This practice details the standard procedure for evaluating the resistance of prestressed prepainted metal panels to cracking, or loss of adhesion, or both, after accelerated heat aging by dry heat test. This test method requires the use of gravity or forced air laboratory oven, bench vise, bending dies or test shims, 10x magnifier, and adhesive tape.1.1 This practice can be used to evaluate the resistance of a prestressed prepainted metal panel to cracking, or loss of adhesion, or both, after accelerated heat aging. Most coil coated products are formed and bent into specific shapes to produce a final product. These operations introduce stresses, which may be relieved by cracking of the coating after aging.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers two types and two grades of 2- and 3-wire, uncoated weldless steel and strand for use in pretensioned and posttensioned prestressed concrete construction. One specimen for test shall be taken from each production lot of finished strand and tested for breaking strength, yield strength and elongation. Strands of Grades 250 and 270 shall conform to specified breaking strength and yield strength requirements. Low relaxation strand shall also be tested as prescribed.1.1 This specification covers two types and two grades of 2-wire and 3-wire, uncoated steel strand for use in prestressed concrete construction. The two types of strand are low-relaxation and stress-relieved (normal-relaxation). Low-relaxation is to be regarded as the standard type. Stress-relieved (normal-relaxation) strand will not be furnished unless specifically ordered. The two grades are 250 [1725] and 270 [1860]. Grades 250 [1725] and 270 [1860] have minimum tensile strengths of 250 ksi [1725 MPa] and 270 ksi [1860 MPa] respectively, based on the nominal area of the strand.1.2 This specification is applicable for orders in either inch-pound units (as Specification A910) or in SI units (as Specification A910M).1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers uncoated, stress-relieved steel bars for prestressed concrete railroad ties. Analysis of the steel shall conform to the chemical requirements specified by the specification. Mechanical requirements including test method, tensile strength, yield strength, elongation and wrapping test are provided. One test specimen each for the tensile test and the wrapping test shall be taken for every 10 coils or fraction thereof in a lot.1.1 This specification covers low-relaxation steel bars for use in prestressed concrete railroad ties.1.2 This specification is applicable for orders in either inch-pounds units (as Specification A911) or in SI units (as Specification A911M).1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers seven-wire, uncoated, compacted, stress-relieved steel strand for prestressed concrete. The chemical requirements, mechanical requirements, and dimensions and permissible variations are presented. The mechanical requirement includes breaking strength, load at 1% extension and elongation. Different test method shall be performed on the strand that includes dimension test, breaking strength test, load at 1% extension test, elongation test and workmanship.1.1 This specification covers two types and three grades of compacted, seven-wire, uncoated strand for use in prestressed concrete construction. The two types of strand are low-relaxation and stress-relieved (normal-relaxation). The three grades are 245 [1700], 260 [1800] and 270 [1860].1.2 This specification is applicable for orders in either inch-pound units (as Specification A779) or in SI units (as Specification A779M).1.3 The values stated in either inch-pound or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the specification.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers spun cast prestressed concrete bases used in tapered steel lighting poles. It provides requirements for acceptability of spun prestressed concrete bases produced in accordance with this specification, materials, bending test procedures, tolerances, and drawings. The requirements also cover inspection with respect to the quality of materials, the process of manufacture, and the finished bases.1.1 This specification covers spun cast prestressed concrete bases used in lighting structures.1.2 Units—The values stated in SI units are to be regarded as standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车