intended for this end use should meet all of the requirements listed in Table 1 of this specification.(A) More than one method can be used to measure these properties. These methods cannot be used interchangeably since there can be no overall correlation between them (see Note 2, Note 3, and Note 7).(B) AATCC Gray Scale for Color Change.(C) AATCC Gray Scale for Staining.(D) AATCC 9-Step Chromatic Transference Scale.(E) It has been reported that the results for staining, obtained by standard AATCC Test Methods, on fabrics dyed to dark shades that contain a combination of polyester and spandex, or their blends, may not show the full staining propensity of such fabrics in consumer use. It is, therefore, recommended that the staining results obtained by these tests not be used for acceptance testing of such fabrics.4.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and the seller.4.2.1 In such cases, any references to the specification shall specify that: This fabric meets ASTM Specification D3655 except for the following characteristic(s).4.3 Where no prepurchase agreement has been reached between the purchaser and the seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As noted in 4.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.4.4 The uses and significance of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This performance specification covers men's and women's sliver knitted overcoat and jacket fabrics composed of any textile fiber or mixture of textile fibers.1.2 This performance specification is not applicable to knitted fabrics used for interlinings.1.3 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Upon mutual agreement between the purchaser and seller, fabrics intended for this end use should meet all the requirements listed in Table 1 of this specification.5.2 It is recognized that for purposes of fashion or aesthetics the ultimate consumer of articles made from these fabrics may find acceptable fabrics that do not conform to all of the requirements in Table 1. Therefore, one or more of the requirements listed in Table 1 may be modified by mutual agreement between the purchaser and seller.5.2.1 If any of the requirements in Table 1 are modified by mutual agreement between purchaser and seller, any reference to the specification shall state that: “This fabric meets ASTM Specification D4769, except for the following characteristic(s).”5.3 Where no prepurchase agreement has been reached between the purchaser and seller, and in case of controversy, the requirements listed in Table 1 are intended to be used as a guide only. As stated in 5.2, ultimate consumer demands dictate varying performance parameters for any particular style of fabric.5.4 The significance and use of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This specification covers woven and warp knitted comforter fabrics, composed of any textile fiber, or mixture of fibers.1.2 These requirements apply to the length and width directions for those properties where fabric direction is pertinent.1.3 The following safety hazards caveat pertains only to the test methods described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车