This standard describes the design criteria of the PPS and its interfaces with the Class 1E power system, switchyard, transmission system, and AAC source. Figure 1 is a typical interface diagram of the PPS with related power systems.

定价： 元 加购物车

定价： 元 加购物车

This recommended practice addresses the inductive environment that exists in the vicinity of electric power and wire-line telecommunications systems and the interfering effect that may be produced thereeby; guidance is offered for the control or modification of the environment and the susceptibility of the affected systems in order to maintain an acceptable level of interference. An acceptable level is defined as an amount of steady-state or surge induced longitudinal voltage or current that… read more does not cause a personnel or public safety hazard, damage to cable or equipment, and/or circuit degradation or failure. To aid the user of this recommended practice in calculating induction between power and telecommunication lines, the concept of an interface is developed. This recommended practice permits either party, without need to involve the other, to verify the induction at the interface by use of a probe wire. This recommended practice does not apply to railway signal circuits. read less

定价： 元 加购物车

This standard applies to wires and cables, used principally for power system communications and control purposes, which are located within electric supply locations or are installed within the zone of influence (ZOI) of the power station ground potential rise (GPR), or which may be buried adjacent to electric power transmission and distribution lines. This standard covers the appropriate design requirements, electrical and mechanical parameters, the testing requirements, and the handling… read more procedures for cables that are to be installed and operated in high-voltage environments where they may be subjected to high voltages either by conduction, or induction coupling, or both. Coaxial and fiber optic cables, except for those used in Ethernet applications, are specifically excluded from this standard. read less

定价： 元 加购物车

This guide is primarily concerned with outdoor ac substations, either conventional or gas-insulated. Distribution, transmission, and generating plant substations are included. With proper caution, the methods described herein are also applicable to indoor portions of such substations, or to substations that are wholly indoors. No attempt is made to cover the grounding problems peculiar to dc substations. A quantitative analysis of the effects of lightning surges is also beyond the scope of this guide.

定价： 元 加购物车

This standard contains descriptions of the IEEE 802® standards published by the IEEE for frame-based data networks as well as a reference model (RM) for protocol standards. A specification for the identification of public, private, and standard protocols is included.

定价： 元 加购物车

To refine the Security Assoc. Identifier (SAID) field of the current Standard to support Multicast Key Center (MKC) identification. Neither the SDE PDU format, nor the elements of procedure are changed by this refinement. Additionally, this revision will incorporate supplements 802.10e, 802.10f, 802.10g, and 802.10h.

定价： 元 加购物车

The Internet of Things is predicted to consist of billions of devices by 2020. Many of these devices will run on batteries. To prolong the useful life of these batteries, while making sure devices don t stay in a sleep state too long and run slowly, devices must be able to run in a low-power, low-latency state. Wake-Up Radio, which is being developed by the IEEE 802.11ba working group, offers a solution to this challenge.

定价： 元 加购物车

This standard defines the protocol and compatible interconnection of data communication equipment via a repeater-controlled, star-topology Local Area Network (LAN) using the demand-priority access method.

定价： 元 加购物车

The scope of this project is limited to incorporating the changes between 802-15-1-2002 (Bluetooth specification 1.1) and Bluetooth Specification 1.2 into 802-15-1-2002. The scope of the original project was: To define PHY and MAC specifications for wireless connectivity with fixed, portable and moving devices within or entering a Personal Operating Space (POS). A goal of the WPAN Group will be to achieve a level of interoperability which could allow the transfer of data between a WPAN device… read more and an 802.11 device. A Personal Operating Space (POS) is the space about a person or object that typically extends up to 10 meters in all directions and envelops the person whether stationary or in motion. The proposed WPAN Standard will be developed to ensure coexistence with all 802.11 Networks. read less

定价： 元 加购物车

This standard defines physical layer (PHY) and medium access control (MAC) sublayer specifications for high data rate wireless connectivity (typically over 200 Mb/s) with fixed, portable, and moving devices. Data rates are high enough to satisfy a set of consumer multimedia industry needs, as well as to support emerging wireless switched point-to-point and high-rate close proximity point-to-point applications.

定价： 元 加购物车

This is a standard for short-range, wireless communication in the vicinity of, or inside, a human body (but not limited to humans). It uses existing industrial scientific medical (ISM) bands as well as frequency bands approved by national medical and/or regulatory authorities. Support for quality of service (QoS), extremely low power, and data rates up to 10 Mbps is required while simultaneously complying with strict noninterference guidelines where needed. This standard considers effects on… read more portable antennas due to the presence of a person (varying with male, female, skinny, heavy, etc.), radiation pattern shaping to minimize specific absorption rate (SAR) into the body, and changes in characteristics as a result of the user motions. read less

定价： 元 加购物车

This standard defines PHY and MAC mechanism for Wireless Personal Area Networks (WPAN) Peer Aware Communications (PAC) optimized for peer to peer and infrastructureless communications with fully distributed coordination. PAC features include: discovery for peer information without association, discovery signaling rate typically greater than 100 kbps, discovery of the number of devices in the network, scalable data transmission rates, typically up to 10 Mbps, group communications with… read more simultaneous membership in multiple groups, typically up to 10, relative positioning, multihop relay, security, and operational in selected globally available unlicensed/licensed bands below 11 GHz capable of supporting these requirements. read less

定价： 元 加购物车

This standard defines security key management extensions to address session key generation (both 128-bit and 256-bit key lengths), the creation and/or transport of broadcast/multicast keys, and security algorithm agility. This standard maintains backwards compatibility with IEEE Std 802.15.9-2016.

定价： 元 加购物车

This standard represents the Protocol Implementation Conformance Statement (PICS) Proforma, per ISO/IEC Standard 9646-7 (1995) and ITU-T X.296, for conformance specification of base stations and subscriber stations based upon the WirelessMAN-SC (10-66 GHz) air interface specified in IEEE Std 802.16.

定价： 元 加购物车