1.1 These tables define an air mass 1.5 solar spectral irradiance distribution for use in all solar applications where a standard terrestrial spectral irradiance is required for the direct normal radiation. A similar standard for global irradiance on a 37° tilted surface is given in Standard E892. 1.2 These tables are modeled data that were generated using a zero air mass solar spectrum based on the revised extraterrestrial spectrum of Neckel and Labs (1), the BRITE (3, 4) Monte Carlo radiative transfer code, and the 1962 U.S. Standard Atmosphere (5) with a rural aerosol (6, 7, 8). Further details are presented in Appendix XI. 1.3 The air mass zero (AM0) spectrum that was used to generate the terrestrial spectrum was provided by C. Frohlich and C. Wehrli (1) and is a revised and extended Neckel and Labs (2) spectrum. Neckel and Labs revised their spectrum by employing newer limb-darkening data to convert from radiance to irradiance, as reported by Frohlich (9), citing the study by Hardrop (10). Comparisons by Frohlich with calibrated sunphotometer data from Mauna Loa, Hawaii, indicate that this new extraterrestrial spectrum is the best currently available. 1.4 The development of the terrestrial solar spectrum data is based on work reported by Bird, Hulstrom, and Lewis (11). In computing the terrestrial values using the BRITE Monte Carlo radiation transfer code, the authors cited took the iterations to 2.4500 [mu]m only. We have extended the spectrum to 4.045 [mu]m using sixteen E[lambda]i values from the original Standard E891-82. Irradiance values in Standard E891-82 were computed from the extraterrestrial spectrum represented by Standard E490. The additional data points were added to account for the solar irradiance in this region that account for approximately 1.5% of the total irradiance between 0.305 and 4.045 [mu]m. The errors propagated by doing so are insignificant. 1.5 An air mass of 1.5 and a turbidity of 0.27 were chosen for this standard because they are representative of average conditions in the 48 contiguous states of the United States.

定价： 0元 / 折扣价： 0 元

1.1 These tables define an air mass 1.5 solar spectral irradiance distribution for use in all solar applications where a standard terrestrial spectral irradiance is required for that part of solar irradiance, diffuse, and direct, that is incident on a sun-facing, 37°-tilted surface. A similar standard for direct normal irradiance is given in Standard E891. 1.2 These tables are modeled data that were generated using a zero air mass solar spectrum based on the revised extraterrestrial spectrum of Neckel and Labs (1), the BRITE (3, 4) Monte Carlo radiative transfer code, and the 1962 U.S. Standard Atmosphere (5) with a rural aerosol (6, 7, 8). Further details are presented in Appendix X1. 1.3 The air mass zero (AM0) spectrum that was used to generate the terrestrial spectrum was provided by C. Frohlich and C. Wehrli (1) and is a revised and extended Neckel and Labs (2) spectrum. Neckel and Labs revised their spectrum by employing newer limb-darkening data to convert from radiance to irradiance, as reported by Frohlich (9), citing the study by Hardrop (10). Comparisons by Frohlich with calibrated sunphotometer data from Mauna Loa, Hawaii, indicate that this new extraterrestrial spectrum is the best currently available. 1.4 The development of the terrestrial solar spectrum data is based on work reported by Bird, Hulstrom, and Lewis (11). In computing the terrestrial values using the BRITE Monte Carlo radiation transfer code, the authors cited took the iterations to 2.4500 [mu]m only. We have extended the spectrum to 4.045 [mu]m using sixteen [lambda]i values from the original Standard E892-82. Irradiance values in Standard E892-82 were computed from the extraterrestrial spectrum represented by Standard E490. The additional data points were added to account for the solar irradiance in this region that account for approximately 1.5% of the total irradiance between 0.305 and 4.045 [mu]m. The errors propagated by doing so are insignificant. 1.5 An air mass of 1.5, a turbidity of 0.27, and a tilt of 37° were chosen for this standard because they are representative of average conditions in the 48 contiguous states of the United States.

