定价： 689元 / 折扣价： 586 元 加购物车

定价： 689元 / 折扣价： 586 元

定价： 605元 / 折扣价： 515 元 加购物车

定价： 819元 / 折扣价： 697 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 689元 / 折扣价： 586 元

定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

3.1 Membrane switch keys are subjected to repeated actuations, usually by a human finger. This can transfer body oil, hand creams, automotive fluids and so forth. Materials are often subjected to other conditions (for example, wiping, cleaning, rubbing) during handling, end-use, shipment, or storage that may cause abrasion damage. The result may be a significant removal of the coatings, text, or decorative inks.3.2 This test method is applicable to a wide range of materials. The main criterion is that the abrasion process produces visible wear or breakthrough of the surface being tested.3.3 The amount of abrasion damage to a surface is dependent on numerous variables. This test method provides a way of comparing relative abrasion resistance and the effect of chemicals on inks, coatings, and substrates. In no way do the results provide a correlation value of the number of human finger touches before coating failure. It only provides a means to compare results of tests performed using the same equipment, abrasive materials and loading conditions.3.4 The test method can be used for quality control purposes, as a research and development tool, to evaluate material combinations for a given application, or for the comparison of materials with relatively similar properties and the effect of chemicals on the abrasion resistance.1.1 This test method describes the procedure for subjecting inks or coatings on substrates to an abrasive medium, with or without the application of chemicals, at a specified force.1.2 Within certain limitations, as described in this standard, this test method is applicable for materials including, but not limited to: printed or coated polyester, polycarbonate, and silicone rubber. The samples can be either flat or contoured.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

3.1 The maximum length and minimum diameter of the pipe shall be determined by the capacity of the blast equipment used.3.2 This guide is recommended for removing mill scale, rust scale, paints, zincs, and oxides.1.1 This guide covers metallic abrasive blasting to descale the interior of carbon steel pipe.1.2 This guide is recommended for use in conjunction with an abrasive reclamation system.1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车