This test method covers the determination of the relative effectiveness of wood preservatives in round posts set in the ground in field plots. Two tests shall be used, one for small sapwood posts which is the preferred test if major interest lies in testing the preservative when fairly evenly distributed throughout the piece, and the second for large posts which is preferred when the preservative is tested under conditions of gradient retention and distribution normally encountered in commercial operations. The requirements for preparation of the material for testing and the test procedures shall be as follows: test plot; test specimens; treatment procedure; after-treatment handling of posts; installation of posts; inspection of specimens; evaluation of results; and reports.1.1 This test method covers the determination of the relative effectiveness of wood preservatives in round posts set in the ground in field plots. Two tests are described, one for small (3 to 5 in. (80 to 130 mm) in diameter) sapwood posts which is the preferred test if major interest lies in testing the preservative when fairly evenly distributed throughout the piece, and the second for large posts (7 to 10 in. (180 to 250 mm) in diameter) which is preferred when the preservative is tested under conditions of gradient retention and distribution normally encountered in commercial operations.1.2 The requirements for preparation of the material for testing and the test procedures appear as follows:1.3 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents of inch-pound units may be approximate.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元

The forest products finishing industry has encountered difficulties in measuring the temperature of painted surfaces prior to, during, and after the curing process. The use of thermocouples is not entirely satisfactory because the thermocouple wires tend to conduct heat away too rapidly from the area where the temperature is being measured. Infrared radiation thermometers that are simple to operate can circumvent this difficulty. After calibration they are aimed at the surface, switched on, and the temperature read directly from an indicating gage. Note 1—Temperature-sensitive crayons, papers, and pellets may be successfully used to measure only the highest temperature reached by painted surfaces during the curing cycle. There are several different types of infrared radiation thermometers, including those based on lead sulfide or thermistor sensors and those that are simple thermal voltaic transducers. As such they respond to different wavelengths of infrared radiation and have different areas of applicability. Only instruments that have been evaluated are included in this practice.1.1 This practice is intended to serve as a guide in measuring with infrared instruments the temperature during the curing process of coatings applied to wood products. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元

This test method is useful in determining the relative efficacy between various treatments and naturally occurring wood-destroying agents. It is an initial means of estimating the tolerance limits of the biologically destructive agents or the threshold values of the chemical preservative, or both.This test method is not intended to provide quantifiable reproducible values. It is a qualitative method designed to provide a reproducible means of establishing relative efficacy between experimental contract levels.1.1 This test method covers the relative effectiveness of wood preservatives in small wood specimens exposed to a natural marine environment. It is not within the scope of this test method to determine the retention or duration of protection for commercial size piles and timbers.1.2 The requirements for preparing the material for testing and the test procedures appear in the following order: SectionSummary of Test Method Test Specimens Pretreatment Handling Treatment Procedure Post-Treatment Handling Assembly of Test Specimens Exposure Inspection Evaluation of Results Reports 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元

1.1 This test method covers determination of the resistance to checking and cracking of clear nitrocellulose lacquer films applied to wood or plywood substrates when subjected to sudden changes from high to low temperatures.1.2 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.>

定价： 0元

1.1 These procedures cover the chemical analysis by the lime ignition method of treating solutions containing pentachlorophenol and of wood treated with pentachlorophenol. The method is suitable for the determination of up to 0.05 g of pentachlorophenol in treating solutions (Section ), up to 0.05 g of pentachlorophenol in wood volumes up to 0.25 in.3 (Section 11), and up to 0.25 g of pentachlorophenol in wood volumes up to 2.0 in.3 (Section ).1.2 This test method is not applicable to samples containing halogens other than chlorine unless appropriate correction can be made. Total halogen (excluding fluorine) is calculated as its pentachlorophenol equivalent of chloride.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元

3.1 This test method is useful in determining the relative anti-swelling efficiency of various water-repellent formulations when applied to wood. It is the initial means of estimating the ability of water-repellent treated wood to perform satisfactorily when exposed to liquid water environments.3.2 The swelling differences of untreated wood species when subjected to water immersion can also be determined by this test method.3.3 This method is a basic screening test and thus provides an initial determination of the anti-swelling efficiency of water repellents. It is a qualitative method designed to provide a reproducible means of establishing: (1) the anti-swelling efficiency of water-repellent formulations, and (2) the relative swelling of untreated wood species when both are exposed to liquid water environments.1.1 This test method is designed to evaluate the effectiveness of water-repellent compositions for retarding dimensional changes in coated wood submerged in water. It can also be used to measure the differential swelling of untreated wood when exposed to liquid water environments. The compositions tested are designed to be mixed until uniform and applied by brush, roller, dip or spray to an exterior wood surface.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元

定价： 453元

定价： 637元

定价： 384元

定价： 384元

定价： 665元

定价： 723元

定价： 453元

定价： 379元

定价： 810元