定价： 0元 / 折扣价： 0 元

5.1 This standard does not purport to address the mean spectral irradiance incident on tilted or vertical fenestration or building-integrated systems over a day, a season, or a year. The spectral irradiance distributions have been chosen to represent a reasonable near-upper limit for solar radiation when these systems are exposed to clear-sky conditions similar to those used to calculate solar heat loads of buildings. The diffuse spectral irradiance distributions can also be used to represent conditions when these systems are shaded from the direct sun.5.2 Absorptance, reflectance, and transmittance of solar radiation are important factors in studies of light transmission through semi-transparent plates. These properties are normally functions of wavelength, which require that the spectral distribution of the solar flux be known before the solar-weighted property can be calculated.5.3 To compare the relative performance of competitive products by computerized simulations, or to compare the performance of products subjected to experimental tests in laboratory conditions, a reference standard solar spectral distribution for both direct and diffuse irradiance is desirable.5.4 The table provides appropriate standard spectral irradiance distributions for determining the relative optical performance of semi-transparent materials and other systems. The table may be used to evaluate components and materials for the purpose of solar simulation where the direct and the diffuse spectral solar irradiances are needed separately.5.5 The selected air mass value of 1.5 for a plane-parallel atmosphere above a flat earth corresponds to a zenith angle of 48.19°. The SMARTS2 computation of air mass accounts for atmospheric curvature and the vertical density profile of molecules, which results in a solar zenith angle of 48.236°, or an equivalent plane-parallel-atmosphere air mass of 1.50136. The angle of incidence computed by SMARTS for the direct beam irradiance incident on a 20°-tilted plane facing the sun is thus 28.236°. It is 41.764° for a 90°-tilted surface facing the sun.5.6 A plot of the SMARTS model output for the reference direct radiation on a 20° and 90° tilted surfaces is shown in Fig. 1. A similar plot, but for diffuse radiation, is shown in Fig. 2.5.7 The input needed by SMARTS to generate the spectra for the prescribed conditions and the 20°-tilted surface is provided in Table 1. The input file for the 90°-tilted surface differs only by one line. This modified line appears in Table 2.5.8 The total irradiance, integrated over the spectral range 280–4000 nm, is 791.07, 93.02, 97.96, and 889.03 W·m-2 for direct, sky diffuse, total diffuse and global radiation incident on the 20° tilted surface, respectively. It is 669.74, 58.66, 140.56, and 810.30 W·m-2 for direct, sky diffuse, total diffuse and global radiation incident on the 90° tilted surface, respectively.5.9 The availability of the adjunct standard computer software for SMARTS allows one to (a) reproduce the reference spectra, using the above input parameters; (b) compute test spectra to attempt to match measured data at a specified FWHM, and evaluate atmospheric conditions; (c) compute test spectra representing specific conditions for analysis vis-à-vis any one or all of the reference spectra; (d) obtain the sky diffuse and the ground-reflected diffuse spectra (whose sum appears in the table) separately; and (e) smooth the spectral results to different resolution and wavelength step by using the postprocessing options.1.1 This table provides terrestrial solar spectral irradiance distributions that may be employed as weighting functions to (1) calculate the broadband solar or light transmittance of fenestration from its spectral properties; or (2) evaluate the performance of building-integrated technologies such as photovoltaic electricity generators. Most of these systems are installed on vertical walls, but some are also installed on pitched roofs or on other tilted structures, such as sunspaces. Glazing transmittance calculations or measurements require information on both the direct and diffuse components of irradiance. The table provides separate information for direct and diffuse irradiance, and for two different tilt angles, 20° and 90° relative to the horizontal. All distributions are provided at 2002 wavelengths within the spectral range 280–4000 nm. The data contained in this table reflect reference spectra with uniform wavelength interval (0.5 nanometer (nm) below 400 nm, 1 nm between 400 and 1700 nm, an intermediate wavelength at 1702 nm, and 5 nm intervals from 1705 to 4000 nm). The data table represents reasonable cloudless atmospheric conditions favorable for the computerized simulation, comparative rating, or experimental testing of fenestration systems.1.2 The data contained in this table were generated using the SMARTS version 2.9.2 atmospheric transmission model developed by Gueymard (1, 2).1.3 The selection of the SMARTS radiative model to generate the spectral distributions is chosen for compatibility with previous standards (ASTM G173 and G177). The atmospheric and climatic conditions are identical to those in ASTM G173. The environmental conditions are also identical, with only one exception (see sections 4.3 and X1.2).1.4 The table defines four solar spectral irradiance distributions:1.4.1 Separate direct and diffuse solar spectral irradiance incident on a sun-facing, 20° tilted surface in the wavelength region from 280–4000 nm for air mass 1.5, at sea