1.1 This test method covers the determination of capillary-moisture properties of fine-textured soils as indicated by the moisture content - moisture tension relationships determined by pressure-membrane apparatus using tensions between 1 and 15 atm (101 and 1520 kPa). Moisture tension (matrix suction) is defined as the equivalent negative gage pressure, or suction, in soil moisture. The test result is a moisture content which is a measure of the water retained in the soil subjected to a given soil - water tension (or at an approximately equivalent height above the water table). Note 1--For determination of capillary-moisture relationships of coarse- and medium-textured soils, refer to Test Method D2325. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

AbstractThese test methods establish the standard procedures for determining the hygroscopic moisture (and other matter volatile under the test conditions) in pigments. Method A shall be performed on pigments that do not decompose at a specified temperature. This method shall require the use of a wide-mouth cylindrical glass weighing bottle, an oven, and an analytical balance. Method B, on the other hand, shall be used for pigments that decompose at the same specified temperature. This method shall also need a wide-mouth cylindrical glass weighing bottle, an open-tube manometer, a glass desiccator, an oil vacuum pump, and an analytical balance.1.1 These test methods cover procedures for determining hygroscopic moisture (and other matter volatile under the test conditions) in pigments.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This method is intended to induce property changes associated with end-use conditions, including the effects of solar radiation, moisture, and heat. The exposure used is not intended to simulate the deterioration caused by localized weather phenomena such as atmospheric pollution, biological attack, and saltwater exposure.5.2 The relation between time to failure in an exposure conducted in accordance with this test method and service life in a specific outdoor environment requires determination of an acceleration factor, as defined in Terminology G113. The acceleration factor is material dependent and is only valid if it is based on data from a sufficient number of separate exterior and laboratory-accelerated exposures so that the results used to relate times to failure in each exposure can be analyzed using statistical methods.NOTE 1: An example of a statistical analysis using multiple laboratory and exterior exposures to calculate an acceleration factor is described by J. A. Simms.4 See Practice G151 for more information and additional cautions about the use of acceleration factors.5.2.1 The deterioration curve obtained from the results of this test method enables the user to determine the tendency of a geotextile to deteriorate when exposed to xenon arc radiation, water, and heat.5.3 Variation in results may be expected when operating conditions are varied within the accepted limits of this test method. Its intended use is as a qualitative assessment of the presence of ultraviolet inhibitors, and comparison of that influence between products. However, no inference to the time of stability should be implied by the test results to the relation between time duration and outdoor exposure.NOTE 2: Information on sources of variability and on strategies for addressing variability in the design, execution, and data analysis of laboratory-accelerated exposure tests is found in Guide G141.5.3.1 If it becomes necessary for the purchaser and seller to use this test method for acceptance testing, the statistical bias, if any, between the purchaser's and seller's laboratories should be determined. Such comparison is based on specimens randomly drawn from the sample of geotextile being evaluated.5.3.2 In such cases, at a minimum, the two parties should take a group of test specimens which are as homogeneous as possible, and which are from a lot of material of the type in question. The test specimens should then be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using Student's t-test for unpaired data and an acceptable probability level chosen by the two parties before the testing started. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results in the light of the known bias.1.1 This test method covers the determination of the deterioration in tensile strength of geotextiles by exposure to xenon arc radiation, moisture, and heat.1.2 The light and water exposure apparatus employs a xenon arc light source.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 The result obtained by this test is normally considered to be the moisture content of the leather sample. This result is used to correct all other chemical tests to a moisture-free basis.4.2 Materials that are volatile under these conditions, other than water, may be present in the leather, although their amount in any normal leather would be expected to be a very small percentage of the total volatile matter.4.3 Under the conditions of this test, certain materials in leather, such as protein fiber and chromium tanning salts, may retain moisture. Other materials, such as tannins and oils, may be oxidized. Both of these effects produce negative errors in the moisture determination.4.4 The amount of volatile matter (moisture) released by a given leather varies with (a) degree of grinding of the sample, (b) weight of sample taken, (c) temperature and time of the oven drying, (d) shape of the weighing container, and (e) type of oven (gravity versus mechanical convection) used.4.5 Because of the above unknown errors, the result of this test is a purely arbitrary value for the moisture content of the sample. It is, therefore, essential that the method be followed exactly in order to obtain reproducible results among laboratories. This is particularly true if other chemical analytical tests being performed on the same sample are reported on the moisture-free basis.1.1 This test method covers the determination of volatile matter (moisture) in all types of leather.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 Knowledge of the water content of lubricating oils, additives, and similar products is important in the manufacture, purchase, sale, transfer, or use of such petroleum products to help in predicting their quality and performance characteristics.5.2 For lubricating oils, the presence of water can lead to premature corrosion and wear, an increase in the debris load resulting in diminished lubrication and premature plugging of filters, impedance to the effect of additives, and undesirable support of deleterious bacterial growth.1.1 This test method covers the quantitative determination of water in new and in-service lubricating oils and additives in the range of 10  mg/kg to 100 000 mg/kg (0.001 wt./wt. to 10 % wt./wt.) using a relative humidity (RH) sensor. Methanol, acetonitrile, and other compounds are known to interfere with this test method.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 Warning—Samples tested in this test method can be flammable, explosive, and toxic. Use caution when handling them before and after testing.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车