4.1 In general, with materials of this type, softening does not take place at a definite temperature. As the temperature rises, these materials gradually and imperceptibly change from brittle solids to soft, viscous liquids. For this reason, the determination of the softening point must be made by a fixed, arbitrary, and closely defined methods if the results are to be comparable.1.1 This test method covers the determination of the softening point of certain alkali-soluble resins having uniform plastic flow characteristics as the melting point is approached.1.2 The resin manufacturer should specify whether or not this test method may be used for his product(s).1.3 This test method is not suitable for styrene-maleic anhydride resins.NOTE 1: For testing rosin and other resins, see Test Method E28. For testing asphalts, tars, and pitches, see Test Method D2398.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 571元 加购物车

4.1 This test method is not appropriate for alkali-soluble resins whose acid functionality is due to incorporated anhydrides. Variations in manufacture, storage, and possible contamination of anhydride functional resins may cause partial hydrolysis, or esterification, which will invalidate data from this test method. Anhydride functional resins should be characterized by Test Method D3644.4.2 This test method is used to measure a property of acid functionalized resins. Acid number determines the utility of resins as well as being a significant quality control measure.1.1 This test method covers the measurement of the free acidity present in certain alkali-soluble resins.1.2 This test method is not suitable for styrene-maleic anhydride resins.1.3 The resin manufacturer should specify whether or not this test method may be used for his product(s).1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 571元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 515元 加购物车

4.1 Vapor pressure is an important specification property of commercial propane, special duty propane, propane/butane mixtures, and commercial butane that assures adequate vaporization, safety, and compatibility with commercial appliances. Relative density, while not a specification criterion, is necessary for determination of filling densities and custody transfer. The motor octane number (MON) is useful in determining the products' suitability as a fuel for internal combustion engines.1.1 This practice covers, by compositional analysis, the approximate determination of the following physical characteristics of commercial propane, special-duty propane, commercial propane/butane mixtures, and commercial butane (covered by Specification D1835): vapor pressure, relative density, and motor octane number (MON).1.1.1 This practice is not applicable to any product exceeding specifications for nonvolatile residues. (See Test Method D2158.)1.1.2 For calculating motor octane number, this practice is applicable only to mixtures containing 20 % or less of propene.1.1.3 For calculated motor octane number, this practice is based on mixtures containing only components shown in Table 1.1.2 The values stated in SI units are to be regarded as standard.1.2.1 Exceptions: 1.2.1.1 Non-SI units in parentheses are given for information only.1.2.1.2 Motor octane number and relative density are given in MON numbers and dimensionless units, respectively.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车