定价： 515元 加购物车

3.1 This classification establishes a series of definite viscosity levels so that lubricant suppliers, lubricant users, and equipment designers will have a uniform and common basis for designating, specifying, or selecting the viscosity of industrial fluid lubricants.3.2 This classification is used to eliminate unjustified intermediate viscosities, thereby reducing the total number of viscosity grades used in the lubrication of industrial equipment.3.3 This system provides a suitable number of viscosity grades, a uniform reference temperature, a uniform viscosity tolerance, and a nomenclature system for identifying the viscosity characteristics of each grade.3.4 This system implies no evaluation of lubricant quality and applies to no property of a fluid other than its viscosity at the reference temperature. It does not apply to those lubricants used primarily with automotive equipment and identified with an SAE number.AbstractThis classification is applicable to all petroleum-base fluid lubricants and to those nonpetroleum materials which may be readily blended to produce fluid lubricants of a desired viscosity, that is, lubricants for bearings, gears, compressor cylinders, hydraulic fluids, etc. This classification is used to eliminate unjustified intermediate viscosities, thereby reducing the total number of viscosity grades used in the lubrication of industrial equipment. The lubricants shall be classified according to viscosity grades: ISO VG 2; ISO VG 3; ISO VG 5; ISO VG 7; ISO VG 10; ISO VG 15; ISO VG 22; ISO VG 32; ISO VG 46; ISO VG 68; ISO VG 100; ISO VG 150; ISO VG 220; ISO VG 320; ISO VG 460; ISO VG 680; ISO VG 1000; ISO VG 1500; ISO VG 2200; and ISO VG 3200.1.1 This classification is applicable to all petroleum-base fluid lubricants and to those nonpetroleum materials which may be readily blended to produce fluid lubricants of a desired viscosity, that is, lubricants for bearings, gears, compressor cylinders, hydraulic fluids, etc.1.2 This classification is applicable to fluids ranging in kinematic viscosity from 2 cSt to 3200 cSt (mm2/s) as measured at a reference temperature of 40 °C. In the category of petroleum-base fluids, this covers the range from kerosene to heavy cylinder oils.1.3 Fluids of either lesser or greater viscosity than the range described in 1.2 are, at present, seldom used as industrial lubricants. Should industrial practices change, then this system, based on a mathematical series of numbers, may be extended to retain its orderly progression.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

5.1 The data obtained for the reference test fluid are intended to be used by laboratory personnel to determine their capability to perform tests properly. If a particular determination does not fall within the prescribed limits, it has to be assumed that an error occurred in the application of the test procedure.5.2 The coolant composition given in this specification is not intended to be a commercial product.AbstractThis specification covers a reference ethylene glycol-base test fluid to be used in providing base line data for ASTM coolant test procedures. The reference test fluid concentrate shall be prepared to conform to the requirements as to chemical composition prescribed. The materials used to prepare the reference test fluid shall meet the requirements specified. The formulated reference test fluid concentrate shall conform to the requirements for laboratory test performance prescribed.1.1 This specification covers a reference ethylene glycol-base test fluid to be used in providing base line data for ASTM coolant test procedures.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 646元 加购物车

定价： 571元 加购物车

定价： 646元 加购物车

定价： 515元 加购物车

定价： 571元 加购物车

定价： 571元 加购物车

5.1 This test method covers the gravimetric measurement4 of metal removal fluid aerosol concentrations in workplace atmospheres.5.2 This test method provides total particulate matter concentrations for comparison with historical exposure databases collected with the same technology.5.3 This test method provides an extension to current non-standardized methods by adding an extractable mass concentration which reduces interferences from nonmetal removal fluid aerosols.5.4 This test method does not address differences between metal removal fluid types, but it does include extraction with a broad spectrum of solvent polarity to adequately remove many of the current fluid formulations from insoluble background aerosol.55.5 This test method does not identify or quantify any specific putative toxins in the workplace that can be related to metal removal fluid aerosols or vapors.5.6 This test method does not address the loss of semivolatile compounds from the filter during or after collection.1.1 This test method covers a procedure for the determination of both total collected particulate matter and extractable mass metalworking fluid aerosol concentrations in the range of 0.07 to 5 mg/m3 in workplace atmospheres.1.2 This test method describes a standardized means of collecting worker exposure information that can be compared to existing exposure databases, using a test method that is also more specific to metal removal fluids.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

定价： 712元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车