定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

5.1 This guide sets forth minimum standard requirements for use in local codes and ordinances relating to commercial and public water spray/play areas.5.2 This guide does not have the effect of law, nor is it intended to supersede local codes and ordinances of a more restrictive nature.5.3 This guide provides certain recommendations to assist those who intend to provide protection against injuries or fatalities associated with any possible vehicle passage into, or pedestrian passage to or from a water spray/play area environment by children. This would include, but not be limited to, state and local governments, model code organizations, building code groups, and consumers. It is understood that the format will vary depending upon the specific use and local conditions.1.1 This guide provides the recommended minimum requirements for various types of fences for commercial and public outdoor water spray/play areas.1.2 This guide provides for the safety of occupants in water spray/play areas or zones as it pertains to vehicular intrusion as well as other participant intrusion, and for children containment or entry/exit.1.3 This guide does not choose the product components for the fence system, the choice of which should be made by the operators of the water spray/play area space and their specification writers or drafters based upon their determination of the merits of the products that could be used.1.4 The values stated in inch-pound units are to be regarded as the standard. The SI values stated in parentheses are provided for information purposes only.1.5 This guide does not purport to address the aspect of safety within a water spray/play area or zone. It is the responsibility of the user of this guide to establish appropriate safety practices as related to the water spray/play area and determine the applicability of regulatory requirements prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 515元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 618元 加购物车

This practice describes methods that may be used to repair damaged hot-dip galvanized coatings on hardware, structural shapes, and other products fabricated prior to hot-dip galvanizing, and uncoated areas remaining after initial hot-dip galvanizing. The damage may be the result of welding or cutting (flame), in which case the coating will be damaged predominantly by burning. This practice can also be used to repair hot-dip galvanized coatings damaged by excessively rough handling during shipping or erection. Requirements concerning the renovation of uncoated areas remaining after initial hot-dip galvanizing are contained within the applicable material specification. This practice describes the use of three types of material that possess the required properties for repair of damaged galvanized coatings, namely: (1) zinc-based solders which includes low melting point zinc alloy repair rods or powders, (2) paints containing zinc dust, and (3) sprayed zinc (metallizing). The material used for repair shall have the specified coating thickness, shall provide barrier protection and preferably be anodic to steel, and application of the coating shall be possible under shop or field conditions.1.1 This practice describes methods that may be used to repair damaged hot-dip galvanized coatings on hardware, structural shapes, and other products fabricated prior to hot-dip galvanizing, and uncoated areas remaining after initial hot-dip galvanizing. The damage may be the result of welding or cutting (flame), in which case the coating will be damaged predominantly by burning. This practice can also be used to repair hot-dip galvanized coatings damaged by excessively rough handling during shipping or erection. Requirements concerning the renovation of uncoated areas remaining after initial hot-dip galvanizing are contained within the applicable material specification.1.2 This practice describes the use of low melting point zinc alloy repair rods or powders made specifically for this purpose, the use of paints containing zinc dust, and the use of sprayed zinc (metallizing).1.3 The extent of repair shall be limited to an area mutually agreeable to the contracting parties. Similarly, contracting parties shall agree to the repair method to be used.1.4 Units—This specification is applicable to orders in either inch-pound units (as A780) or in SI units (as A780M). Inch-pound units and SI units are not necessarily exact equivalents. Within the text of this specification and where appropriate, SI units are shown in brackets. Each system shall be used independently of the other without combining values in any way.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 618元 加购物车

定价： 571元 加购物车

1.1 This consumer safety specification covers scald-preventing devices and systems delivering water in bathing areas.1.2 This specification establishes the minimum performance requirements for the devices and systems to minimize the risks associated with the hazards of scalds.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车