1.1 This specification provides the recommended criteria for specifying the construction of barrier systems for restricting access or ensuring human confinement, with the capability of defeating or seriously resisting any breaching attempts.1.2 No recommendation is made or implied as to the merits of the product of any particular manufacturer. Choice of product components selection for the barrier system should be made by the writers of the project based on their own perception of the merits of products for this application.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI values stated in parentheses are provided for information only.

定价： 0元 / 折扣价： 0 元

This specification covers glass fabric impregnated, coated, and sintered on both sides with PTFE to a specified maximum nominal thickness. It does not pertain to structural fabric, single-sided PTFE coatings, or materials used for laminates. The PTFE-coated glass fabric is for electrical, chemical, and mechanical uses. The base material used in the manufacture of the products of this specification shall be a woven glass fabric. The glass fabric is impregnated or coated with polytetrafluoroethylene. When necessary, additives are used to aid the dispersion to achieve the required properties and performance of the final product. The glass fabric shall be tested for color, thickness, breaking strength, edge tear, conductivity, percent PTFE, smoothness, and porosity.1.1 This specification covers glass fabric impregnated, coated, and sintered on both sides with PTFE to a nominal thickness of 0.318 mm (0.015 in.) or less.1.2 The PTFE-coated glass fabric is for electrical, chemical, and mechanical uses.1.3 The PTFE-coated glass fabric of this specification does not pertain to structural fabric, single-sided PTFE coatings, or materials used for laminates.1.4 The values stated in SI units as detailed in IEEE/ASTM SI-10.NOTE 1: There is no ISO standard that covers information included in this specification. The dielectric test is mentioned in ISO 12086-2 and ISO 13000-1 and -2.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 These test methods may be used for acceptance testing of commercial shipments; however, caution is advised because information about between interlaboratory precision is incomplete. Comparative tests as directed in 5.1.1 may be advisable.5.1.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is statistical bias between them using competent statistical assistance. As a minimum, use test samples for such comparative tests that are as homogeneous as possible, drawn from the same lot of material as the samples that resulted in the disparate results during initial testing, and that are randomly assigned in equal numbers to each laboratory for testing. The test results from the laboratories should be compared using statistical test for unpaired data at a probability level chosen prior to the testing series. If a bias is found either its cause must be found and corrected, or future test results for that material must be adjusted in consideration of the known bias.5.2 These test methods are useful to evaluate quality and cost control during the manufacture of pile yarn floor covering.5.3 The significance and uses of particular properties and test methods are discussed in the appropriate sections of the specified test methods.1.1 This guide covers the procedures listed as follows for testing woven, knitted and nonwoven backing fabrics designed for use in the manufacture of pile yarn floor coverings. The procedures appear in the following order:  SectionBow and Skewness of Woven Fabrics  8Breaking Force of Woven and Nonwoven Fabrics 15Breaking Force After Tufting of Woven and Nonwoven Fabrics 16Extractable Matter  9Fabric Count of Woven Fabrics 12Fabric Count of Knitted Fabrics 13Length of Woven Fabrics 11Mass per Unit Area (Weight) of Woven Fabrics 14Width of Woven Fabrics 101.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the physical requirements for aluminum alloy chain link fence fabrics used for commercial, industrial, and residential applications. These fabrics shall meet the specified requirements for weave form, size of mesh, size of wire, height of fabric, selvage, breaking strength, finish, and standard leangth of rolls.1.1 This specification covers aluminum alloy chain link fence fabric for commercial, industrial, and residential uses.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

