4.1 The use of the body measurement information in Tables 1 and 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures.)4.2 Three-dimensional avatars depicting each of the mature mens sizes in short, regular and tall, were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in the accompanying Tables. (Avatar 1-6) See Figs. 1-3.FIG. 1 Mature Men - ShortFIG. 2 Mature Men - RegularFIG. 3 Mature Men - Tall1.1 These tables list body measurements of mature male figure type, age 35 and older, sizes 34 through 52 in Short, Regular, and Tall. Although these are body measurements, they can be used as a baseline in designing apparel for Mature Men in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers the design and minimum performance criteria, and associated test methods (including apparatuses required for) for body protectors used in horse sports and horseback riding. The body protectors shall meet specified requirements for the material used, protector assembly, extent and form of protective material, attachments, and dimension, sizing, and body coverage. The testing procedures that the body protectors shall go through are shock attenuation test, penetration and deformation test, impact sites test, padding separation test, and closure test. Prior to testing, each body protector should be conditioned in accordance to ambient temperature, low temperature, high temperature, and water immersion.1.1 This specification covers minimum performance criteria and describes test methods for body protectors for use in horse sports and horseback riding.1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Tables 1 and 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635 Size Designation Procedures.)4.2 Three-dimensional avatars depicting each of the Misses Petite sizes and sub categories Curvy and Straight on certain measures were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in the accompanying Tables5 (Avatar 1-6) (see Figs. 1 and 2).FIG. 1 Missy Petite Avatar CurvyFIG. 2 Missy Petite Avatar Straight1.1 These tables list body measurements of adult female misses petite figure type sizes 00P through 20P. Although these are body measurements, they can be used as a baseline in designing apparel for Misses Petite in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of misses petite sizing.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This standard is a compilation of terminology related to the body dimensions for apparel sizing. 1.2 For definitions of other textile terms, refer to Terminology D123. 1.3 The terms are listed in alphabetical order regardless of whether they are horizontal or vertical measurements. The three dimensional Avatars were created by Alvanon Inc. See Figs. 1-19. 1.4 The term “height” has been designated for vertical measurements. 1.5 The term “length” has been designated for contour measurements.