level.1.4.2 Separate direct and diffuse solar spectral irradiance incident on a sun-facing, 90° (vertical) tilted surface in the wavelength region from 280–4000 nm for air mass 1.5, at sea level.1.5 The diffuse spectral distribution on a vertical surface facing away from the sun (i.e., shaded), or at any prescribed azimuth away from the sun, may be computed using the model to obtain representative results (i.e., results that fall within an acceptable range of variance).1.6 The climatic, atmospheric, and geometric parameters selected reflect the conditions to provide a realistic set of spectral distributions appropriate for building applications under very clear-sky conditions, representative of near-maximum solar heat gains in buildings.1.7 A wide variety of orientations or local environmental conditions is possible for exposed surfaces. The availability of the SMARTS model (as an adjunct to this standard) used to generate the standard spectra allows users to evaluate spectral differences relative to the spectra specified here.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 843元 / 折扣价： 717 元 加购物车

This specification provides the performance requirements and parameters used for classifying both pulsed and steady state solar simulators intended for indoor testing of photovoltaic devices (solar cells or modules), according to their spectral match to a reference spectral irradiance, non-uniformity of spatial irradiance, and temporal instability of irradiance. The classification of a solar simulator is based on the size of the test plane, and does not provide any information about electrical measurement errors that are related to photovoltaic performance measurements obtained with a classified solar simulator.1.1 This classification provides means for assessing the suitability of solar simulators for indoor electrical performance testing of photovoltaic cells and modules, that is, for measurement current-voltage curves under artificial illumination.1.2 Solar simulators are classified according to their ability to reproduce a reference spectral irradiance distribution (see Tables G138 and E490), the uniformity of total irradiance across the test plane, and the stability of total irradiance over time.1.3 A solar simulator usually consists of three major components: (1) light source(s) and associated power supplies; (2) optics and filters required to modify the irradiance at the test plane; and (3) controls to operate the simulator, including irradiance adjustment.1.4 This classification is applicable to both pulsed and steady-state solar simulators.1.5 Many solar simulators also include integral data acquisition systems for photovoltaic performance testing; these data acquisition systems are outside of the scope of this classification.1.6 Light sources for weathering, durability, or conditioning of photovoltaic devices are outside of the scope of this classification.1.7 This classification is not applicable to solar simulators intended for testing photovoltaic concentrator devices.1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.9 The following precautionary caveat pertains only to the hazards portion, Section 6, of this classification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

6.1 The primary goal of this practice is to extract representative samples from PV modules for TCLP toxicity testing purposes in order to receive unbiased, comparable and repeatable toxicity test results from independent TCLP testing laboratories.6.2 Solar photovoltaic (PV) modules in the United States and the world reaching end-of-life due to failure, underperformance or breakage due to extreme weather have to be recycled or otherwise safely disposed of following the Resource Conservation and Recovery Act (RCRA) regulation [United States, Resource Conservation and Recovery Act. Pub.L. 94–580, October 1976]. For end-of-life PV modules, the U.S. Environmental Protection Agency (EPA) Method 1311 (TCLP) is used for waste characterization based on leaching potential under simulated landfill conditions.6.3 Commercial PV modules contain compounds and alloys of various metals (for example, Ag, Al, Cd, Cu, Ga, In, Ni, Pb, Se, Sn, Te, Zn) which are used in semiconductor compounds and electrical contacts.5 Modules that pass the EPA Method 1311 TCLP test, and state protocols (if applicable), can be disposed of in a regular landfill. Otherwise, they are classified as hazardous waste and must go through a more onerous and expensive disposal process. Currently, there is no national or international standard, nor a standardized protocol available for removal of test samples from PV modules for toxicity testing per the EPA Method 1311 standard.6.4 The validity of the toxicity test results heavily depends on the location of extracted samples in the module, specifically within the laminate area, and the particle size of the extracted samples. Therefore, it is critical that the sample extraction procedure be properly designed to avoid biased or otherwise inaccurate toxicity test results.6.5 The development and application of a homogeneous and representative sampling standard will help utilities and manufacturers to limit the number of variables and to obtain repeatable test results.1.1 The purpose of this practice is to describe a representative and repeatable sample preparation methodology to conduct toxicity testing on solar photovoltaic (PV) modules for use with EPA Test Method 1311: Toxicity Characteristic Leaching Procedure (TCLP).1.2 This practice refers to the extraction