定价： 345元 / 折扣价： 294 元 加购物车

定价： 590元 加购物车

4.1 The requirements of this guide apply to personnel who perform coating and lining work inspection during (1) fabrication, (2) receipt of items at the construction site, (3) construction, (4) pre-operational and startup testing, and (5) operational phases of nuclear facilities.4.2 It is the responsibility of each organization participating in the project to ensure that only those personnel within their respective organizations who meet the requirements of this guide are permitted to perform coating and lining work inspection activities covered by this guide.4.3 The organization(s) responsible for establishing the applicable requirements for activities covered by this guide shall be identified, and the scope of their responsibility shall be documented. Delegation of this responsibility to other qualified organizations is permitted and shall be documented.4.4 It is the responsibility of the organization performing these activities to specify the detailed methods and procedures for meeting the requirements of this guide, unless those methods and procedures are otherwise specified in the contract documents.4.5 In the event of conflict, users of this guide must recognize that the licensee’s plant-specific quality assurance program and licensing commitments shall prevail with respect to the process of qualifying personnel performing inspection of coating and lining work.1.1 This guide delineates the requirements for development of procedures for the qualification and certification of personnel who perform inspection of coating and lining work. Establishment of qualification requirements to verify conformance to specified requirements for nuclear facility coating and lining work is necessary to assure satisfactory performance of the inspections and to avoid compromising safety-related coating systems.1.2 The intent of this guide is to provide a uniform interpretation of the requirements in ANSI/ASME N45.2.6 or ANSI/ASME NQA-1 as applicable, for the inspection of coating and lining work in nuclear facilities.1.3 It is the intent of this guide to provide a recommended basis for qualification and certification, not to mandate a singular basis for all qualifications. Variations or simplifications of the qualifications described in this guide may be appropriate for special coating and lining work other than safety-related coating and lining systems. Similarly, the qualification and certification process might be abbreviated for work of minor scope such as touch-up.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

This practice covers the testing of the integrity of high-efficiency particulate air (HEPA) filters installed in laminar flow clean rooms of the ceiling to floor or wall to wall type, and laminar flow clean work stations using condensation nuclei detector. The recommended practice may be used to detect faults or voids in the filter media itself or in the joints between the filter and the room or work station structure. The preparation for testing and the procedure for the proper testing are presented in details.1.1 This practice covers the testing of the integrity of high-efficiency particulate air (HEPA) filters installed in laminar flow clean rooms of the ceiling to floor or wall to wall type, and laminar flow clean work stations. The recommended practice may be used to detect faults or voids in the filter media itself or in the joints between the filter and the room or work station structure. The determination of filter media efficiency is not within the scope of this practice.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.2.1 Exception—The values given in parentheses in inch-pound units are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 571元 加购物车

定价： 541元 / 折扣价： 482 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 260元 / 折扣价： 221 元 加购物车

定价： 553元 / 折扣价： 471 元 加购物车

定价： 1177元 / 折扣价： 1001 元 加购物车

定价： 0元 加购物车

定价： 1200元

定价： 996元

Update No. 1 was published as notification that this is now a National Standard of Canada This PDF includes Update No. 1 1 Scope 1.1 General This Standard applies to portable, integral chassis elevating work platforms with bases that cannot be

定价： 546元 / 折扣价： 465 元

定价： 865元 / 折扣价： 736 元