定价： 689元 / 折扣价： 586 元

5.1 This plate format is useful for the routine monitoring of culturable, waterborne bacteria in potable and non-potable waters. The significance of finding these bacteria can help with identifying water quality or water system problems or evaluate compliance with maintenance protocols. This test method uses small volumes of water, or dilutions thereof, and provides an easy and reliable method that eliminates media preparation and reduces laboratory waste.1.1 This test method describes a simple procedure for the quantification of culturable, waterborne bacteria in potable water (drinking water, bottled water, and dental water, for example) and non-potable waters (cooling towers, for example).1.1.1 The EasyDisc2, 3 plate format is designed to test 1 mL of a water sample on a 47 mm gridded plate containing a growth reagent embedded to the plate’s inner surface.1.1.2 Detection is based on colorimetric technology in which viable, aerobic, heterotrophic, waterborne bacteria grow when present in the water sample, displaying a color reaction which allows for a simplified visualization of colony growth.1.2 Each plate can accurately detect up to 300 colony forming units per 1 mL (CFU/1 mL) of sample. To increase the quantification range, a sample dilution can be used. Adjust the CFU/mL result to reflect dilutions.1.3 This test method can be used for potable (for example, drinking, bottled, and dental) waters and non-potable waters such as cooling tower waters. It is the user’s responsibility to adhere to all requirements by local regulations and ensure the validity of this test method for waters other than those tested as part of the Interlaboratory Study (ILS).1.4 The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 The quantity and quality of the spores produced by this practice may be used to assess environmental surface disinfectants for sporicidal activity (4). The method is applicable to standard as well as clinically isolated toxigenic and non-toxigenic strains of C. difficile.1.1 This practice describes the production and semipurification of C. difficile spores (also called endospores) primarily for use in testing the sporicidal activities of environmental surface disinfectants (Test Methods E2111and E2197); such spores can also be used to study their structure, chemistry and germination.1.2 While the practice described is based on the use of 500-mL volumes of the liquid culture medium in an anaerobic incubator, anaerobic jars with smaller volumes of the same medium can also be used.1.3 It is the responsibility of the investigator to determine whether Good Laboratory Practice (GLP) regulations are required and to follow them when appropriate (40 CFR, Part 160 for EPA submissions and 21 CFR; Part 58 for FDA submissions).1.4 Warning—This standard may involve hazardous materials, chemicals, and microorganisms and should be performed only by persons with formal training in microbiology.1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use in insulated conductor assemblies for electrical purposes. These conductors shall be composed of one or more roller shaped or die closed layers of helically laid wires using the single input wire. For stranded conductors, the direction of lay of the outer layer shall be leeft hand and may be reversed or unidirectional/unilay in successive layers. Test for the physical and electrical properties of wires composing conductors made from hard-drawn or medium-hard-drawn wires, uncoated or coated, shall be made before but not after stranding. For the purpose of calculating mass, cross sections, and so forth, the density of the copper shall be taken. The mass and electrical resistance of a unit length of stranded unsealed conductor are a function of the lenght of lay shall be calculated.1.1 This specification covers stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use in insulated conductor assemblies for electrical purposes. These conductors shall be composed of one or more roller shaped or die closed layers of helically laid wires using the single input wire (SIW) methodology. (see Note 1 and Explanatory Note 1)NOTE 1: Sealed conductors which are intended to prevent longitudinal water propagation and are further covered/insulated, are also permitted within the guidelines of this specification.1.2 The values stated in inch-pound or SI units are to be regarded separately as standard. The values in each system are not exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.2.1 For density, resistivity, and temperature, the values stated in SI units are to be regarded as standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification deals with continuous grain flow carbon and alloy steel crankshaft forgings intended for medium speed diesel and natural gas engines. The steel used in the manufacture of the forgings is required to be vacuum degassed. Heat treatment, which may be done either before or after rough machining, shall consist of normalizing followed by tempering at a subcritical temperature, or austenitizing, liquid quenching and subcritical tempering. Charpy impact and tensile tests, which shall be performed at a frequency of one test per heat treatment load, shall be used to evaluate tensile strength, yield strength, elongation, reduction of area, and Brinell hardness requirements of forgings. Chemical composition requirements shall also be examined by heat analysis. Grain size tests and non-destructive magnetic particle examinations shall be conducted as well. When