定价： 0元 / 折扣价： 0 元

定价： 345元 / 折扣价： 294 元

定价： 345元 / 折扣价： 294 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

This standard details the general bomb test method for determination of the amount of sulfur in lubricating oils with additives, additive concentrates, lubricating greases, and other petroleum products with low volatilities. This test method entails oxidizing samples by combustion in a bomb containing oxygen under pressure. The amount of sulfur is determined by gravimetry. Materials needed for the test include a combustion bomb, sample cup, firing wire, ignition circuit, and a cotton wicking or nylon sewing thread. All reagents, samples, and other chemicals used for the test should conform to the required concentration and purity.1.1 This test method covers the determination of sulfur in petroleum products, including lubricating oils containing additives, additive concentrates, and lubricating greases that cannot be burned completely in a wick lamp. The test method is applicable to any petroleum product sufficiently low in volatility that it can be weighed accurately in an open sample boat and containing at least 0.1 % sulfur.NOTE 1: This test method is not applicable to samples containing elements that give residues, other than barium sulfate, which are insoluble in dilute hydrochloric acid and would interfere in the precipitation step. These interfering elements include iron, aluminum, calcium, silicon, and lead which are sometimes present in greases, lube oil additives, or additive oils. Other acid insoluble materials that interfere are silica, molybdenum disulfide, asbestos, mica, and so forth. The test method is not applicable to used oils containing wear metals, and lead or silicates from contamination. Samples that are excluded can be analyzed by Test Method D1552.1.2 This test method is applicable to samples with the sulfur in the range 0.09 % to 5.5 % by mass.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

定价： 702元 / 折扣价： 597 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Trace quantities of sulfur compounds in hydrocarbon products can be harmful to many catalytic chemical processes in which these products are used. Maximum permissible levels of total sulfur are normally included in specifications for such hydrocarbons. It is recommended that this test method be used to provide a basis for agreement between two laboratories when the determination of sulfur in hydrocarbon gases is important.4.2 On liquefied petroleum gas, total volatile sulfur is measured on an injected gas sample. For such material a liquid sample must be used to measure total sulfur.1.1 This test method covers determination of sulfur in the range from 1.5 to 100 mg/kg (ppm by mass) by weight in hydrocarbon products that are gaseous at normal room temperature and pressure.NOTE 1: The test method has been tested cooperatively only on high-purity ethylene gas. Precision data have not been developed for other products.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

5.1 These procedures are used by producers and users of RDF for determining the total sulfur content of the fuel.1.1 These test methods present two alternative procedures for the determination of total sulfur in prepared analysis samples of solid refuse-derived fuel (RDF). Sulfur is included in the ultimate analysis of RDF.1.2 The test methods appear in the following order:Test SectionsEschka Method 8 – 11Bomb Washing Method 12 and 131.3 These test methods may be applicable to any waste material from which a laboratory analysis sample can be prepared.1.4 The values stated in SI units are to be regarded as standard. Inch-pound units are provided for information.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements see Section 6.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车