定价： 260元 / 折扣价： 221 元 加购物车

定价： 156元 / 折扣价： 133 元

定价： 293元 / 折扣价： 250 元

定价： 605元 / 折扣价： 515 元

定价： 176元 / 折扣价： 150 元

定价： 156元 / 折扣价： 133 元

定价： 156元 / 折扣价： 133 元

定价： 293元 / 折扣价： 250 元

定价： 390元 / 折扣价： 332 元

定价： 176元 / 折扣价： 150 元

定价： 260元 / 折扣价： 221 元

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

4.1 The permissible level of heavy metals in certain coatings is specified by governmental regulatory agencies. This test method provides a fully documented procedure for determining low concentrations of lead present in both water and solvent-reducible coatings to determine compliance.1.1 This test method is intended as a screening test to determine if the solids in a paint contain more than 0.5 % lead. The test described barely detects the presence of 0.4 % but gives a definite positive result at the 0.5 % level.NOTE 1: This test method may be used to detect the presence of lead at concentrations higher or lower than 0.5 % by making appropriate changes in the specimen size and reagent quantities specified.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 Paints giving an unexpected positive or questionable result should be analyzed quantitatively for lead, using Test Method D3335.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in Section 7.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

5.1 This test method is intended for use with other standards that address the collection and preparation of samples (dusts by wipe, dried paint chips, and soils) that are obtained during the assessment or mitigation of lead hazards from buildings and related structures.5.2 Laboratories analyzing samples obtained during the assessment or mitigation of lead hazards from buildings and related structures shall conform to Practice E1583, or shall be recognized for lead analysis as promulgated by authorities having jurisdiction, or both.NOTE 1: In the United States of America, laboratories performing analysis of samples collected during lead-based paint activities are required to be accredited to ISO/IEC 17025 and to other requirements promulgated by the Environmental Protection Agency (EPA).5.3 This test method may also be used to analyze similar samples from other environments such as toxic characteristic extracts of waste sampled using Guide E1908 as prepared for analysis using EPA SW-846 Test Method 1311.1.1 This test method specifies a procedure for analysis of dried paint, soil, and dust wipe samples collected in and around buildings and related structures for lead content using inductively coupled plasma-optical emission spectroscopy (ICP-OES).1.2 This test method should be used by analysts experienced in the use of ICP-OES, the interpretation of spectral and matrix interferences, and procedures for their correction. For determination of lead (Pb) and other metals in air by ICP-OES, see Test Method D7035.1.3 This test method cites specific methods for preparing test solutions of dried paint, soil, and wipe samples for analysis.1.4 It is the user’s responsibility to ensure the validity of this test method for sampling materials of untested matrices.1.5 No detailed operating instructions are provided because of differences among various makes and models of suitable ICP-OES instruments. Instead, the analyst shall follow the instructions provided by the manufacturer of the particular instrument. This test method does not address comparative accuracy of different devices or the precision between instruments of the same make and model.1.6 This test method contains notes that are explanatory and are not part of the mandatory requirements of this test method.1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7.1 Exception—The inch-pound and SI units shown for wipe sampling data are to be individually regarded as standard for wipe sampling data.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车