定价： 590元 加购物车

定价： 590元 加购物车

1.1 This specification covers the performance requirements of CPVC pipe, fittings and solvent cements used in chemical waste drainage systems.1.2 A system is made up of pipe, fittings and solvent cement that meet the requirements of this standard.NOTE 1: Consult the manufacturer’s chemical resistance recommendations for chemical waste drainage applications prior to use.1.3 The text of this specification references notes, footnotes and appendices that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.1.4 The pressure tests described in this standard are laboratory hydrostatic tests that are intended to verify joint/system integrity. They are not intended for use as field tests of installed systems.1.5 Due to inherent hazards associated with testing components and systems with compressed air or other compressed gases, no such testing shall be done unless the component manufacturer gives approval in writing.NOTE 2: Pressurized (compressed) air or other compressed gases contain large amounts of stored energy, which present serious safety hazards should a system fail for any reason.1.6 Mechanical joints used for joining pipe and fittings of different materials are provided for in this specification. They include common flanges, couplings, and unions.1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.NOTE 3: This specification specifies dimensional, performance, and test requirements for fluid handling applications but does not address venting of combustion gases.1.8 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 590元 加购物车

定价： 590元 加购物车

定价： 590元 加购物车

定价： 590元 加购物车

定价： 590元 加购物车

定价： 646元 加购物车

This specification establishes requirements for rigid poly(vinyl chloride) siding with integral foam plastic backing. The poly(vinyl chloride) compound shall be extruded into siding and compounded so as to provide heat stability and weather exposure stability. Tests shall be performed on the vinyl siding, exclusive of any backing material, to determine compliance with length and width, thickness, camber, heat shrinkage, impact resistance, coefficient of linear expansion, gloss, color, and color uniformity requirements. The backed vinyl siding with the backing material shall also undergo testing to ascertain conformance to the following requirements: surface distortion, weatherability, windload resistance, and nail slot allowance for thermal expansion.1.1 This specification establishes requirements for vinyl siding with integral foam plastic backing, where the siding is manufactured from rigid PVC compound. Performance requirements and test methods addressed by this standard include materials properties and dimensions, warp, shrinkage, impact strength, expansion, appearance, and wind load resistance. Methods of indicating compliance with this specification are also provided.NOTE 1: Backed vinyl siding is composed of two major components: the siding and the backing. It is intended that the siding portion comply with Specification D3679. Applicable portions of Specification D3679 are included in this specification. Additional requirements that pertain only to the backing as a separate material, or to the combination of siding and backing as a whole, are also included.1.2 Backed vinyl siding shall be tested with the backing material in place or removed, as specified in the applicable requirement or test method.1.3 The use of PVC recycled plastic in this product shall be in accordance with the requirements in Section 4.1.4 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made to the manufacturer's installation instructions for the specific product to be installed.NOTE 2: Information with regard to siding maintenance shall be obtained from the manufacturer.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.NOTE 3: There is no known ISO equivalent to this standard.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

定价： 646元 加购物车

定价： 571元 加购物车

定价： 590元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车