AbstractThese test methods cover procedures for testing fully cured silicone rubber-coated glass fabric and tapes to be used for electrical insulation. The test procedures for the following test methods are detailed: (1) breaking strength, (2) breaking strength after creasing, (3) dielectric breakdown voltage, (4) dielectric proof voltage, (5) dissipation factor and relative permittivity, (6) thermal endurance, (7) thickness, (8) thread count, (9) volume resistivity, and (10) weight. The procedures for sampling of fabric rolls, fabric sheets, tapes and strips, and test specimen preparation and conditioning are given. The test apparatus, report requirements, and precision and bias for each test are provided. The drum type gripping device and creasing apparatus for breaking strength test are illustrated. Voltage stress test shall be done for dissipation factor and relative permittivity and volume resistivity tests.1.1 These test methods cover procedures for testing fully cured silicone rubber-coated glass fabric and tapes to be used for electrical insulation.1.2 The procedures appear in the following order:Procedure Sections ASTMReferences Breaking Strength  7  D828Breaking Strength After Creasing  8  ...Conditioning  5  ...Dielectric Breakdown Voltage  9  D149, D295,  D6054Dielectric Proof-Voltage  10  D1389Dissipation Factor and Relative Permittivity 11  D150Sampling  4  ...Thermal Endurance 15  D1830Thickness  6  D374Thread Count 14  ...Volume Resistivity 12  D257Weight 13  ...1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 9.5.1 for a specific warning statement.

定价： 0元 / 折扣价： 0 元

4.1 This test method is used to determine the quaternary ammonium salts commonly found in fabric softeners. Quaternary ammonium compounds being the active ingredients in fabric softeners requires accurate determination to assess the cost and performance of such compounds.1.1 This test method describes a potentiometric titration procedure for the determination of quaternary ammonium salts in fabric softeners. This test method is intended for the analysis of known quaternary ammonium salts such as the dialkyl dimethyl quaternary ammonium compound type and the diamidoamine based quaternary ammonium compound type.1.2 The quaternary ammonium salts conform to the structures shown in Fig. 1 and Fig. 2.1.3 The analytical procedure appears in the following order:  SectionApparatus  5Reagents  6Preparation of standard reagents  7Standardization of hyamine solution  9Safety precautions  8Procedure for determination of dialkyl dimethyl quaternaries 10Procedure for determination of diamidoamine based quaternaries 111.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 6.4, 6.6, 6.7 and Section 8 for specific warning statements.