定价： 646元 / 折扣价： 550 元 加购物车

5.1 Intervertebral body fusion device assemblies are generally simple geometric-shaped devices which are often porous or hollow in nature. Their function is to support the anterior column of the spine to facilitate arthrodesis of the motion segment. This test method outlines materials and methods for the characterization and evaluation of the mechanical performance of different intervertebral body fusion device assemblies so that comparisons can be made between different designs.5.2 This test method is designed to quantify the static and dynamic characteristics of different designs of intervertebral body fusion device assemblies. These tests are conducted in vitro to allow for analysis and comparison of the mechanical performance of intervertebral body fusion device assemblies to specific force modalities.5.3 The forces applied to the intervertebral body fusion assemblies may differ from the complex loading seen in vivo, and therefore, the results from these tests may not directly predict in vivo performance. The results, however, can be used to compare mechanical performance of different intervertebral body fusion device assemblies.5.4 Since the environment may affect the dynamic performance of intervertebral body fusion device assemblies, dynamic testing in a saline environment may be considered. Fatigue tests should first be conducted in air (at ambient temperature) for comparison purposes since the environmental effects could be significant. If a simulated in vivo environment is desired, the investigator should consider testing in a saline environmental bath at 37 °C (for example, 0.9 g NaCl per 100 mL water) at a rate of 1 Hz or less. A simulated body fluid, a saline drip or mist, distilled water, or other type of lubrication at 37 °C could also be used with adequate justification.5.5 If the devices are known to be temperature and environment dependent, testing should be conducted in physiologic solution as described in 5.4. Devices that require physiologic solution for testing should be tested in the same type solution for comparison purposes.5.6 The location within the simulated vertebral bodies and position of the intervertebral body fusion device assembly with respect to the loading axis will be dependent upon the design, the manufacturer’s recommendation, or the surgeon’s preferred method for implant placement.5.7 It is well known that the failure of materials is dependent upon stress, test frequency, surface treatments, and environmental factors. Therefore, when determining the effect of changing one of these parameters (for example, frequency, material, or environment), all others must be kept constant to facilitate interpretation of the results.1.1 This test method covers the materials and methods for the static and dynamic testing of intervertebral body fusion device assemblies, spinal implants designed to promote arthrodesis at a given spinal motion segment.1.2 This test method is intended to provide a basis for the mechanical comparison among past, present, and future nonbiologic intervertebral body fusion device assemblies. This test method allows comparison of intervertebral body fusion device assemblies with different intended spinal locations and methods of application to the intradiscal spaces. This test method is intended to enable the user to compare intervertebral body fusion device assemblies mechanically and does not purport to provide performance standards for intervertebral body fusion device assemblies.1.3 The test method describes static and dynamic tests by specifying force types and specific methods of applying these forces. These tests are designed to allow for the comparative evaluation of intervertebral body fusion device assemblies.1.4 These tests are designed to characterize the structural integrity of the device and are not intended to test the bone-implant interface.1.5 This test method does not address expulsion testing of intervertebral body fusion device assemblies (see 1.4).1.6 Guidelines are established for measuring displacements, determining the yield force or moment, and evaluating the stiffness and strength of the intervertebral body fusion device assemblies.1.7 Some intervertebral body fusion device assemblies may not be testable in all test configurations.1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard, with the exception of angular measurements, which may be reported in terms of either degrees or radians.1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 Properly sized and fitted body armor enhances the safety and performance of the wearer by providing protection while not restricting movement. Having body armor that fits well begins with appropriate and accurate measurements. The measurement guidance of this practice will facilitate consistency of measurement across the body armor industry and will help wearers understand proper measurements.4.2 Accurate measurements do not necessarily result in well-fitting armor, so this practice goes a step further by providing a description of well-fitting armor along with a personal armor fit assessment that the wearer can do for himself/herself.4.3 The measurement and fitting guidance specifically addresses officer-stated requirements for side overlap of front and back body armor panels, minimizing the armhole opening, eliminating any “V” gap (or similar) between the front and back panels, and providing vertical coverage on the front torso from approximately the “2nd uniform shirt button to 2 to 3 finger widths above duty belt.” Those requirements were considered in the development of this practice and the definition of measurements that can be consistently made for any individual.4.4 This practice describes measurements for the front, back, and sides of the wearer, in addition to girth measurements, to achieve proper sizing of front and back panels and proper fit of the complete armor.4.5 This practice can be used to train individuals on proper measurement techniques and to train wearers on proper fitting of body armor.1.1 This practice provides measurement and fit guidance for soft ballistic-resistant or stab-resistant body armor, or both, covering the torso. Proper measurement of the wearer and fitting of armor to that individual are necessary to obtain sufficient coverage of the torso and vital organs while allowing the full range of motion required for officer operations.1.2 This practice is primarily directed toward law enforcement and corrections officers and addresses measurements for and fit of concealable (normal duty) body armor worn under or over the uniform for both male and female wearers. This practice addresses only body armor composed of front and back protective panels contained within a carrier that positions and holds the panels on the torso.1.3 This practice can be used to train individuals on proper measurement techniques and to train wearers on proper fitting of body armor.1.4 Measurement guidance is provided in Section 5 of this practice.1.5 Guidance for use of a tape measure is provided in Section 6 of this practice.1.6 Guidance for use of sizing vests is provided in Section 7 of this practice.1.7 A personal armor fit assessment is provided in Section 8 for use by wearers.1.8 Units—English units are specified in this practice to be consistent with measurement units used in the United States body armor community. Approximate values in SI units are given in parentheses.1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

