定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers seamless nickel alloy tubing for use in mechanical applications or as hollow bar for use in the production of hollow components such as, but not limited to, nozzles, reducers, and couplings by machining where corrosion-resistant or high-temperature strength is needed. The grades covered are listed in Table 1. 1.2 This specification covers seamless cold-finished mechanical tubing and hollow bar, and seamless hot-finished mechanical tubing and hollow bar in sizes up to 123/4 in. [325 mm] in outside nominal diameter (for round tubing) with wall thicknesses or inside diameters as required. 1.3 Optional supplementary requirements are provided and when desired, shall be stated in the order. 1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 646元 / 折扣价： 550 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers seamless annealed or cold-worked, austenitic or martensitic stainless steel tubing of 0.100 to 1.0 in. [2.5 to 25 mm] outside diameter with wall thickness of 0.050 in. [1.3 mm] or less for use at high temperature in liquid metal-cooled reactor plants.1.2 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.1.3 This specification and the applicable material specifications are expressed in both inch-pound and SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished in inch-pound units.

定价： 0元 / 折扣价： 0 元

定价： 590元 / 折扣价： 502 元 加购物车

定价： 646元 / 折扣价： 550 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers hot or cold-finished seamless pipes made from NUS N06333 alloy that is intended for heat and corrosion resistance applications. The chemical composition, dimensions and mechanical properties for the welded pipes should be in accordance with those contained in this document and other ASTM documents specified herein.1.1 This specification covers alloy N06333 in the form of hot-finished and cold-finished seamless pipe and tube intended for heat-resisting applications and general corrosive service. The general requirements for pipe and tube are covered in Specification B829.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers seamless round and rectangular including square copper alloy tube in straight lengths. The following copper alloys are specified and classified according to their nominal compositions: UNS No. C22000, UNS No. C23000, UNS No. C26000, UNS No. C27000, UNS No. C27200, UNS No. C27400, UNS No. C28000, UNS No. C33000, UNS No. C33200, UNS No. C37000, and UNS No. C44300. The tempers of drawn tube shall be designated as light-drawn (H55), drawn (H58), and hard-drawn (H80). Light-drawn (bending) temper is used only when a tube of some stiffness but yet capable of being bent is needed. Drawn temper is for general purposes and is most commonly used where there is no specific requirement for high strength on the one hand or for bending qualities on the other. Hard-drawn temper is used only where there is need for a tube as strong as is commercially feasible for the sizes indicated. For any combination of diameter and wall thickness not covered under hard-drawn temper, the values given for drawn temper shall be used. The tempers of annealed tube shall be designated as light anneal (O50) and soft anneal (O60). The tubes shall undergo mechanical tests such as tension test, Rockwell hardness test, and expansion test in order to determine certain properties such as tensile strength and hardness. A mercury nitrate test shall be done to detect and remove mercury vapor. Nondestructive tests such as eddy-current test, hydrostatic test, and pneumatic test shall be done as well.1.1 This specification covers seamless round and rectangular including square copper alloy tube in straight lengths. Ten alloys are specified having the following nominal compositions:Copper Previously Nominal Composition, %Alloy Used        UNS No.2 DesignationA Copper Zinc Lead Tin         C22000 7 90.0 10.0 ... ...C23000 1 85.0 15.0 ... ...C26000 2 70.0 30.0 ... ...C27000 9 65.0 35.0 ... ...C27200 8 63.0 37.0 ... ...C27400 ... 62.5 37.5 ... ...C28000 5 60.0 40.0 ... ...C33000 3 66.0 33.5 0.5 ...C33200 4 66.0 32.4 1.6 ...C37000 6 60.0 39.0 1.0 ...C44300 ... 71.5 27.5 ... 1.00(A) Alloy Designations of Specification B135 – 63, which was published in the 1966 Book of ASTM Standards, Part 5.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 Warning—Mercury has been designated by many regulatory agencies as a hazardous substance that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law. (See 10.1.)21.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车