定价： 590元 加购物车

定价： 646元 加购物车

定价： 590元 加购物车

定价： 571元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

1.1 This specification covers aluminum and aluminum-alloy extruded bars, rods, wires, profiles, and tubes in the aluminum alloys (Note 1) and tempers shown in Table 2. Note 1: Throughout this specification the use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: For rolled or cold-finished bars and rods refer to Specification B211/B211M, for drawn seamless tube used in pressure applications, Specification B210/B210M, for structural pipe and tube, Specification B429/B429M, and for seamless pipe and tube used in pressure applications, Specification B241/B241M. Note 3: Pipe and tube products listed in this specification are intended for general purpose applications. This specification may not address the manufacturing processes, integrity testing, and verification required for fluid-carrying applications involving pressure. See Specification B210/B210M, B241/B241M, or both as appropriate for seamless pipe and tube used in fluid-carrying applications involving pressure. See Specification B234M, as appropriate, for use in surface condensers, evaporators, and heat exchangers. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for Aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 This specification is the metric counterpart of Specification B221. 1.5 The values stated in SI are to be regarded as standard. No other units of measurement are included in this specification. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

This specification covers aluminum and aluminum-alloy die forgings, hand forgings, and rolled ring forgings and includes the following UNS alloy designations: A91100, A92014, A92018, A92025, A92219, A92618, A93003, A94032, A95083, A96061, A96066, A96151, A97049, A97050, A97075, A97076, and A97175. Tempers covered by this specification includes: H112, T4, T6, T61, T73, T74, T7352, T7452, T7454, T652, T852, and H111 as well as F and 01 types. The forgings may be manufactured by pressing, hammering, or rolling, at the option of the producer. Requirements for quality assurance, chemical analysis, tension and hardness tests, heat treatment, heat-treat response, and stress corrosion resistance and stress-corrosion cracking test are detailed. The forgings shall conform to the chemical composition requirements prescribed for aluminum, silicon, iron, copper, manganese, magnesium, chromium, nickel, zinc, zirconium, and titanium. Forgings having the specified thickness shall meet the requirements specified for the mechanical properties such as tensile strength, yield strength, elongation, and Brinell hardness. 1.1 This specification2 covers aluminum-alloy (Note 1) die forgings, hand forgings, and rolled ring forgings as shown in Table 2, Table 3, and Table 4 in Section 10 for heat-treatable alloy forgings supplied in the F and 01 tempers. The maximum thicknesses for forgings within the scope of this specification are as indicated in those tables. Note 1: Throughout this specification use of the term alloy in the general sense includes aluminum as well as aluminum alloy. Note 2: For forging stock supplied as rolled, cold-finished bar, extruded bar, or rod see Specification B211/B211M. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91100 for aluminum 1100 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 This specification is the inch-pound companion to Specification B247M; therefore, no SI equivalents are presented in the specification. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

1.1 This specification covers aluminum and aluminum-alloy drawn tube and drawnpipe in straight lengths and tube in coils for general purpose applications and climate control (HVAC) in the alloys (Note 2) and tempers shown in Tables 1-3. Coiled tubes are generally available only as round tubes with a wall thickness not exceeding 0.083 in. [2.00 mm] and only in non-heat-treatable alloys. Note 1: For drawn seamless tubes, see Specification B210/B210M, for drawn seamless tubes to be used in condensers and heat exchangers, Specifications B234 and B234M, and for seamless pipe and tube, Specification B241/B241M. For extruded structural tube and pipe, see Specification B429/B429M. Note 2: This specification’s use of the term alloy in the general sense includes aluminum as well as aluminum alloy. 1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1M. The equivalent Unified Number System alloy designations are those of Table 4 preceded by A9, for example A91060 for aluminum 1060 in accordance with Practice E527. 1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2. 1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