4.1 This guide is to be used to assist in the selection of containment boom in accordance with water body classifications.4.2 A small number of key parameters that generally affect boom performance have been used in Table 1, in order to enable the user to readily identify general criteria for boom selection.4.3 Many factors, other than those listed in Table 1, may be important in selecting containment boom for a particular application. Such factors include: flotation element length, wave length, the effect of stronger than minimum required strength members, shock loads, abrasion resistance, stability in roll, resistance to bridging, interval between anchor points and hand holds, use of reflectors or lighting, compatibility with fresh or salt water, and resistance to sunlight exposure.4.4 The values given in Table 1 are the recommended minimums for general purpose booms. As identified in 2.3, operational considerations may require trade-offs in boom properties. Special purpose booms, and general purpose booms used in special circumstances, may perform effectively with boom property values above or below those recommended in Table 1.4.5 Effective operation of oil spill control equipment depends on many factors, of which the prevailing environmental conditions are just a few. Factors such as, but not limited to, deployment techniques, level of training, personnel performance, and mechanical reliability can also affect equipment performance.1.1 This guide covers the selection of containment boom that may be used to control spills of oil and other substances that float on a body of water.1.2 This guide does not address the compatibility of spill control equipment with spill products. It is the user's responsibility to ensure than any equipment selected is compatible with anticipated products.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification describes a standardized method for preparation and verification of backing assemblies used in ballistic-resistant torso body armor testing and for reducing variability within and between laboratories. Included in this specification are the equipment used for preparation and verification of clay blocks, namely: backing fixture, backing fixture liner, bridge gauge, conditioning chamber, impactor, striking device, template, test setup, and velocity measurement equipment.This specification also covers procedures for characterization of clay block verification test setup, clay block preparation, clay block verification procedure prior to ballistic testing, clay block repair, clay block verification between test items, and clay block verification after final shot on clay block.1.1 The purpose of this specification is to provide standardized methods for preparation and verification of backing assemblies used in ballistic-resistant torso body armor testing and to reduce variability within and between laboratories.1.2 The backing assembly is a clay block that contains ROMA Plastilina No. 1®2 clay as the backing material. The clay serves as a witness material and provides a measurable indication of test item performance.1.3 This specification identifies two clay-verification impactors that may be used: (1) cylindrical and (2) spherical. Purchasers and other users will specify the clay-verification impactor to be used.1.4 This specification is primarily directed toward test laboratories but may be applicable to body armor manufacturers, researchers, and end users performing ballistic-resistance testing of body armor.1.5 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to non-SI units that are provided for information only.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 The scope of this terminology is to provide a standard terminology for body armor providing protection against ballistic threats, stabbing, fragmentation, blunt impact, or a combination of threats.1.2 The intent of this terminology is to have terms, abbreviations, and formulas that are applicable across federal agencies, law enforcement and corrections agencies, testing and certification bodies, and manufacturers.1.2.1 The terminology is kept general herein and should be defined more specifically as needed within individual test methods or other standards.1.3 This terminology is not intended to describe test methods or performance requirements for body armor.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This practice covers installation, inspection, and maintenance of valve body cavity pressure relief methods for valves used in geothermal and other high-temperature liquid service. The valve type covered by this practice is a design with an isolated body cavity such that when the valve is in either the open or closed position pressure is trapped in the isolated cavity, and there is no provision to relieve the excess pressure internally. The installation shall be such that direct access to the body cavity is maintained and that the pressure relief device may be periodically removed, cleaned, inspected, and reinstalled without endangering the operating personnel or removing the valve from its functional application. The relief device may be mounted with an automatic shutoff, such as a check valve held in the open position by the relief device. The shutoff device will not be rendered inoperative. The recommended procedures for winterizing valves shall be as follows: the valve must be fully closed or fully opened and the body cavity should be purged with a nonreactive gas (for example, nitrogen) or filled with a fluid to produce a solution with a low freezing point.1.1 This practice covers installation, inspection, and maintenance of valve body cavity pressure relief methods for valves used in geothermal and other high-temperature liquid service. The valve type covered by this practice is a design with an isolated body cavity such that when the valve is in either the open or closed position pressure is trapped in the isolated cavity, and there is no provision to relieve the excess pressure internally.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 The purpose of these test methods is to provide reliable and repeatable test methods for the evaluation of stationary exercise bicycles and ergometers assembled and maintained according to the manufacturer’s specifications. Use of these test methods in conjunction with Specifications F1250 and F3021 is intended to ensure appropriate performance and reliability of said equipment and reduce the risk of serious injury from design deficiencies.1.1 These test methods specify procedures and equipment used for testing and evaluating stationary exercise upright and recumbent bicycles and ergometers for compliance to Specification F1250. Both design and operational parameters will be evaluated. Where possible and applicable, accepted test methods from other recognized bodies will be used and referenced. In the case of a conflict between this document and Specification F1250, Specification F1250 takes precedence.1.2 Requirements—Stationary exercise bicycles and ergometers are to be tested for the parameters specified in Specification F2276 and Test Methods F2571 and the following parameters unique to this equipment:1.2.1 Seat post construction and loading,1.2.2 Handlebar construction and loading,1.2.3 Pedal construction and loading,1.2.4 Crank arm and enclosure entrapment,1.2.5 Seat back support loading,1.2.6 Stability,1.2.7 Direct Drive Exercise Bicycle Pedal Endurance,1.2.8 Warnings, and1.2.9 Documentation.1.3 This test method2 contains additional requirements to address the accessibility of the equipment for persons with disabilities.1.4 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The use of the body measurement information in Table 1 and Table 2 will assist manufacturers in developing patterns and garments that are consistent with the current anthropometric characteristics of the population of interest. This practice should in turn reduce or minimize consumer confusion and dissatisfaction related to apparel sizing. (Also refer to ISO 3635.)4.2 Three-dimensional avatars depicting each of the missy sizes and sub category curvy and straight on certain measures, were created by Alvanon, Inc. and included in this standard to assist manufacturers in visualizing the posture, shape, and proportions generated by the measurements charts in the accompanying tables. (Avatar 1-6) See Fig. 1 and Fig. 2.FIG. 1 Missy Avatar - CurvyFIG. 2 Missy Avatar - Straight1.1 These tables list body measurements of adult female misses figure Type sizes 00 through 20. Although these are body measurements, they can be used as a baseline in designing apparel for Missy in this size range when considering such factors as fabric type, ease for body movement, styling, and fit.1.2 These tables list body measurements for the complete range of Missy sizing.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This document represents research methodology and the tables represent charted data from subjects. Some terminology is specific to the research. The data represent the first body measurements ever taken of women aged 55 and older and is not a standard of average current apparel industry practices as represented in all other sizing standards.1.2 These tables list body measurements of adult women age 55 and over. The body measurements tables can be used as a baseline in designing apparel for adult women in this age group, taking into account such factors as fabric type, desired ease of body movement, styling, and fit.1.3 Measurement tables correspond to the figure types and numerical size designations in the PS 42-70 database. Until body measurements of all adult women are updated, companies will have to analyze the older customer's differences by body measurements and proportions instead of hang tag numbers, and adapt them to currently marketed sizes and figure types. Companies especially affected are those who are today using smaller numbered hang tag designations, who offer mainly S, M, and L sizes, or who have adjusted their charts from the PS 42-70 database to reflect the specific body measurements of their 1990's customer.1.4 The values stated in either acceptable SI units or inch-pound units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values.

