This standard specifies requirements for measuring receivers [i.e., electromagnetic interference (EMI) receivers and spectrum analyzers with and without preselection] used for radiated and conducted emission measurements. Specifications relate to the measuring equipment only, not transducers like antennas, line impedance stabilization networks (LISNs), or current probes.

定价： 59元 / 折扣价： 51 元

This standard covers the conformance test procedures for alternating-current high-voltage motor-starter fuses covered in the applicable American National Standards listed in 2.1. High-voltage motor-starter fuses are backup, current limiting fuses used in conjunction with high-voltage Class E2 motor starters. This standard does not cover installations under the exclusive control of electric utilities for the purposes of communication or metering, or for the generation, control, transformation,… read more transmission, and distribution of electric energy located in buildings used exclusively by utilities for such purposes, or located outdoors on property owned or leased by the utility or on public highways, streets, roads, and the like, or located outdoors by established rights on private property. read less

定价： 56元 / 折扣价： 48 元

This guide shows the basis for the acceptability criterion of k4 dB for the site attenuation measurements required in ANSI C63.4-1988.

定价： 88元 / 折扣价： 75 元

This standard applies to security screening systems that utilize x-ray or gamma radiation and are used to inspect people who are not inside vehicles, containers, or enclosures. Specifically, this standard applies to systems used to detect objects carried on or within the body of the individual being exposed. The following types of systems are included in the scope of this standard: ⎯ Systems designated as fixed, portal, re-locatable, transportable, mobile, or gantry. ⎯ Systems employing… read more detection of primary radiation (transmission systems), or scatter radiation (backscatter systems), or a combination of both. ⎯ Systems that are primarily imaging but that also may have complementary features such as material discrimination, or automatic active or passive threat alerts. This standard will not address how to test these complementary features. read less

定价： 124元 / 折扣价： 106 元

This document establishes standard test methods and test objects for measuring the imaging performance of x-ray computed tomography (CT) security-screening systems. The quality of data for automated analysis is the primary concern. This document does not address the system's ability to use this image data to automatically detect explosives or other threat materials, nor is it intended for vendor-to-vendor comparisons of threat-detection performance. This standard does not purport to address… read more radiation safety and health practices associated with CT security-screening systems; users are advised to determine the applicability of regulatory limitations prior to use. Four annexes are included. Annex A is a bibliography (informative). Annex B (normative) provides mechanical drawings of the imaging test objects that compose the test article. A sample test report form is given in Annex C (informative). Finally, Annex D (informative) offers statistical guidance on multiple scans, summary statistics, and comparison of results. read less

定价： 95元 / 折扣价： 81 元

定价： 126元 / 折扣价： 108 元

This standard is intended to be used to determine the imaging performance of x-ray and gamma-ray systems utilized to inspect loaded or empty vehicles, including personal and commercial vehicles of any type; marine and air cargo containers of any size; railroad cars; and palletized or Unpalletized cargo larger than 1 m × 1 m in cross-section. The standard applies to systems that are the following: -- Single or multiple energy, source, or view -- Employ primary (i.e., transmission) and/or scatter… read more (e.g., backscatter) radiation detection -- Used to detect prohibited and controlled materials and/or to verify manifests -- Primarily imaging systems but also may have complementary features such as material discrimination and automatic active or passive threat alerts. This standard does not address how to test these complementary features. Adherence to all applicable mechanical and electrical safety requirements and compatibility with all applicable installation codes, including electro-magnetic compatibility requirements, is extremely important for any type of x-ray or gamma-ray screening system; however, identification of these requirements is not within the scope of this standard. read less

定价： 110元 / 折扣价： 94 元

This standard establishes the minimum performance criteria for portable radiation protection instrumentation for use in ionizing radiation fields under both normal and extreme environmental conditions, i.e., all environmental conditions. For the portable radiation detection instrumentation addressed in this standard, the radiological ranges for the performance tests are as follows: the dose rate range of operation taken as background to 10 Gy/h (1000 rad/h); the activity-per-unit-area range for… read more surface contamination monitors taken as 0.01 Bq/cm (60 dpm/100 cm) or 0.05 Bq/cm (300 dpm/100 cm) to 200 Bq/cm (1.2 × 10 dpm/100 cm). The testing methods verify that the performance criteria are met over the range of operating conditions for each type of instrumentation. This standard does not specify which instruments or systems are required, nor does it consider the number of specific applications of such instruments. read less

定价： 80元 / 折扣价： 68 元

This standard covers threaded zinc coated ferrous strand-eye anchor rods and nuts commonly used in overhead line construction.

定价： 53元 / 折扣价： 46 元

定价： 81元 / 折扣价： 69 元

This application guide for capacitance current switching applies to ac high-voltage circuit breakers rated in accordance with American National Standard Requirements for Capacitance Current Switching for A C High-Voltage Circuit Breakers, C37.073-1972. It is intended to supplement the American National Standard Application Guide for AC High-Voltage Circuit Breakers, C37.010-1972 (IEEE Std 320-1972), and specifically, to enlarge on Section 4.14.3, Capacitor Switching, and Section 4.14.4, Line… read more Charging Switching. Circuit breakers rated and manufactured to meet other standards should be applied in accordance with application procedures adapted to their specific ratings. read less

定价： 65元 / 折扣价： 56 元

This standard provides recommended test methods and limits for assuring the radio frequency (RF) immunity of office equipment to general use transmitters with transmitter power up to 8 watts.

定价： 141元 / 折扣价： 120 元

This standard is applicable to three-pole circuit breakers used in three-phase systems and single-pole circuit breakers used in single-phase systems, both indoor and outdoor AC high-voltage types, rated above 1000 volts on a symmetrical current basis. This standard does not cover circuit breakers used at rated frequencies other than 50 Hz or 60 Hz, or generator circuit breakers that are covered in IEEE Std. C37.013.

定价： 85元 / 折扣价： 73 元

定价： 66元 / 折扣价： 57 元

This standard provides preferred ratings for indoor AC medium-voltage switches used in metal-enclosed switchgear.

定价： 75元 / 折扣价： 64 元