定价： 515元 / 折扣价： 438 元 加购物车

定价： 590元 / 折扣价： 502 元 加购物车

This practice contains two recommendations based on several reported practices for the process selection in electroplating on tungsten and tungsten alloys. Surfaces should be cleaned either by descaling, solvent cleaning, or alkaline soak cleaning before electroplating. Evaluating which of the suggested processes to use is dependent on the application of the produced coating.1.1 This practice makes recommendations of several reported practices for electroplating on tungsten and its alloys along with comments as a guide in the selection of a processing method for a given application. Because data on methods and results of evaluation with electroplated coatings on tungsten are limited, a recommendation of one method over another cannot be made.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This guide covers rolled nickel-chromium-molybdenum-tungsten alloys plate, sheet, and strip. The material shall be composed of carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, tungsten, molybdenum, iron, aluminum, titanium, nickel, and copper. The material shall be uniform in quality and temper, smooth, commercially straight or flat, and free of injurious imperfections. Tension test specimens shall be taken from material in the final condition and tested transverse to the direction of rolling when width will permit. Inspection of the material shall be made as agreed upon between the manufacturer and the purchaser as part of the purchase contract.1.1 This specification covers rolled nickel-chromium-molybdenum-tungsten alloys (UNS N06110)2 plate, sheet, and strip.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696) and nickel-chromium-cobaltmolybdenum alloy (UNS N06617) in the form of hot-finished and cold-worked rounds, squares, hexagons, rectangles, and cold-worked wire. The material shall conform to the composition limits specified in a reference material. The material shall be uniform in quality and condition, smooth, commercially straight or flat, and free of injurious imperfections. Mechanical properties of the alloys like tensile strength, yield strength, elongation, and hardness shall be determined by tension and hardness tests.1.1 This specification2 covers nickel-chromium-aluminum alloy, nickel-chromium-iron alloys,3 nickel-chromium-cobalt-molybdenum alloy, nickel-iron-chromium-tungsten alloy, and nickel-chromim-molybdenum-copper alloy in the form of hot-finished and cold-worked rounds, squares, hexagons, rectangles, and cold-worked wire.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following precautionary caveat pertains only to the test methods portion, Section 12, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers UNS N06110 nickel-chromium-molybdenum-tungsten alloy hot-worked rods and bars and cold-worked rods. The chemical compositions and mechanical properties of the materials should conform to the requirements in this specification.1.1 This specification covers nickel-chromium-molybdenum-tungsten (UNS N06110)2 in the form of hot-worked rod and bar and cold-worked rod in the conditions shown in Table 1.(A) Forging quality is furnished to chemical requirements and surface inspection only. No tensile properties are required.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696) and nickel-chromium-cobalt molybdenum alloy (UNS N06617) in cold-worked annealed, hot-worked annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications. The material shall conform to the required chemical composition for nickel, chromium, iron, manganese, molybdenum, cobalt, aluminum, carbon, copper, boron, silicon, sulfur, titanium, niobium, phosphorous, zirconium, yttrium, and cerium. The following test methods shall be performed on the alloys, namely: chemical analysis, tension test, and hydrostatic or nondestructive electric test. The material shall conform to the required mechanical properties such as tensile strength, yield strength, elongation, nondestructive electric test, and rounding method.1.1 This specification2 covers nickel-chromium-aluminum alloys (UNS N06699), nickel-chromium-iron alloys (UNS N06600, N06601, N06603, N06690, N06693, N06025, N06045, and N06696),3 nickel-chromium-cobalt-molybdenum alloy (UNS N06617), nickel-iron-chromium-tungsten alloy (UNS N06674), and nickel-chromium-molybdenum-copper alloy (UNS N06235) in cold-worked annealed, hot-worked annealed, and hot-finished seamless pipe and tube intended for general corrosion resistant and heat resistant applications.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following safety hazards caveat pertains only to the test methods portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers annealed UNS N06110 alloy welded pipes for general corrosion applications. Each pipe should be made from the flat-rolled alloy by an automatic welding process without any filler metal additions. Either only the weld metal or both weld and base metals should be cold worked after welding and prior to final annealing. The piped should also be furnished and the oxide removed. Descaling is not necessary when bright annealing is used.1.1 This specification covers welded UNS N061102 pipe in the annealed condition (temper) for general corrosion applications.1.2 This specification covers pipe sizes in schedules shown in Table 1.(A) Schedules 5S and 10S wall thicknesses do not permit threading in accordance with the American National Standard for Pipe Threads (ANSI B2.1).1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 The following precautionary caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers welded nickel-chromium-molybdenum-tungsten alloy (UNS N06110) tube in the annealed condition (temper) for general corrosion applications. The tube shall be made from flat-rolled alloy by an automatic welding process with no addition of filler material. Subsequent to welding and prior to final annealing, the material shall be cold-worked in either the weld metal only or both weld and base metal. The tube shall be furnished with oxide removed. When bright annealing is used, descaling is not necessary. Flattening, flange, and nondestructive tests shall be performed on the tube.1.1 This specification covers welded UNS N061102 tube in the annealed condition (temper) for general corrosion applications.1.2 This specification covers outside diameter and nominal wall tube.1.2.1 The tube sizes covered by this specification are 1/8 to 5 in. (3.2 to 127 mm) in outside diameter and 0.015 to 0.148 in. (0.4 to 3.8 mm), inclusive, in wall thickness.1.3 The values stated in inch-pound units are to be regarded as the standard. The SI units in parentheses are provided for information only.1.4 The following precautionary caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers the standard for cold-worked seamless pipe and tube made from nickel-chromiummolybdenum-tungsten alloys (UNS N06110). Tensile properties such as yield strength, tensile strength, and elongation shall be assessed by appropriate test methods. Each pipe and tube shall be subjected to a hydrostatic test, pneumatic test, and nondestructive electric test. In case of a leak, the leaking area may be cut out. The specimen may then be retested as specified.1.1 This specification2 cover nickel-chromium-molybdenum-tungsten alloys (UNS N06110)3 in the form of cold-worked seamless pipe and tube in the conditions shown in Table 1.1.2 Hot-worked material is available. Properties and permissible tolerances are to be agreed upon between the manufacturer and purchaser.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4  The following precautionary caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provide by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers wrought unalloyed tungsten plate, sheet, and foil. The various tungsten flat products covered by this specification shall be formed with the conventional rolling, forging, or extrusion equipment, normally found in primary ferrous and nonferrous plants. The ingot metal shall be consolidated employing either the powder metallurgy or vacuum-arc-casting process. The materials shall conform to the required chemical composition for carbon, oxygen, nitrogen, iron, nickel, and silicon. Plate, sheet, and foil shall be furnished in the following metallurgical condition: hot-rolled, stress relieved, and cold-rolled. The materials shall also conform to the required permissible variations in physical dimensions such as thickness, width, length, and flatness.1.1 This specification covers wrought unalloyed tungsten plate, sheet, and foil.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 The following precautionary caveat pertains only to the test method portions of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 515元 / 折扣价： 438 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车