定价： 1058元 加购物车

定价： 712元 加购物车

4.1 This guide is intended to provide information on the possible composition of 1,3-butadiene products and possible ways to test them. Since there are currently not enough ASTM standards for determining all components of interest, this guide provides information on other potentially available test methods.4.2 Although this guide is not to be used for specifications, it can provide a starting point for parties to develop mutually agreed-upon specifications that meet their respective requirements. It can also be used as a starting point in finding suitable test methods for 1,3-butadiene components.1.1 This guide covers the analysis of 1,3–butadiene products produced in North America. It includes possible components and test methods, both ASTM and other, either actually used or believed to be in use, to test for these components. This guide is not intended to be used or construed as a set of specifications for butadiene products.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 983元 加购物车

4.1 Purpose—This publication establishes lot or batch sampling plans and procedures for inspection by attributes. This publication shall not be interpreted to supersede or conflict with any contractual requirements. The words “accept,” “acceptance,” “acceptable,” etc, refer only to the contractor’s use of the sampling plans contained in this standard and do not imply an agreement by the customer (formerly “Government” in original text) to accept any product. Determination of acceptability by the customer shall be as described in contractual documents. The sampling plans described in this standard are applicable to AQL’s of 0.01 % or higher and are therefore not suitable for applications where quality levels in the range of parts per million levels can be realized.4.2 Application—Sampling plans designated in this publication are applicable, but not limited, to inspection of the following: (1) end items, (2) components and raw materials, (3) operations or services, (4) materials in process, (5) supplies in storage, (6) maintenance operations, (7) data or records, (8) administrative procedures. These plans are intended primarily to be used for a continuing series of lots or batches. The plans may also be used for the inspection of isolated lots or batches, but, in this latter case, the user is cautioned to consult the operating characteristic curves to find a plan which will yield the desired protection (see 6.11).AbstractThis practice establishes lot or batch sampling plans and procedures for inspection by attributes using MIL-STD-105E as a basis for sampling a steady stream of lots indexed by acceptance quality limit (AQL). It provides the sampling plans of MIL-STD-105E in ASTM format for use by ASTM committees and others and recognizes the continuing usage of MIL-STD-105E in industries supported by ASTM. This practice also establishes lot or batch sampling plans and procedures for inspection by attributes.1.1 This practice establishes lot or batch sampling plans and procedures for inspection by attributes using MIL-STD-105E as a basis for sampling a steady stream of lots indexed by acceptance quality limit (AQL).1.2 This practice provides the sampling plans of MIL-STD-105E in ASTM format for use by ASTM committees and others. It recognizes the continuing usage of MIL-STD-105E in industries supported by ASTM. Most of the original text in MIL-STD-105E is preserved in Sections 4 – 6 of this practice.1.3 No system of units is specified in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 983元 加购物车

5.1 This practice was prepared to meet a growing need for the use of standard sampling plans for inspection by variables in customer procurement, supply and storage, and maintenance inspection operations. The variables sampling plans apply to a single quality characteristic which can be measured on a continuous scale, and for which quality is expressed in terms of percent defective. The theory underlying the development of the variables sampling plans, including the operating characteristic curves, assumes that measurements of the quality characteristic are independent, identically distributed normal random variables.5.2 In comparison with attributes sampling plans, variables sampling plans have the advantage of usually resulting in considerable savings in sample size for comparable assurance as to the correctness of decisions in judging a single quality characteristic, or for the same sample size, greater assurance is obtained using variables plans. Attributes sampling plans have the advantage of greater simplicity, of being applicable to either single or multiple quality characteristics, and of requiring no knowledge about the distribution of the continuous measurements of any of the quality characteristics.5.3 It is important to note that variables sampling plans are not to be used indiscriminately, simply because it is possible to obtain variables measurement data. In considering applications where the normality or independence assumptions may be questioned, the user is advised to consult his technical agency to determine the feasibility of application.5.4 Application—Sampling plans designated in this publication are applicable, but not limited, to inspection of the following: (1) end items, (2) components and raw materials, (3) operations or services, (4) materials in process, (5) supplies in storage, (6) maintenance operations, (7) data or records, and (8) administrative procedures.AbstractThis practice establishes lot or batch sampling plans and procedures for inspection by variables using MIL-STD-414 as a basis for sampling a steady stream of lots indexed by AQL. This practice was prepared to meet a growing need for the use of standard sampling plans for inspection by variables in customer procurement, supply and storage, and maintenance inspection operations. The variables sampling plans apply to a single quality characteristic which can be measured on a continuous scale, and for which quality is expressed in terms of percent defective. The theory underlying the development of the variables sampling plans, including the operating characteristic curves, assumes that measurements of the quality characteristic are independent, identically distributed normal random variables.1.1 Purpose—This practice establishes lot or batch sampling plans and procedures for inspection by variables using MIL-STD-414 as a basis for sampling a steady stream of lots indexed by AQL.1.2 This practice provides the sampling plans of MIL-STD-414 in ASTM format for use by ASTM committees and others. It recognizes the continuing usage of MIL-STD-414 in industries supported by ASTM. Most of the original text in MIL-STD-414 is preserved in Sections 6 – 9 of this practice.1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 1058元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

5.1 This test method is used to document the ability of a solid waste resource recovery separator to capture the component(s) of interest in the desired process stream.5.2 The recovery determined in this way is used in conjunction with the purity of the product, as described in Test Method E889.1.1 This test method covers the determination of the recovery of a desired product in a device processing solid waste for the purpose of concentrating a component of interest. The recovery is determined with respect to the amount of the desired component in one output stream (accepts) as opposed to another output stream (rejects). The results of this calculation determine the effectiveness of component separation when coupled with a measure of product purity as described in Test Method E889.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in Section 6.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 571元 加购物车

定价： 646元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车