and preparation of PV module samples by EPA Method 1311, the testing for eight (8) distinct metals – mercury (by Method 7470A), arsenic, barium, cadmium, chromium, lead, selenium and silver (by Method 6010C) as well as the analysis and interpretation of the test results on a module level.1.3 This practice applies to only (1) standard crystalline silicon (c-Si) modules, multi and mono-crystalline silicon with aluminum back surface field (Al-BSF) cell technology and (2) cadmium telluride (CdTe) PV modules.1.4 Other and newer PV technologies and module architectures, for example, passivated emitter and rear cell (PERC), interdigitated back contact (IBC), hetero-junction technology (HJT), multiwire, half cut, shingled etc., have not been evaluated with this practice, although the concept and practice can be easily extended and applied to other technologies following the conceptual approach presented in this document.1.5 The sample extraction/removal methodology applied in this practice is the waterjet cutting sampling method. Sample extraction with mechanical cutting has been extensively evaluated but the variability of TCLP test results based on the mechanical cut samples tend to be much higher (30 %) than that of the waterjet cut samples (8 %).2 Therefore, the mechanical cut method is not presented in this practice.1.6 Only the laminate area of the PV module is considered for TCLP testing, as other possible module parts, such as aluminum frame, junction box and cables contain recyclable materials that are already well-documented and are not specific to the PV modules.1.7 The material gravimetric density (g/cm3) throughout the laminate area is considered constant.1.8 This practice was developed to be consistent with three fundamental requirements:1.8.1 Sample pieces with particle size not to exceed the allowed size limit of EPA 1311 standard which is 9.5 mm,1.8.2 The particle size used in this practice as sample piece is consistent with the median particle size expected in landfill disposal2, and1.8.3 An assumption that each laminate sample piece will result in 100 % glass coverage area, due to the presence of bonding encapsulant layers once it is broken in the landfill.1.9 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.10 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.11 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

5.1 The temperatures of opaque surfaces exposed to solar radiation are generally higher than the adjacent air temperatures. In the case of roofs or walls enclosing conditioned spaces, increased inward heat flows result. In the case of equipment or storage containers exposed to the sun, increased operating temperatures usually result. The extent to which solar radiation affects surface temperatures depends on the solar reflectance of the exposed surface. A solar reflectance of 1.0 (100 % reflected) would mean no effect on surface temperature while a solar reflectance of 0 (none reflected, all absorbed) would result in the maximum effect. Coatings of specific solar reflectance are used to change the temperature of surfaces exposed to sunlight. Coatings and surface finishes are commonly specified in terms of solar reflectance. The initial (clean) solar reflectance must be maintained during the life of the coating or finish to have the expected thermal performance.5.2 The test method provides a means for periodic testing of surfaces in the field or in the laboratory. Monitor changes in solar reflectance due to aging and exposure, or both, with this test method.5.3 This test method is used to measure the solar reflectance of a flat opaque surface. The precision of the average of several measurements is usually governed by the variability of reflectances on the surface being tested.5.4 Use the solar reflectance that is determined by this method to calculate the solar energy absorbed by an opaque surface as shown in Eq 1.5.4.1 Combine the absorbed solar energy with conductive, convective and other radiative terms to construct a heat balance around an element or calculate a Solar Reflectance Index such as that discussed in Practice E1980.1.1 This test method covers a technique for determining the solar reflectance of flat opaque materials in a laboratory or in the field using a commercial portable solar reflectometer. The purpose of the test method is to provide solar reflectance data required to evaluate temperatures and heat flows across surfaces exposed to solar radiation.1.2 This test method does not supplant Test Method E903 which measures solar reflectance over the wavelength range 250 nm to 2500 nm using integrating spheres. The portable solar reflectometer is calibrated using specimens of known solar reflectance to determine solar reflectance from measurements at four wavelengths in the solar spectrum: 380 nm, 500 nm, 650 nm, and 1220 nm. This technique is supported by comparison of reflectometer measurements with measurements obtained using Test Method E903. This test method is applicable to specimens of materials having both specular and diffuse optical properties. It is particularly suited to the measurement of the solar reflectance of opaque materials.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This terminology pertains to photovoltaic (radiant-to-electrical energy conversion) device performance measurements and is not a comprehensive list of terminology for photovoltaics in general.1.2 Additional terms used in this terminology and of interest to solar energy may be found in Terminology E 772.

