4.1 This practice is designed for researchers, applicators, and end users of pesticides where one or more ingredients are being mixed into an aqueous spray system. The practice is useful in determining physical compatibility of aqueous spray mixtures of pesticides and/or fertilizers.4.2 The practice is not designed to determine physical compatibility of non-aqueous based spray mixtures.4.3 The results or the testing should be used to determine the compatibility of the mixture ingredients in dynamic applications. Interpolation of static results to the expectations of the results of this test is not encouraged.1.1 This practice describes the method for the evaluation of the physical compatibility and stability of pesticide tank mixtures diluted for aqueous application. This practice may also be adapted to use with liquid fertilizers in replacement of the water diluent.1.2 Tank mix compatibility can be affected by many variables. Care should be taken to duplicate test conditions. This practice addresses the standard variables such as time, temperature, water hardness, method of agitation, and degree of agitation.1.3 Compatibility is complex and can be affected by other variables such as order of addition, pH of the dilution water, pumping shear, etc. Under the parameters of this practice, the results will define whether the pesticide mixture is or is not compatible in the laboratory. Compatibility or incompatibility should be confirmed under field spray conditions.1.4 Proper safety and hygiene precautions must be taken when working with pesticide formulations to prevent skin or eye contact, vapor inhalation, and environmental contamination.1.5 Read and follow all handling instructions for the specific formulation and conduct the test in accordance with good laboratory practice.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 646元 / 折扣价： 550 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

This guide is intended as a general guide to the correct use of foams. Specific decisions on when or if foam should be used will depend on the circumstances and conditions of each spill situation.Polar solvent resistant AFFF can be applied to some water reactive chemicals with a medium expansion foam nozzle to extinguish a fire and to reduce toxic vapor release to the environment.1.1 This guide restricts itself to addressing the application of foam to water immiscible liquid and some water reactive compounds with boiling points above 15°C for vapor control or fire suppression of land spill or contained spills on water.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For hazard statements, see Section 10.

定价： 0元 / 折扣价： 0 元

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This method evaluates the utility and effectiveness of antibacterial and antifungal agents at use concentrations in controlling the microorganisms responsible for the deterioration of metal-working fluids. The method is applicable to antimicrobial agents that are incorporated into either the metal-working fluid concentrate or into the final-use dilution. 1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This guide details the standard procedures for the preparation of aqueous solutions of soaps and detergents and the determination of their pH. The required reagent for this procedure is distilled water or its equivalent, and the recommended electrodes for the determination of pH are the Fischer Accuphast combination electrode or Orion Ross Sure Flow electrode or their equivalents.1.1 This guide covers the preparation of aqueous solutions of soaps and detergents and the determination of their pH.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 This practice is used commonly by vehicle service or laboratory personnel for sampling and preparing aqueous solutions of engine coolants or antirust for further evaluation and testing.3.2 This practice shall be followed when sampling and preparing aqueous solutions of products for evaluation in ASTM test methods.3.3 Care must be taken to ensure that a representative sample of product is taken.3.4 This practice describes several different test methods. The methods to be followed should be agreed to by the supplier and the customer.1.1 This practice covers information on sampling and preparing solutions of engine coolants and antirusts (Notes 1 and 2).1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: Antirust as referred to in this practice covers products intended for use in automotive/light-duty and heavy-duty applications in which water is used as the cooling medium.NOTE 2: Antirust products are available in liquid and solid form. Solids should be handled as outlined in Annex A1.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 The freezing point of an engine coolant indicates the coolant freeze protection.5.2 The freezing point of an engine coolant may be used to determine the approximate glycol or glycerin content, provided the glycol type is known.1.1 This test method covers the determination of the freezing point of an aqueous engine coolant solution in the laboratory.NOTE 1: Where solutions of specific concentrations are to be tested, they shall be prepared from representative samples as directed in Practice D1176. Secondary phases separating on dilution need not be separated.NOTE 2: These products may also be marketed in a ready-to-use form (prediluted).1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification establishes the requirements for nonaqueous engine coolants used in automobiles or other lightduty service cooling systems. Non-aqueous coolants that conform to the specification will function effectively to provide protection against freezing, boiling, and corrosion without any further dilution. This specification is based upon the knowledge of the performance of non-aqueous engine coolants prepared from new individual or mixtures of virgin industrial grade diols.This specification covers general requirements (color, effect on nonmetals), physical and chemical requirements (relative density, dynamic viscosity, boiling point, thermal conductivity, flash point, ash content, pH, chloride, water, reserve alkalinity, effect on automotive finish [use clear coat thermoset urethane or acrylic urethane finish]), and performance requirements (corrosion in glassware, simulated service test, corrosion of cast aluminum alloys at heat-rejecting surfaces [mg/cm2/week], foaming).1.1 This specification covers the requirements for non-aqueous engine coolants used in automobiles or other light-duty service cooling systems. Non-aqueous coolants that conform to the specification will function effectively to provide protection against freezing, boiling, and corrosion without any further dilution. This specification is based upon the knowledge of the performance of non-aqueous engine coolants prepared from new individual or mixtures of virgin industrial grade diols.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See X1.4 for a specific warning statement.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

定价： 646元 / 折扣价： 550 元 加购物车

4.1 pH is, within the limits described in 1.1, an accurate measurement of the hydrogen ion concentration and thus is widely used for the characterization of aqueous solutions.4.2 pH measurement is one of the main process control variables in the chemical industry and has a prominent place in pollution control.1.1 This test method specifies the apparatus and procedures for the electrometric measurement of pH values of aqueous solutions with the glass electrode. It does not deal with the manner in which the solutions are prepared. pH measurements of good precision can be made in aqueous solutions containing high concentrations of electrolytes or water-soluble organic compounds, or both. It should be understood, however, that pH measurements in such solutions are only a semiquantitative indication of hydrogen ion concentration or activity. The measured pH will yield an accurate result for these quantities only when the composition of the medium matches approximately that of the standard reference solutions. In general, this test method will not give an accurate measure of hydrogen ion activity unless the pH lies between 2 and 12 and the concentration of neither electrolytes nor nonelectrolytes exceeds 0.1 mol/L (M).1.2 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.1.3 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车