定价： 0元 / 折扣价： 0 元

This specification covers metallic-coated carbon steel wire for the manufacture of chain-link fence fabric and marcelled tension wire. Three coating types, namely: Type I (aluminized), Type II (galvanized), and Type III (zinc-aluminum-mischmetal alloy-coated), and five coating classes, namely: Class 3, Class 4, Class 5, Class 60, and Class 100, are covered. This specification does not cover the wire for chain-link fence when the coating is to be applied after the weaving process. The steel rod from which the wire is to be drawn shall be manufactured by the open-hearth, electric-furnace, or basic-oxygen process. The wire shall be cold-drawn, then metallic-coated at finished size to produce the specified mechanical properties such as breaking strength. Type I and Type III coatings shall be produced by a hot-dip process and Type II coating by either a hot-dip or an electrolytic process. The ingot or pig aluminum to be used for Type I coating shall conform to the impurity limits specified for copper and iron. Requirements for coated wire diameter, coating weight, coating adherence, and methods of chemical analysis and breaking strength test are detailed.1.1 This specification covers metallic-coated carbon steel wire used in the manufacture of chain-link fence fabric and marcelled tension wire. Three types of coatings are covered:1.1.1 Type I—Aluminum-coated (aluminized),1.1.2 Type II—Zinc-coated (galvanized), and1.1.3 Type III—Zinc-5 % Aluminum-Mischmetal (Zn-5Al-MM) alloy-coated.1.2 The chain-link fabric woven from wire in this specification is covered separately by Specifications A491 for Type I, A392 for Type II, and F1345 for Type III.1.3 The marcelled tension wire manufactured from wire in this specification is covered separately in Specifications A824 and F1664.1.4 This specification does not cover the wire used for Specification A392 when the chain-link fence producer applies the coating after the weaving process.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information only.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This terminology covers defects in both woven and knit fabrics. Descriptions of the defects, illustrations, and related material are given under the most frequently used terms; synonym(s) are listed in parentheses and cross referenced.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 The depth of color achieved in dyeing fabric according to this practice is relative to the amount of sizing in the fabric. This practice employs a chromatic staining scale from 1 to 5 which is inversely proportional to the relative amount of sizing in the fabric. A light color stain indicates a low concentration of sizing and warrants a high numerical rating, while a dark color stain indicates a high concentration of sizing and warrants a low numerical rating.5.2 The accuracy of this practice depends upon the ability of the testing personnel to match the color of the stain to the colors in the AATCC 9 Step ChromaticTransference Scale.1.1 Using a color scale of 1 to 5, this practice describes the procedures for determining the presence and relative amount of sizing in fabrics made of undyed nylon or non-cationically dyeable polyester yarns prepared with a cationically dyeable sizing1.2 Procedures and apparatus other than those stated in this standard may be used by agreement of purchaser and supplier with the specific deviations from the standard acknowledged in the report.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification establishes the criteria for polymer privacy insert slats designed for insertion into chain link fabric after the chain link fence installation and privacy chain fabric having slats preinserted into chain link mesh during the chain link weaving process. It covers four types of polymer privacy insert slats: Type P-V consisting of polyethylene privacy insert slats hand inserted vertically into standard mesh chain link fabric after the fence installation; Type P-D consisting of polyethylene privacy insert slats hand woven diagonally into standard mesh chain link fabric after the fence installation; Type F-VDH consisting of modified fiberglass privacy insert slats hand woven, vertically, diagonally or horizontally into standard mesh chain link fabric after the fence installation; and Type PI-V consisting of privacy chain link fabric with vertical high density polyethylene privacy slats pre-inserted into the chain link mesh during the chain link weaving process. The standard addresses ordering information, privacy slat design configurations, weathering, chain link fence framework, tie wires and hog rings, and installation.1.1 This specification covers polymer privacy insert slats designed for insertion into chain link fabric after the chain link fence installation and privacy chain fabric having slats pre-inserted into chain link mesh during the chain link weaving process.1.1.1 Type P-V consists of polyethylene privacy insert slats hand inserted vertically into standard mesh chain link fabric after the fence installation.1.1.2 Type P-D consists of polyethylene privacy insert slats hand woven diagonally into standard mesh chain link fabric after the fence installation.1.1.3 Type F-VDH consists of modified fiberglass privacy insert slats hand woven, vertically, diagonally or horizontally into standard mesh chain link fabric after the fence installation.1.2 Type PI-V consists of privacy chain link fabric containing vertical high density polyethylene privacy slats pre-inserted into the chain link mesh during the chain link weaving process. Style 1a: Wider, 2 3/8 in. [60.3 mm] to 3 in. [76.2 mm] slats, pre-inserted into specially designed larger mesh. Style 1b: Type P-V friction fit slats pre-inserted into standard 2 in. [50 mm] chain link mesh.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the basic physical requirements for steel chain-link fence fabric that are aluminum-coated before weaving. Fabrics conforming to this specification shall meet specified requirements for weave form and typical diamond count, size of mesh, size of wire, height of fabric, selvage, weight of aluminum coating, breaking strength, workmanship and finish, and standard length of rolls.1.1 This specification covers aluminum-coated steel chain-link fence fabric, aluminum-coated before weaving.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method provides for rapid screening of antimicrobial treatments located in or on fabrics and air filter media.5.2 This test method simulates actual use conditions that may occur on fabrics, for example, food and beverage spills; soiling from body contact, that is, body oils, skin cells; prolonged moisture exposure.5.3 This test method provides a means to screen for activity and durability of an antimicrobial treatment under conditions of organic loading.5.4 This test method provides for the simultaneous assessment of multiple fabric components, for example, fabric, component fibers with polymer incorporated treatments, and back coating if present, for antimicrobial activity.5.5 Fabrics or filter media may be cleaned prior to testing with this method in order to assess the durability of the antimicrobial effect.1.1 This test method is designed to evaluate qualitatively the presence of antibacterial and antifungal activity in or on fabrics or air filter media.1.2 Use half-strength (nutrient and agar) tryptic soy agar as the inoculum vehicle for bacteria and half-strength potato dextrose agar as the inoculum vehicle for mold conidia. Use of half-strength agars may reduce undue neutralization of an antimicrobial due to excessive organic load.1.3 This test method permits evaluation, both visually and stereomicroscopically, of the antimicrobial activity of fabric or filter media.1.4 Use this test method to assess the durability of the antimicrobial treatments on new fabric or filter media, and on those repeatedly laundered or exposed to in-use conditions.1.5 This test method may not be suited for covalently bonded (that is, silane-modified quaternary ammonium compounds) or actives with limited migration or solubility.1.6 Knowledge of microbiological techniques is required for the practice of this test method.1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