定价： 0元 / 折扣价： 0 元

5.1 The solar reflectance of a DRM depends on the solar incidence angle. This method is intended to provide solar reflectance values for DRM roofing products.1.1 This test method covers a technique for determining the solar reflectance of a directionally reflective material using a commercial portable solar reflectometer, including but not limited to roofing materials with granules or surface design that results in angularly dependent reflectance. The purpose of the method is to evaluate the seasonal and annual solar reflectances of a directionally reflective roofing product.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This practice is intended to serve as a guide to manufacturers, distributors, installers, contractors, regulatory officials, and owners. It is not intended to specify detailed methods of testing, installation, or servicing for the system or any of its components.4.2 This practice sets forth those methods and components necessary for minimum operation and safety. It also suggests methods for improved operation and effectiveness.1.1 This practice provides descriptions of solar domestic water heating systems and sets forth installation and service practices in new and existing one- and two-family dwellings to help ensure adequate operation and safety.2,31.2 This practice applies regardless of the fraction of heating requirement supplied by solar energy, the type of conventional fuel used in conjunction with solar, or the heat transfer fluid (or fluids) used as the energy transport medium. However, where more stringent requirements are recommended by the manufacturer, these manufacturer requirements shall prevail.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Sections 6 and 7.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

5.1 Glazed apertures in buildings are commonly utilized for the controlled admission of both light and solar radiant heat energy into the structure. Other devices may also be used to reflect light and solar radiant heat into a building.5.1.1 Most of the solar radiant energy entering a building in this manner possesses wavelengths that lie between 300 and 2500 nm (3000 to 25 000 Å). Only the portion between 380 and 760 nm is visible radiation, however. In daylighting applications, it is therefore important to distinguish the solar radiant energy transmittance and reflectance of these materials from their luminous (visual or photometric) transmittance and reflectance.5.2 For comparisons of the energy and illumination performances of building fenestration systems it is important that the calculation or measurement, or both, of solar radiant and luminous transmittance and reflectance of materials used in fenestration systems use the same incident solar spectral irradiance distribution.5.2.1 Solar luminous transmittance and reflectance are important properties in describing the performance of components of solar illumination systems (for example, windows, clerestories, skylights, shading and reflecting devices) and other fenestrations that permit the passage of daylight as well as solar energy into buildings.5.3 This practice is useful for determining the luminous transmittance and reflectance of glazing materials and diffusely or quasi-diffusely reflecting materials used in daylighting systems. For the results of this practice to be meaningful, inhomogeneities or corrugations in the sample must not be large. Test Method E1175 (or Test Method E972) is available for sheet materials that do not satisfy this criterion.1.1 This practice describes the calculation of luminous (photometric) transmittance and reflectance of materials from spectral radiant transmittance and reflectance data obtained from Test Method E903.1.2 Determination of luminous transmittance by this practice is preferred over measurement of photometric transmittance by methods using the sun as a source and a photometer as detector except for transmitting sheet materials that are inhomogeneous, patterned, or corrugated.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 Glazed apertures in buildings are generally utilized for the controlled admission of both light and solar radiant heat energy into the structure. Other devices may also be used to reflect light and solar radiant heat into a building.5.2 The bulk of the solar radiant energy entering a building in this manner possesses wavelengths that lie from 300 to 2500 nm (3000 to 25 000 Å). Only the portion from 380 to 760 nm (3800 to 7600 Å) is visible radiation, however. In daylighting applications, it is therefore important to distinguish the radiant (solar radiant energy) transmittance or reflectance of these materials from their luminous (light) transmittance or reflectance.5.3 For comparisons of the energy and illumination performances of building fenestration systems it is important that the calculation or measurement, or both, of solar radiant and luminous transmittance and reflectance of materials used in fenestration systems use the same incident solar spectral distribution.5.4 Solar luminous transmittance and reflectance are important properties in describing the performance of components of solar illumination systems including windows, clerestories, skylights, shading and reflecting devices, and other passive fenestrations that permit the passage of daylight as well as solar radiant heat energy into buildings.5.5 This test method is useful for determining the solar luminous transmittance and reflectance of optically inhomogeneous sheet materials and diffusely reflecting materials used in natural lighting systems that are used alone or in conjunction with passive or active solar heating systems, or both. This test method provides a means of measuring solar luminous transmittance under fixed conditions of incidence and viewing. This test method has been found practical for both transparent and translucent materials as well as for those with transmittances reduced by reflective coatings. This test method is particularly applicable to the measurement of luminous transmittance of inhomogeneous, fiber reinforced, patterned, corrugated, or otherwise optically inhomogeneous materials when the transmittance is averaged over an area that is large in comparison to the inhomogeneities.1.1 This test method covers the measurement of solar photometric transmittance of materials in sheet form. Solar photometric transmittance is measured using a photometer (illuminance meter) in an enclosure with the sun and sky as the source of radiation. The enclosure and method of test is specified in Test Method E1175 (or Test Method E1084).1.2 The purpose of this test method is to specify a photometric sensor to be used with the procedure for measuring the solar photometric transmittance of sheet materials containing inhomogeneities in their optical properties.