required by the purchaser, crankshafts may be surface hardened in designated areas for the purposes of enhanced wear resistance and fatigue strength.1.1 This specification covers continuous grain flow forged carbon and alloy steel crankshafts for medium speed diesel and natural gas engines.1.2 The steel used in the manufacture of the forgings is required to be vacuum degassed.1.3 The choice of steel composition grade for a given strength class is normally made by the forging supplier, unless otherwise specified by the purchaser.1.4 Provision is made for treatment of designated surfaces of the crankshaft to provide enhanced fatigue strength, or wear resistance, or both.1.5 Except as specifically required in this specification, all provisions of Specification A788/A788M apply.1.6 Unless the order specifies the applicable “M” specification designation, the material shall be furnished to the inch-pound units.1.7 The values stated in either inch-pound units or SI (metric) units are to be regarded separately as standard. Within the text and tables the SI units are shown in brackets. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

CSA Preface This is the first edition of CAN/CSA-C61000-2-12, Electromagnetic compatibility (EMC) - Part 2-12: Environment - Compatibility levels for low-frequency conducted disturbances and signalling in public medium-voltage power supply systems, whi

定价： 1001元 / 折扣价： 851 元

1.1 This specification covers cutback petroleum asphalts of the medium-curing type for use in the construction and treatment of pavements.1.2 The values stated in SI units or inch-pounds are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of each other. Combining values from the two systems may result in nonconformance with the standard.1.3 The text of this standard references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the general requirements for the Type III cargo bed cover (CBC). The Type III cargo bed cover is a removable general purpose rigid enclosure for the cargo bed of the 2-1/2 ton cargo truck (M35A2), 2-1/2 ton lightweight medium tactical vehicle (LMTV; M1078), and 2-1/2 ton LMTV trailer (M1082). The CBC provides environmental protection and security for mission equipment and items of general transport.1.1 This specification covers the general requirements for the Type III Cargo Bed Cover (CBC). The Type III CBC is a removable general purpose rigid wall enclosure that is mounted on any of the following model 2.5 ton cargo trucks (1) the M35A2 Lightweight Medium Tactical Vehicle (LMTV) and (2) the M1078 LMTV. It can also be mounted on the M1082 LMTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV Cargo Bed Cover is a removable general purpose rigid enclosure for the cargo bed of the M923, 5 Ton Cargo Truck/M1083, 5 Ton Medium Tactical Vehicle (MTV)/M1095, 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport. Materials shall be tested and shall conform to the general requirements such as first article, conformance, operating requirements, support and ownership requirements, environmental requirements, and interface and operability requirements.1.1 This specification covers the general requirements for the Type IV Cargo Bed Cover (CBC). The Type IV CBC is a removable general purpose rigid wall enclosure that is mounted to the following model 5 ton cargo trucks: (1) the M923 Medium Tactical Vehicle (MTV) and (2) the M1083 MTV. It also can be mounted on the M1095 5 Ton MTV Trailer. The CBC provides environmental protection and security for mission equipment and items of general transport.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test required portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory requirements prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification covers standard requirements for bare-concentric-lay stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid wires. The conductors shall be classified as follows: Class AA, Class A, Class B, Class C, and Class D. Sizes, number of wires, and diameter of wires in the various classes of concentric-lay-stranded conductors shall conform to the prescribed requirements. Welds and brazes may be made in rods or in wires prior to final drawing. The completed conductor of varying classes shall conform to the minimum distance required between the joints. Diameters, areas, and mass of concentric-lay-stranded copper conductors shall conform to the prescribed requirements. Physical and electrical tests of conductors stranded of hard-drawn or medium-hard-drawn wires shall be conducted before but not after stranding. The approximate mass and electrical resistance may be determined using the required increments. The material shall also conform to the temperature corrections factor for conductor resistance.1.1 This specification covers bare concentric-lay-stranded conductors made from round copper wires, either uncoated or coated with tin, lead, or lead alloy for general use for electrical purposes. These conductors shall be constructed with a central core surrounded by one or more layers of helically laid wires.NOTE 1: This specification also permits conductors for use as covered or insulated electrical conductors.NOTE 2: Sealed conductors, that are intended to prevent longitudinal water propagation and are further covered/insulated, are also permitted within the guidelines of this specification.1.2 For the purposes of this specification, conductors are classified as follows (Explanatory Note 1 and Note 2):1.2.1 Class AA—For bare conductors usually used in overhead lines.1.2.2 Class A—For conductors to be covered with weather-resistant (weather-proof), slow-burning materials, and for bare conductors where greater flexibility than is afforded by Class AA is required.1.2.3 Class B—For conductors to be insulated with various materials such as rubber, paper, varnished cloth, and so forth, and for the conductors indicated under Class A where greater flexibility is required.1.2.4 Class C and Class D—For conductors where greater flexibility is required than is provided by Class B conductors.1.3 The SI values for density are regarded as the standard. For all other properties, the inch-pound values are to be regarded as standard and the SI units may be approximate.