4.1 Since coated pipe may be stored outdoors for long periods before burial, weathering tests described in this practice are needed to evaluate the stability of these coatings stored outdoors. The results obtained should be treated only as indicating the general effect of weathering. Exposure conditions vary greatly from year to year, from one part of a year to another, and from locality to locality. The results of short-term exposure tests in the north are more meaningful if exposure is started in the summer followed by a winter season. In southern areas where climatic conditions are more uniform throughout the year, the time of year when short-term exposure is started is less critical. In all localities, the longer the exposure period, the more reliable are the results obtained.1.1 This practice is intended to define conditions for the exposure of coated metal pipe to weather.1.2 This practice specifies qualifications for the samples, procedure to be followed in exposure to weather, and procedure for evaluating effects of exposure including visual examination and other tests.1.3 The values stated in SI units to three significant decimals are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

4.1 The deterioration of an insulating coating film is intimately related to its moisture content. The water penetration test provides a means for monitoring the passage of moisture through a coating material by means of changes in its dielectric constant. When expressed in relation to time, the test data will reflect a rate of deterioration which is a characteristic of the coating material and will bear a relation to its expected useful life as an insulating coating. The test for water penetration will also provide information that is useful in establishing the optimum coating thickness for a given material.1.1 This method covers the determination of the apparent rate of depth of water penetration into insulating coatings applied to pipe.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 515元 加购物车

定价： 590元 加购物车

定价： 515元 加购物车

定价： 590元 加购物车

定价： 590元 加购物车

定价： 515元 加购物车

定价： 515元 加购物车

定价： 646元 加购物车

4.1 Indentation hardness measurements have proven to be useful in rating coatings on rigid substrates for their resistance to mechanical abuse, such as that produced by blows, gouging, and scratching. These measurements do not necessarily characterize the resistance to mechanical abuse of coatings that are required to remain intact when deformed.1.1 These test methods cover the determination of the indentation hardness of organic materials such as dried paint, varnish, and lacquer coatings, when applied to an acceptable plane rigid surface, for example, metal or glass.1.2 Two methods are covered as follows:  SectionsMethod A—Knoop Indentation Hardness 6 – 12Method B—Pfund Indentation Hardness 13 – 191.3 Method A, which has the greater precision, provides hardness values in terms of Knoop Hardness Number (KHN). Method B provides hardness in terms of Pfund Hardness Number (PHN). Although the hardness value scales of these methods differ, the methods agree in the ranking of coating hardness.1.4 Test Method A of these test methods is similar in content (but not technically equivalent) to ISO 6441-1 and ISO 6441-2.1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.6 This standard does not purport to address the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

5.1 Tensile properties determined by this method are of value in studying the behavior of coatings subjected to environmental stresses, such as those produced by aging and weathering. (See Refs. (1-10).)45.2 Tensile properties may vary with specimen thickness, method of preparation, gage length, rate of load application, tensile tester response, and type of grips used. Consequently, where precise comparative results are desired, these factors must be carefully controlled.1.1 This test method covers the determination of the elongation, tensile strength, and stiffness (modulus of elasticity) of organic coatings when tested as free films.1.2 The values stated in SI units are to be regarded as standard. The values given in parentheses are mathematical conversions to inch-pound units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification covers the requirements for autoclavable protective coatings on laboratory glassware. These coatings will not prevent the escape of liquids from vessels under pressure. Materials shall be tested and shall conform to requirements for physical and chemical resistance, autoclavability, temperature, microwaving, thermal combustion, flammability, and color.1.1 This specification covers the requirements for autoclavable protective coatings on laboratory glassware up to and including the 4L size. These coatings will not prevent the escape of liquids from vessels under pressure.1.2 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车