This standard pertains to electronics wide-band transformers transmitting power within a wide band of frequencies covering typically at least one decade in the frequency spectrum. It is not intended to apply to transformers optimized to operate within a narrow band of frequencies. Transformers used in, or in conjunction with, wire line communication facilities serving power stations are excluded due to the special protection requirements involved. Provision is made for including data for use in… read more the design of feedback amplifiers and control networks, or other circuits in which the knowledge of the transformer amplitude and phase frequency response is needed by the system designer. These transformers are required to transform voltage within specified tolerances of amplitude and phase when operating between specified impedances. Guides to application and test procedures are included. The annexes within this standard contain certain precautions and recommended practices. This standard also pertains to hybrid transformers, primarily used in the telecommunications industry. The hybrid transformer is a wide-band transformer used in a manner which makes it part of a capacitance, resistance, and/or inductance network, and it must have characteristics which permit it to match the network for proper overall performance. read less

定价： 143元 / 折扣价： 122 元

This project defines a serial, full-duplex, asynchronous, 9-pin DTE communications port that follows EIA 574 and related standards. Portions of several standards will be referenced along with specific extensions applying to programmable instruments. The resulting draft will apply to point-to-point instrument systems composed of a measurement, stimulus or interconnect device and an instrumentation controller. It may also apply to certain devices outside the scope of the instrument system… read more environment. The document will cover mechanical, electrical and functional requirements of the interface. read less

定价： 130元 / 折扣价： 111 元

Reliability of HVDC Converter Stations, including stations that are "back-to-back" for connection of AC systems, and DC transmission terminals.

定价： 126元 / 折扣价： 108 元

To assist in providing a uniform method for calculating and measuuring torque pulsations which occur during starting of synchronous motors. Synchronous motors as discussed in this guide specifically refer to salient-pole type motors with wound main field circuits with either a continuous or interrupted amortisseur cage/ In modern installations, direct current is applied to the main field by means of slip rings from a static exciter or by a rotating brushless excitation system to establish synchronous operation.

定价： 126元 / 折扣价： 108 元

The scope of this revision effort is the same as the original scope for Std1284-1994 with the potential addition of an informational annex to document the register model of common PC implementation of IEEE Std 1284-1994.

定价： 170元 / 折扣价： 145 元

This standard covers specifications for common public-key cryptographic techniques, including mathematical primitives for secret value (key) derivation, public-key encryption and digital signatures, and cryptographic schemes based on those primitives. Specifications of related cryptographic parameters, public keys, and private keys are also discussed. Classes of computers and communication systems are not restricted.

定价： 206元 / 折扣价： 176 元

This document provides a set of standard verification tasks for processor-based equipment used in safety critical applications on rail and transit systems. The scope of the standard shall encompass and be limited to processes which verify the level of safety achieved in the implementation of safety critical functions which are required to be fail-safe. It does not address quality assurance or validation processes which also affect the level of overall system safety achieved.

定价： 133元 / 折扣价： 114 元

Research, compile and consolidate information leading to the publication of a standard for a template for message sets for intelligent transportation systems (ITS). The template will provide an overall syntax and structure for ITS message sets.

定价： 141元 / 折扣价： 120 元

Electronic power subsystems is an integral part of any electronic system. They perform the task of power processing, management, and distribution. To develop an IEEE Rec. Practice for electronic power subsystems. It includes parameter definitions, parameter test conditions, and parameter test methods. It is intended for dc, single-phase, or three-phase ac electronic subsystems with power level up to 20 KW, voltage level up to 600 V, and frequency up to 400 Hz.

定价： 138元 / 折扣价： 118 元

Update the withdrawn standard to reflectg new test methods and add necessary theory of test. Update and improve terminology.

定价： 127元 / 折扣价： 108 元

This recommended practice provides a guide for installation, splicing, terminating and field proof testing of cable systems as used in industrial and commercial applications. It is not intended to be a design document. Although many of the problems of installation can be avoided by designing cable layouts with the installation limits of this recommended practice.

定价： 130元 / 折扣价： 111 元

The scope of this project is to update the standard as it relates to present codes and industry practices. In addition, this project will develop guidelines with respect to the installation, testing, operation and maintenance of the conductors and terminations for all heating methods described in IEEE 844.

定价： 138元 / 折扣价： 118 元

This recommended practice applies to utility-interconnected PV power systems operating in parallel with the utility and utilizing static (solid-state) inverters for the conversion of direct current (dc) to alternating current (ac). (This recommended practice does not apply to systems utilizing rotating inverters.) This recommended practice describes specific recommendations for "small" systems, rated at 10 kW or less, such as may be utilized on individual residences. These recommendations will provide greater standardization for these smaller systems, thereby reducing the engineering and design burden on both the PV system installer and the interconnecting utility. "Intermediate" applications, ranging from over 10 kW up to 500 kW, follow the same general guidelines as small systems. Options to have adjustable setpoints or other custom features may be required by the inter-connecting utility, depending on the impact of the PV system on the portion of the utility system to which it is interconnected. "Large" systems, greater than 500 kW, may combine various standardized features as well as custom requirements, depending on the impact of the PV system on the portion of the utility system to which it is interconnected. A greater degree of custom engineering of the utility interface is to be expected as the size of the PV system grows in relation to utility system capacity

定价： 141元 / 折扣价： 120 元

Change title to a recommended practice, revise table 1, add a table to part IV, coordinate the revisions of IEEE 1, 98, and 99 for consistency, review terms and definitions for harmonization with IEC85 and IEC 505-1, revise Foreward.

定价： 123元 / 折扣价： 105 元

To revise and update the standard and to consider inclusion of inverter driven AC induction motors in this standard. To reconcile with other existing international standards, e.g. IEC 349.

定价： 123元 / 折扣价： 105 元