定价： 646元 加购物车

5.1 This test method provides statistical (and graphical) information concerning floor surface profiles.5.2 Results of this test method are used primarily to:5.2.1 Establish compliance of randomly trafficked floor surfaces with specified FF Flatness and FL Levelness tolerances,5.2.2 Evaluate the effect of different construction methods on resulting floor surface flatness and levelness, and5.2.3 Investigate the curling and deflection of floor surfaces.5.3 Results of this test method shall not be used to enforce contract flatness and levelness tolerances on those floor installations primarily intended to support the operation of fixed-path vehicle systems (for example, narrow aisle warehouse floors).NOTE 2: When the traffic patterns across a floor are random, (as is generally the case) evaluation of the floor's FF Flatness and FL Levelness will necessarily involve a random sampling of the surface, since all of the infinite potential profiles to be seen by the traffic can not possibly be measured. In those instances when the traffic across a floor will be confined to specific paths, however, the requirement for random sampling is eliminated, since the floor can indeed be inspected exactly as it will be seen by all of the traffic. In these special cases, rather than inferring the condition of the traffic paths from a random sample, it is far more useful to measure each of the traffic paths directly using continuous recording floor profilometer configured to run exactly in the traffic wheel paths. Such direct simulation measurements eliminate the inherent uncertainties of statistical sampling and provide profile information immediately applicable to the correction of the surface in way of the future traffic.1.1 This test method covers a quantitative method of measuring floor surface profiles to obtain estimates of the floor's characteristic FF Flatness and FL Levelness Face Floor Profile Numbers (F-Numbers) using the inch-pound system of units.NOTE 1: A complete metric companion to Test Method E1155 has been developed, Test Method E1155M; therefore, no metric equivalents are shown in this test method.1.2 The text of this test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.1.3 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 712元 加购物车

定价： 927元 加购物车

定价： 590元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

定价： 590元 加购物车

定价： 712元 加购物车

定价： 1302元 加购物车

定价： 712元 加购物车

5.1 Although this practice is intended for the collection of dried paint samples in and around buildings for the subsequent determination of lead content, this practice may also be used to collect paint samples from other structures for lead analysis.35.2 The variability associated with the sampling of dried paint is generally considered to be far higher than the variability associated with the analyses of the paint specimens. Therefore, it is essential that sample collection be properly controlled to produce representative and meaningful samples.5.3 These samples are collected in a manner that will permit subsequent digestion using sample preparation techniques such as Practices E1645 or E1979 and determination of lead using laboratory analysis techniques such as inductively coupled plasma atomic emission spectrometry (ICP-AES) (see Test Method E3203) or flame atomic absorption spectrometry (FAAS) (see Test Method E3193).1.1 This practice covers the collection of samples of dried paint and other coatings from buildings.1.2 This practice is used to collect samples for subsequent determination of lead on an area basis (milligrams of lead per area sampled) or concentration basis (milligrams of lead per gram of dried paint collected or mass percent of lead in the paint sample collected).1.3 This practice does not address the sampling design criteria (that is, sampling plan that includes the number and location of samples) that are used for risk assessment and other lead hazard activities. See Guide E2115 or Practices E2271/E2271M or E3074/E3074M.1.4 This practice contains notes that are explanatory and are not part of the mandatory requirements of this practice.1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 7.4.1.1.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车