5.1 Test Method D4032 for testing stiffness of fabrics is considered satisfactory for quality control testing. It may also be used for acceptance testing of commercial shipments since the test method has been used extensively in the trade field. In cases of differences in values reported by purchaser and seller using Test Method D4032 for acceptance testing, the statistical bias, if any, between the laboratories of the purchaser and the seller should be determined with each comparison being based on the testing of specimens taken homogeneously from a lot of material of the type being evaluated. Specimens should be randomly assigned in equal numbers to each of the laboratories.5.2 The circular bend procedure gives a force value related to fabric stiffness, simultaneously averaging stiffness in all directions. The stiffness tests in Test Methods D1388 are of the single directional type.5.3 The circular bend procedure is simple to perform and may be used for knitted, woven, or nonwoven fabrics, provided gage capacity is in keeping with fabric range tested.1.1 This test method covers the determination of the stiffness of fabrics by the circular bend procedure.1.2 This test method is generally applicable to all types of fabrics, including woven, knitted and nonwovens, of any fiber content.NOTE 1: For other methods of testing for stiffness, refer to Test Methods D1388.1.3 The values stated in SI units are to be considered as standard; the values in inch-pound units are included for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This guide identifies test methods used in the process of determining the characteristics of fabrics used to form fine aggregate concrete for properties such as mass, apparent opening size, tensile strength, water permeability and other mechanical properties.4.2 This guide is intended for general use by those who manufacture, specify or install fabric formed concrete (FFC) revetments.4.3 Consult specific ASTM specifications for evaluation criteria.4.3.1 A listing of all ASTM geosynthetic performance specifications may be found in Volume 04.09 of the Annual Book of Standards.1.1 This guide lists ASTM standards available for the testing evaluation of fabrics used to form fine aggregate concrete.1.2 This guide identifies the test methods available to manufacturers, engineers, testing organizations and other related parties.1.3 This guide provides a list of test methods that can be used by the reader to determine the properties of fabric used to form fine aggregate concrete.1.4 This guide is not intended to be used in the establishment of performance criteria, but as a guide for product development and purchasing contracts.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.6 This guide offers an organized collection of information or a series of options and does not recommend a specific course of action. This document cannot replace education or experience and should be used in conjunction with professional judgement. Not all aspects of this guide may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care of which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

定价： 0元 / 折扣价： 0 元

This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication. Welded wire mesh fence fabric is classified in accordance with coating as follows: Type 1; Type 2; Type 3; and Type 4. Tests shall be performed to determine the properties of the material in accordance with the following test methods: metallic coating weight; polymer coating thickness; polymer adhesion test; and weld shear strength of fabric.1.1 This specification covers welded wire mesh fence fabric produced from steel wire or metallic-coated steel wire. The metallic-coated fabric may be polymer coated after fabrication.1.2 Welded wire mesh fence fabric is produced in four types, based on the kind of coating, as described in Section 4.1.3 This specification is applicable to orders in either inch-pound units or SI units. Values stated in either inch-pound or SI units are to be regarded separately as the standard. Within the text, the SI units are shown in brackets. The values in the two systems are not exact equivalents; therefore, each system shall be used independent of the other, without combining values in any way.1.4 This specification references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this specification.1.5 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations proper to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车