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Solar reflectance is an important factor affecting the temperature of a sunlit surface and that of the near-surface ambient air temperature. The test method described herein measures the solar reflectance of surfaces in natural sunlight.1.1 This test method covers the measurement of solar reflectance of various horizontal and low-sloped surfaces and materials in the field, using an albedometer or pyranometer. The test method is intended for use when the sun angle to the normal from a surface is less than 45°.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the general and physical requirements for commercial standard solar screening woven from vinyl-coated fiber glass yarn. The material shall conform to general and physical requirements of this specification. General requirements include workmanship, plasticizers, color, selvage, yarn splices, and container dimensions and rolls put-up. Physical requirements include roll appearance, mesh, roll length, roll width, mass per unit area, ignition loss, breaking strength, fabric stability, shading coefficient, flame resistance, blocking resistance, and color stability to accelerated weathering. Testing of both general and physical requirements shall conform to the test methods detailed in this specification. Lot and sample size shall be according to the acceptance number of the specification.1.1 This specification covers the requirements for vinyl-coated fiber glass solar screening, and should help users recognize the characteristics of acceptable vinyl-coated fiber glass solar screening. This specification is limited in application to vinyl-coated fiber glass solar screening that is produced with a ribbed pattern woven in the warp direction. The applicability of this specification to vinyl-coated fiber glass type solar screening of a non-rib, a double rib (ribs in both warp and filling direction), or a filling rib construction is not known.1.2 This specification shows the definitions, general requirements, and physical requirements for commercial standard vinyl-coated fiber glass solar screening designed and woven for installation in any dwelling, building, or structure for the purpose of providing a significant reduction in solar heat gain, while providing outward view and interior light. Solar screening provides a structure that has insect-restraining capabilities equivalent to standard insect screening.NOTE 1: For information on standard insect screening, see Specification D3656/D3656M.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 The following precautionary caveat pertains only to the test method portion, Sections 8 – 21 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the general requirements for materials used in rubber seals of concentrating solar collectors. Design requirement pertains only to permissible deflections of the rubber during thermal expansion or contraction of the seal in use and the tolerances in dimensions of molded and extruded seals. The materials shall be classified according to usage: Type C and Type W; according to degrees of hardness: Grade 2; 3; 4; 5; 6; 7; and 8. The seals shall be classified as: Class PS and Class SC. Desert outdoor exposure and xenon arc laboratory exposure shall be performed to determine the resistance to solar radiation. The following test methods shall be performed: ultimate elongation; compression set; resistance to heating; resistance to ozone; resistance to low temperature; and adhesion loss.1.1 This specification covers the general requirements for materials used in rubber seals of concentrating solar collectors. Particular applications may necessitate other requirements that would take precedence over these requirements when specified.1.2 Design requirement pertains only to permissible deflections of the rubber during thermal expansion or contraction of the seal in use and the tolerances in dimensions of molded and extruded seals.1.3 This specification does not include requirements pertaining to the fabrication or installation of the seals.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This practice sets forth the acceptable installation and service use of solar space heating systems for one- and two-family dwellings to help ensure adequate performance, safety, and consumer satisfaction. This practice, however, does not apply to Rankine cycle, heat pump, or high pressure vapor systems, and is not intended to abridge safety or health requirements. Specifications are provided for the following system components: collector subsystems; thermal storage devices; controls and safety devices; piping, ducting, and ancillary equipment; electrical wiring; and auxiliary (nonsolar) space-heating equipment.1.1 This practice covers solar space heating systems for one- and two-family dwellings. It sets forth acceptable installation and service practices to help ensure adequate performance, safety, and consumer satisfaction.1.2 This practice is intended to describe acceptable practices for space heating systems in new and existing dwellings and shall not be construed as the optimization of good practices.1.3 This practice does not apply to Rankine cycle, heat pump, or high pressure vapor systems.1.4 This practice is not intended to abridge safety or health requirements. All systems shall be installed in accordance with local codes and ordinances.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (For specific safety precautions, see Section 6).1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车