This specification covers aluminum and aluminum-alloy extruded round tubes either in coils or straight lengths, for general purpose applications such as refrigeration service, gas lines, oil lines, and instrument lines, in the alloys and tempers. Chemical composition: silicon, iron, copper, manganese, magnesium, chromium, zinc, vanadium, titanium, and aluminum. Tubes produced shall be cooled from an elevated temperature shaping process and naturally aged to a substantially stable condition. The specimen shall then undergo tests to check leakage and any evidence of leak shall be a cause for rejection. The ends of tubes in selected tempers shall be capable of being expanded by forcing a steel pin into the tube without signs of cracks, ruptures, or other defects clearly visible by normal vision. The tubes shall be supplied in the mill finish and shall be uniform as defined by the requirements of this specification and shall be commercially sound. Each tube shall be examined to determine conformance to this specification with respect to general quality and identification marking.1.1 This specification covers aluminum and aluminum-alloy extruded round tubes either in coils or straight lengths, for general purpose applications such as refrigeration service, gas lines, oil lines, and instrument lines, in the alloys (Note 2) and tempers shown in Table 2 [Table 3], in outside diameters of 0.250 in. through 0.750 in. [6.00 mm through 20.00 mm]. For diameters over 0.500 in. through 0.750 in. [over 12.50 mm through 20.00 mm], the diameter and wall-thickness tolerances and eddy-current test parameters, if required, shall be agreed upon by the producer and the purchaser. Only tubes in aluminum 1200-H111 and 1235-H111 are sized after extrusion to minimize ovalness.1.2 Alloy and temper designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9 (for example, A91050 for aluminum 1050), in accordance with Practice E527.NOTE 1: For extruded tubes see Specifications B221 or B221M, and for drawn tubes for general-purpose applications see Specification B483/B483M.NOTE 2: Throughout this specification the term alloy in the general sense includes aluminum as well as aluminum alloy.NOTE 3: For inch-pound orders specify B491; for metric orders specify B491M. Do not mix units.1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A2.1.4 The values stated in either inch-pound or SI units are to be regarded separately as standards. The SI units are shown either in brackets or in separate tables. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from two systems will result in nonconformance with the specification.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

This specification covers round, aluminum-clad steel core wire used for mechanical reinforcement in the manufacture of aluminum conductors, aluminum-clad steel reinforced. The base metal shall be steel produced by the openhearth, electric-furnace, or basic-oxygen process and shall be of such composition that the finished clad wire shall have the properties and characteristics prescribed in this specification. The aluminum used for cladding shall have a purity and quantity sufficient to meet thickness and resistance requirements of this specification. The material shall conform to the required tensile properties such as stress, tensile strength, and elongation. The aluminum-clad steel core shall undergo elongation test, tension test, and torsion test. The elongation test shall be determined by an extensometer equipped with a vernier or other instrument reading. In the torsion test, a small tensile load shall be applied to the specimen during testing. The specimen shall be twisted by rotating one of the vises in the same direction until fracture occurs.1.1 This specification covers round, aluminum-clad steel core wire with two designations of tensile strengths, AW2 (Normal Strength) and AW3 (High Strength).1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.2.1 For conductor sizes designated by AWG, the requirements in SI units have been numerically converted from corresponding values stated or derived in inch-pound units. For conductor sizes designated by SI units only, the requirements are stated or derived in SI units.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 590元 加购物车

This specification covers nine thicknesses of annealed aluminum foil for use in manufacture of capacitors and includes UNS alloy designations A91145 and A91235. Foil to be used as anodes in electrolytic capacitors is beyond the scope of this specification. Requirements for quality assurance, chemical analysis, and tensile breaking load test are detailed. The foil shall conform to the chemical composition requirements prescribed for aluminum, silicon and iron, copper, manganese, magnesium, zinc, vanadium, and titanium, and shall meet the specified requirements for tensile breaking load, direct current electrical resistance, and area per unit weight. The foil shall be supplied with the finish bright on one side and matte on the other, in the dry or slick condition (dry annealed A, dry annealed B, dry annealed C, or slick annealed) and shall be tested for surface condition by water or water-alcohol test. Spooling requirements such as roll dimensions, roll winding, and roll covering are given. Foil splices shall be either welded or knurled and shall be free of splits, slivers, wrinkles, ragged edges, or excessive pinholes.1.1 This specification covers nine thicknesses (0.00017 to 0.00050 in. (0.0043 to 0.0127 mm)) of annealed aluminum foil used in the manufacture of capacitors.1.2 Foil to be used as anodes in electrolytic capacitors is beyond the scope of this specification.1.3 Alloy designations are in accordance with ANSI H35.11/H35.1(M). The equivalent Unified Numbering System alloy designations are those of Table 1 preceded by A9, for example, A91145 for Aluminum 1145 in accordance with Practice E527.1.4 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

This specification covers aluminum jacketing for thermal and acoustical insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It provides physical requirements for aluminum jacketing for thermal and acoustical insulation. Classification of aluminum jacketing is based on three factors: outer surface treatment and emittance, alloy and temper per Specification B209, and moisture retarder. The specification covers physical properties, minimum thickness for pipe jacketing, and permissible thickness tolerances. Test methods cover total hemispherical emittance, surface burning characteristics, metal sheet thickness, pinholes in moisture retarder, pencil hardness, and water vapor transmission rate of the moisture retarder.1.1 This specification covers aluminum jacketing for thermal and acoustical insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, or stainless steel nor does it cover the details of thermal or acoustical insulation systems.1.2 This specification provides physical requirements for aluminum jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.1.3 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of aluminum jacketing, see (1).21.4 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.NOTE 1: A version of this specification in SI units is available as Specification C1729M.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 702元 加购物车

定价： 590元 加购物车