定价： 0元 / 折扣价： 0 元 加购物车

AbstractThese test methods establish the standard procedures for determining the hygroscopic moisture (and other matter volatile under the test conditions) in pigments. Method A shall be performed on pigments that do not decompose at a specified temperature. This method shall require the use of a wide-mouth cylindrical glass weighing bottle, an oven, and an analytical balance. Method B, on the other hand, shall be used for pigments that decompose at the same specified temperature. This method shall also need a wide-mouth cylindrical glass weighing bottle, an open-tube manometer, a glass desiccator, an oil vacuum pump, and an analytical balance.1.1 These test methods cover procedures for determining hygroscopic moisture (and other matter volatile under the test conditions) in pigments.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The result obtained by this test is normally considered to be the moisture content of the leather sample. This result is used to correct all other chemical tests to a moisture-free basis.4.2 Materials that are volatile under these conditions, other than water, may be present in the leather, although their amount in any normal leather would be expected to be a very small percentage of the total volatile matter.4.3 Under the conditions of this test, certain materials in leather, such as protein fiber and chromium tanning salts, may retain moisture. Other materials, such as tannins and oils, may be oxidized. Both of these effects produce negative errors in the moisture determination.4.4 The amount of volatile matter (moisture) released by a given leather varies with (a) degree of grinding of the sample, (b) weight of sample taken, (c) temperature and time of the oven drying, (d) shape of the weighing container, and (e) type of oven (gravity versus mechanical convection) used.4.5 Because of the above unknown errors, the result of this test is a purely arbitrary value for the moisture content of the sample. It is, therefore, essential that the method be followed exactly in order to obtain reproducible results among laboratories. This is particularly true if other chemical analytical tests being performed on the same sample are reported on the moisture-free basis.1.1 This test method covers the determination of volatile matter (moisture) in all types of leather.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

5.1 Volatile matter, when determined as herein described, can be used to establish the rank of coals, to indicate coke yield on carbonization process, to provide the basis for purchasing and selling, or to establish burning characteristics.1.1 This test method covers the determination of the gaseous products, exclusive of moisture vapor, as volatile matter in the analysis sample of coal or coke from coal.1.2 The test method for the determination of volatile matter is empirical.1.3 Units—The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

2.1 Nonvolatile matter determination is useful as a quality control test, when used in conjunction with other tests, to assure specification compliance.1.1 This test method covers the determination of nonvolatile matter (total solids) in a water-emulsion, organic solvent-based liquid and paste floor polishes, and polymer-emulsion-type floor polishes.1.2 This test method recognizes that the products may contain material that will slowly volatilize or change chemically with a resulting change in weight of the nonvolatile matter. Therefore, since drying to constant weight is impractical, specific drying times have been selected.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method is used to demonstrate compliance with state, EPA as well as relevant international regulations for PM emissions from light-duty vehicles.5.1.1 The EPA Tier 3 and CARB LEV III regulations specify FTP and SFTP PM emission standards for light-duty vehicles.1.1 This test method covers a procedure for the gravimetric determination of particulate matter (PM) collected from diluted light duty vehicle exhaust. It is applicable to mass rates from 0.32 to 32 mg/km (0.2 to 20 mg/mile).1.2 Diluted exhaust is passed through pre-weighed filter media which is re-weighed after sampling. The difference in weight is used to determine particulate mass, which is then used with other data to calculate the distance specific emissions.1.3 The particulate materials that are measured using this test method are generated by a vehicle following the PM standard applicable portions of the United States Environmental Protection Agency (EPA) and California Air Resources Board (CARB) driving schedules and test procedures for determining the emissions of light duty vehicles. For other jurisdictions, consult regional regulations for applicability of these test procedures. These test procedures are referenced in Annex A3 of this document.1.4 The primary intent of this test method is to summarize the PM measurement test procedures as defined by the EPA and CARB (40 CFR Parts §1066, §1065, §86.101, and CARB test procedures for hybrid vehicle testing).NOTE 1: Some requirements are generalized from core references for simplicity and to provide guidance for users applying the principals in this standard to regions not governed by EPA and CARB regulation. For specific details, reference the regulated procedures.1.5 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车