定价： 338元 / 折扣价： 288 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipes made to Schedule 40 iron pipe sizes (IPS) with concentric inner and outer solid ABS layers and a closed-cell cellular ABS core. The ABS plastics used to make the pipes shall only be either virgin or reworked as specfieid. Reprocessed or recycled plastics are excluded from this specification. The pipes shall meet specified requirements for dimension such as outside diameter, wall thickness, and length; and for performance such as pipe stiffness, lower confidence limit, flattening resistance, impact strength, bond strength, pigments or screening agents, and solvent cement.1.1 This specification covers coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe made to Schedule 40 iron pipe sizes (IPS) and produced by the coextrusion process with concentric inner and outer solid ABS layers and the core consisting of closed-cell cellular ABS. Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers.1.2 Fittings suitable for use with pipe meeting the requirements of this specification are given in Annex A1. Fittings meeting the requirement of Specification D2661 are also acceptable.1.3 Acrylonitrile-butadiene-styrene plastic which does not meet the definitions of virgin ABS plastic as given in 3.2.4 is excluded, as performance of plastic other than those defined as virgin was not determined. ABS rework plastic which meets the requirements of rework plastic as given in 5.3 is acceptable.1.4 Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded.1.5 Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3, respectively.1.6 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.7 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

4.1 The bound styrene test is a measure of the bound monomeric composition of the rubber. It is used as a check on the accuracy of monomer charging and also as a guide to the uniformity of the product, since the bound styrene content affects the physical properties.1.1 This test method covers the determination of styrene content, and is intended for general use on solid uncompounded styrene-butadiene copolymers, commonly referred to as SBR, prepared by the emulsion process. SBR polymers prepared in solution will require the use of different refractive index tables because the vinyl content of the butadiene differs from that in the emulsion polymers. It is applicable to polymers having less than 55 % bound styrene.NOTE 1: The nomenclature used in this test method is in accordance with Practice D1418.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

4.1 A measurement of the residual acrylonitrile in nitrile rubbers (NBR), styrene-acrylonitrile copolymers or ABS terpolymers will determine the polymer's suitability for various applications.4.2 Under optimum conditions, the minimum level of detection of RAN in NBR, SAN, or ABS terpolymers is approximately 50 ppb.1.1 This test method covers the determination of the residual acrylonitrile (RAN) content in nitrile-butadiene rubbers (NBR), styrene-acrylonitrile (SAN) copolymers, and rubber-modified acrylonitrile-butadiene-styrene (ABS) resins.1.2 Any components that can generate acrylonitrile in the headspace procedure will constitute an interference. The presence of 3-hydroxypropionitrile in latices limits this procedure to dry rubbers and resins.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 6.3 and 6.4.NOTE 1: There is no known ISO equivalent to this standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers fiberglass reinforced bituminous sheet materials modified by styrene-butadiene-styrene (SBS) thermoplastic elastomer, and are surfaced with a factory applied continuous metal foil. These materials are intended for use in the fabrication of multiple ply roofing and waterproofing membranes and flashings. This is intended as a material specification only, and does not address specific roof constructions or application techniques. The specified tests and property limits are intended to establish minimum properties. Roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, and others are factors beyond the scope of this specification. The properties for which the materials shall be tested on and consequently conform to are thickness, net mass per unit, back surface coating thickness, peak load value, elongation at peak load, ultimate elongation, tensile-tear strength, low-temperature flexibility, dimensional stability, compound stability, cyclic thermal shock, water absorption, and moisture content.1.1 This specification covers fiberglass reinforced modified bituminous sheet materials that use styrene-butadiene-styrene (SBS) thermoplastic elastomer as the primary modifier and are surfaced with a factory applied continuous metal foil. These materials are intended for use in the fabrication of multiple ply roofing and waterproofing membranes and flashings.1.2 This specification is intended as a material specification only. Questions regarding the suitability of the specific roof constructions or application techniques are beyond the scope of this specification.1.3 The specified tests and property limits are intended to establish minimum properties. In place roof system design criteria such as fire resistance, field strength, impact/puncture resistance, material compatibility, uplift resistance, and others, are factors beyond the scope of this specification.1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.5 The following precautionary statement pertains to the test method portion only, Section 8 of this Specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Due to the inherent danger of peroxides in butadiene, specification limits are usually set for their presence. This test method will provide values that can be used to determine the peroxide content of a sample of commercial butadiene.4.2 Butadiene polyperoxide is a very dangerous product of the reaction between butadiene and oxygen that can occur. The peroxide has been reported to be the cause of some violent explosions in vessels that are used to store butadiene.1.1 This test method covers the determination of peroxides in butadiene.1.2 This test method covers the concentrations range of 1 mg/kg to 10 mg/kg as available oxygen.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The trace hydrocarbon compounds listed can have an effect in the commercial use of butadiene. This test method is suitable for use in process quality control and in setting specifications.1.1 This test method covers the determination of butadiene-1,3 purity and impurities such as propane, propylene, isobutane, n-butane, butene-1, isobutylene, propadiene, trans-butene-2, cis-butene-2, butadiene-1,2, pentadiene-1,4, and, methyl, dimethyl, ethyl, and vinyl acetylene in polymerization grade butadiene by gas chromatography. Impurities including butadiene dimer, carbonyls, inhibitor, and residue are measured by appropriate ASTM procedures and the results used to normalize the component distribution obtained by chromatography.NOTE 1: Other impurities present in commercial butadiene must be calibrated and analyzed. Other impurities were not tested in the cooperative work on this test method.NOTE 2: This test method can be used to check for pentadiene-1,4 and other C5s instead of Test Method D1088.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific warning statements, see 6.1 and 9.3.1.3.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This guide is intended to provide information on the possible composition of 1,3-butadiene products and possible ways to test them. Since there are currently not enough ASTM standards for determining all components of interest, this guide provides information on other potentially available test methods.4.2 Although this guide is not to be used for specifications, it can provide a starting point for parties to develop mutually agreed-upon specifications that meet their respective requirements. It can also be used as a starting point in finding suitable test methods for 1,3-butadiene components.1.1 This guide covers the analysis of 1,3–butadiene products produced in North America. It includes possible components and test methods, both ASTM and other, either actually used or believed to be in use, to test for these components. This guide is not intended to be used or construed as a set of specifications for butadiene products.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车