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers tinned hard-drawn and medium-hard-drawn round copper wire for electrical properties. The tinned wire shall be made by coating hard-drawn and medium-hard-drawn copper wire with commercially pure tin. The copper shall be of such quality and purity that the finished product shall have the properties and characteristics prescribed in this specification. The tin coating shall consist of a smooth continuous layer, firmly adhering to the surface of the copper. The wire shall be free from all imperfections not consistent with the best commercial practice. The tinned wire shall conform to the requirements as to the tensile properties prescribed. Tension tests shall be made on representative samples. The elongation of the wire shall be determined as the permanent increase in length due to the breaking of the wire in tension, measured between gage marks. Electrical resistivity shall be determined by resistance measurements made in accordance with the test method prescribed in this specification. The continuity of coating on the wire shall be determined by the sodium polysulfide test. The specimens shall be thoroughly cleaned by immersion in a suitable solvent for the appropriate time required to remove oil or grease from surface; then removed and wiped dry with clean, soft cloth. Mechanical test for adhesion of coating shall be performed. Any cracking or parting of the coating in the area shown by blackening of the copper shall be cause for rejection.1.1 This specification covers tinned hard-drawn and medium-hard-drawn round copper wire for electrical purposes.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.2.1 Exception—For density, resistivity and temperature, the values stated in SI units are to be regarded as standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For hazard statement, see Sections 10 and 13.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 These test methods for the chemical analysis of metals and alloys are primarily intended as referee methods to test such materials for compliance with compositional specifications particularly those under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel, and Related Alloys. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory under appropriate quality control practices such as those described in Guide E882.1.1 These test methods cover the chemical analysis of tool steels and other similar medium- and high-alloy steels having chemical compositions within the following limits:Element Composition Range, %Aluminum   0.005 to 1.5Boron   0.001 to 0.10Carbon   0.03  to 2.50Chromium   0.10  to 14.0Cobalt   0.10  to 14.0Copper   0.01  to 2.0Lead   0.001 to 0.01Manganese   0.10  to 15.00Molybdenum   0.01  to 10.00Nickel   0.02  to 4.00Nitrogen   0.001 to 0.20Phosphorus   0.002 to 0.05Silicon   0.10  to 2.50Sulfur   0.002 to 0.40Tungsten   0.01  to 21.00Vanadium   0.02  to 5.501.2 The test methods in this standard are contained in the sections indicated below:    SectionsCarbon, Total, by the Combustion— Thermal Conductivity Method— Discontinued 1986   125–135Carbon, Total, by the Combustion Gravimetric Method—Discontinued 2012   78–88Chromium by the Atomic Absorption Spectrometry Method (0.006 % to 1.00 %) 174–183Chromium by the Peroxydisulfate Oxidation—Titration Method   (0.10 % to 14.00 %) 184–192Chromium by the Peroxydisulfate-Oxidation Titrimetric Method—Discontinued 1980   117–124Cobalt by the Ion-Exchange— Potentiometric Titration Method     (2 % to 14 %)  52–59Cobalt by the Nitroso-R-Salt  Spectrophotometric Method  (0.10 % to 5.0 %)  60–69Copper by the Neocuproine  Spectrophotometric Method  (0.01 % to 2.00 %) 89–98Copper by the Sulfide Precipitation- Electrodeposition Gravimetric Method   (0.01 % to 2.0 %)  70–77Lead by the Ion-Exchange—Atomic  Absorption Spectrometry Method (0.001 % to 0.01 %) 99–108Manganese by the Periodate  Spectrophotometric Method  (0.10 % to 5.00 %) 9–18Molybdenum by the Ion Exchange– 8-Hydroxyquinoline Gravimetric Method    203–210Molybdenum by the Thiocyanate Spectrophotometric Method  (0.01 % to 1.50 %) 162–173Nickel by the Dimethylglyoxime Gravimetric Method (0.1 % to 4.0 %) 144–151Phosphorus by the Alkalimetric Method  (0.01 % to 0.05 %) 136–143Phosphorus by the Molybdenum Blue  Spectrophotometric Method (0.002 % to 0.05 %) 19–29Silicon by the Gravimetric Method  (0.10 % to 2.50 %) 45–51Sulfur by the Gravimetric Method—Discontinued 1988   29–35Sulfur by the Combustion-Iodate  Titration Method—Discontinued 2012   36–44Sulfur by the Chromatographic Gravimetric Method—Discontinued 1980   109–116Tin by the Solvent Extraction— Atomic Absorption Spectrometry Method (0.002 % to 0.10 %) 152–161Vanadium by the Atomic Absorption Spectrometry Method (0.006 % to 0.15 %) 193–2021.3 Test methods for the determination of carbon and sulfur not included in this standard can be found in Test Methods E1019.1.4 Some of the composition ranges given in 1.1 are too broad to be covered by a single test method and therefore this standard contains multiple test methods for some elements. The user must select the proper test method by matching the information given in the and Interference sections of each test method with the composition of the alloy to be analyzed.1.5 The values stated in SI units are to be regarded as standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific hazards statements are given in Section 6 and in special “Warning” paragraphs throughout these test methods.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 843元 / 折扣价： 717 元 加购物车