定价： 0元 / 折扣价： 0 元

1.1 This document represents research methodology and the tables represent charted data from subjects. Some terminology is specific to the research. The data represent the first body measurements ever taken of women aged 55 and older and is not a standard of average current apparel industry practices as represented in all other sizing standards.1.2 These tables list body measurements of adult women age 55 and over. The body measurements tables can be used as a baseline in designing apparel for adult women in this age group, taking into account such factors as fabric type, desired ease of body movement, styling, and fit.1.3 Measurement tables correspond to the figure types and numerical size designations in the PS 42-70 database. Until body measurements of all adult women are updated, companies will have to analyze the older customer's differences by body measurements and proportions instead of hang tag numbers, and adapt them to currently marketed sizes and figure types. Companies especially affected are those who are today using smaller numbered hang tag designations, who offer mainly S, M, and L sizes, or who have adjusted their charts from the PS 42-70 database to reflect the specific body measurements of their 1990's customer.1.4 The values stated in either acceptable SI units or inch-pound units shall be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system must be used independently of the other, without combining values.

定价： 0元 / 折扣价： 0 元

1.1 This specification covers minimum performance criteria and describes test methods for body protectors for use in equine racing in a controlled environment.NOTE 1: It is recognized that it is not possible to write a body protector performance standard that will result in products that can protect against all types of injury or death in an accident.1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at time of development of this specification.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车