5.1 This test method relates efficiency of operation of domestic heating equipment to clean burning. Reducing combustion air in a burner gives more efficient operation. The extent to which combustion air can be reduced is limited by the onset of unacceptable smoke production. By delineating the relation between smoke density and air supply, this test method (together with net stack temperature data) defines the maximum efficiency for a given installation at any acceptable smoke level.5.2 For certain types of equipment, such as the rotary wall-flame burner, too much excess air will cause smoke as well as too little. For these cases, the point of minimum excess air at the acceptable smoke level indicates the optimum efficiency.5.3 The operating temperatures of the equipment will affect these test results. The relation of excess air to smoke density is thus susceptible to some change at different points in an operating cycle. In practice, an adequate compromise is possible by operating the burner for 15 min before any readings are recorded and then obtaining the test data within a succeeding 25 min period.5.4 Under laboratory conditions, CO2 readings are reproducible to ±0.3 % and smoke readings are reproducible to ±1/2 smoke spot number.1.1 This test method covers the evaluation of the performance of distillate fuels from the standpoint of clean, efficient burning. It is intended primarily for use with home heating equipment burning No. 1 or No. 2 fuel oils. It can be used either in the laboratory or in the field to compare fuels using a given heating unit or to compare the performance of heating units using a given fuel.NOTE 1: This test method applies only to pressure atomizing and rotary-type burners.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.2.1 Arbitrary and relative units are also used.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 A supply well provides groundwater for household, domestic, commercial, agricultural, or industrial uses.4.2 Using a standardized protocol based on an existing industry standard or approved regulatory methods and procedures to collect water samples from a supply well is essential to obtain representative water quality data. These data can be critical to efforts to protect water uses, and human health, and identify changes when they occur. Use of this guide will help the project team to design and execute an effective water supply sampling program.4.3 It is important to understand the objectives of the sampling program before designing it. Water supplies may be sampled for various reasons including any or all of the following:(1) baseline sampling before an operation of concern,(2) periodic sampling during such an operation,(3) investigative responses to perceived changes in water quality, or(4) ongoing monitoring related to known or potential groundwater constituents of concern in the area.Sampling programs should be based on these objectives and be developed in coordination with the prospective laboratory(ies) to ensure its procedures, capabilities, and limitations meet the needs of the program, protect human health and fulfill regulatory requirements.1.1 This guide presents a methodology for obtaining representative groundwater samples from domestic or commercial water wells that are in proximity to oil and gas exploration and production (E&P) operations. E&P operations include, but are not necessarily limited to, site preparation, drilling, completion, and well stimulation (including hydraulic fracturing), and production activities. The goal is to obtain representative groundwater samples from domestic or commercial water wells that can be used to identify the baseline groundwater quality and any subsequent changes that may be identified. While this guide focuses on baseline sampling in conjunction with oil and gas E&P activities, the principles and practices recommended are based on well-established methods that have been in use for many years in other industrial situations. This guide recommends sampling and analytical testing procedures that can identify various chemical species present including metals, dissolved gases (such as methane), hydrocarbons (and other organic compounds), as well as overall water quality.1.2 This guide provides information on typical residential and commercial water supply well systems and guidance on developing and implementing a sampling program, including determining sampling locations, suggested purging techniques, selection of potential analyses and laboratory certifications, data management, and integrity. It also includes guidance on personal safety. The information included pertains to baseline sampling before beginning any activities that could present potential risks to local aquifers, periodic sampling during and after such work, and ongoing monitoring relating to known or potential groundwater constituents in the area. This guide does not address policy issues related to frequency or timing of sampling or sampling distances from the wellhead. In addition, it does not address reporting limits, sample preservation, holding times, laboratory quality control, regulatory action levels, or interpretation of analytical results.1.3 These guidelines are not intended to replace or supersede regulatory requirements and technical methodology or guidance nor are these guidelines intended for inclusion by reference in regulations. Instances where this guide is in conflict with statutory or regulatory requirements, practitioners shall defer to the latter. These guidelines are intended to assist in developing sampling programs to meet project goals and objectives. However, site-specific conditions, regulatory requirements, site-specific health and safety issues, technical manuals and directives, and program data quality objectives should be evaluated and consulted along with the information contained in this guide for each individual site and sampling program.1.4 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project’s many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.1.5 Users are responsible for investigating and identifying all the legal and regulatory requirements that are applicable for the location where the sampling is being performed.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This guide recommends practices and solutions for global supply chain information exchange for substances, preparations, and articles as identified by REACH. The first five annexes of REACH guidance standards serve as a central repository for REACH industry guidance that spans industry sectors and facilitates collaboration across complex global supply chains. Annexes 6-9 provide key EU guidance on information exchange in the supply chain.5.2 Section 6 outlines the information that is to be exchanged in the supply chain both in the upstream and downstream directions.1.1 This guide will assist companies that manufacture, buy, or sell, or both, substances, preparations, and articles to ensure that supply chains comply with the European Union’s Registration, Evaluation, and Authorization of Chemicals (REACH) regulation. This is accomplished by identifying the specific information elements that must be specified, requested and exchanged in communication between actors in the supply chain.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 918元 / 折扣价： 781 元 加购物车