3.1 Membrane switch keys are subjected to repeated actuations, usually by a human finger. This can transfer body oil, hand creams, automotive fluids and so forth. Materials are often subjected to other conditions (for example, wiping, cleaning, rubbing) during handling, end-use, shipment, or storage that may cause abrasion damage. The result may be a significant removal of the coatings, text, or decorative inks.3.2 This test method is applicable to a wide range of materials. The main criterion is that the abrasion process produces visible wear or breakthrough of the surface being tested.3.3 The amount of abrasion damage to a surface is dependent on numerous variables. This test method provides a way of comparing relative abrasion resistance and the effect of chemicals on inks, coatings, and substrates. In no way do the results provide a correlation value of the number of human finger touches before coating failure. It only provides a means to compare results of tests performed using the same equipment, abrasive materials and loading conditions.3.4 The test method can be used for quality control purposes, as a research and development tool, to evaluate material combinations for a given application, or for the comparison of materials with relatively similar properties and the effect of chemicals on the abrasion resistance.1.1 This test method describes the procedure for subjecting inks or coatings on substrates to an abrasive medium, with or without the application of chemicals, at a specified force.1.2 Within certain limitations, as described in this standard, this test method is applicable for materials including, but not limited to: printed or coated polyester, polycarbonate, and silicone rubber. The samples can be either flat or contoured.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers steel joint bars of low-carbon, medium-carbon, and high-carbon grades (Grades 1, 2, and 3) for railway applications. Steel shall be made through basic-oxygen or electric-furnace processes and cast through continuous process or in ingots. An analysis of each heat or cast shall be made to determine the percentage compositions of carbon, manganese, phosphorus, and sulfur. Tension test shall also be made to conform to specified tensile strength and elongation values. Guidelines on the dimensions and physical variations of joint bars are given. Inspection, rejection, rehearing, certification, and product marking procedures are cited.1.1 This specification covers steel joint bars for connecting steel rails in mine, industrial, and standard railroad track.1.2 Three grades of joint bars are defined for applications where non-heat treated bars are suitable:1.2.1 Grade 1, low-carbon, primarily for industrial and mine use.1.2.2 Grade 2, medium-carbon, primarily for industrial and mine use.1.2.3 Grade 3, high-carbon, for general use in standard railroad track. They may be used in the production of insulated track joints.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Comparison of brake horsepower developed and of specific fuel consumption rates from engine to engine may be made by use of data based upon a standard for composition of an engine assembly.4.2 The purchaser of the engine assembly will be fully advised of the minimum scope of assembly which the purchaser may rightfully expect to be encompassed by a response to a request for quotation and to be delivered in response to a purchase order unless the engine builder in the proposal or in the offer to sell has clearly advised otherwise.4.3 It will be made apparent to the purchaser that additional auxiliary and accessory equipment will be needed to supplement the defined engine assembly when full consideration is given to the application of the engine assembly as a prime mover in a specific vessel.1.1 This guide covers performance and minimum scope of assembly of all medium speed marine diesel engines intended for main propulsion of single or multiple screw propelled marine vessels or for vessels using other than screw propeller-type main propulsion.1.2 This guide is intended to supplement the regulations of legally constituted regulating authorities. In the event of any conflict, which may become apparent after publication of this guide, with such legally constituted regulations, the latter shall take precedence, as may be applicable within the jurisdiction of such authorities and specific to each case, unless such latter regulations are formally waived by proper cognizant authority.1.3 This guide is not intended to relieve the purchaser of the obligation fully to advise the engine builder of all of the purchaser’s unique operational considerations to allow those considerations to be satisfied.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车