定价： 646元 加购物车

定价： 843元 加购物车

定价： 712元 加购物车

定价： 927元 加购物车

定价： 927元 加购物车

定价： 646元 加购物车

4.1 This practice is intended to help reduce risks associated with lead hazards in buildings by providing standardized requirements for preserving records, findings, and recommendations associated with lead hazard activities.4.2 This practice is intended for use by individuals and organizations that develop and have need to preserve objective evidence when contracting for or when conducting lead hazard activities themselves.4.2.1 This practice is intended to assist in complying with management system requirements for record keeping promulgated by authorities having jurisdiction regarding conduct of lead hazard activities.1.1 This practice describes requirements for preservation of records generated during lead hazard activities.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 571元 加购物车

定价： 927元 加购物车

5.1 This practice provides nine figures of merit which may be used to estimate the relative thermal hazard of thermally unstable materials. Since numerous assumptions must be made in order to obtain these figures of merit, care must be exercised to avoid too rigorous interpretation (or even misapplication) of the results.5.2 This practice may be used for comparative purposes, specification acceptance, and research. It should not be used to predict actual performance.1.1 This practice covers the calculation of hazard potential figures of merit for exothermic reactions, including:(1) Time-to-thermal-runaway,(2) Time-to-maximum-rate,(3) Critical half thickness,(4) Critical temperature,(5) Adiabatic decomposition temperature rise,(6) Explosion potential,(7) Shock sensitivity,(8) Instantaneous power density, and(9) National Fire Protection Association (NFPA) instability rating.1.2 The kinetic parameters needed in this calculation may be obtained from differential scanning calorimetry (DSC) curves by methods described in other documents.1.3 This technique is the best applicable to simple, single reactions whose behavior can be described by the Arrhenius equation and the general rate law. For reactions which do not meet these conditions, this technique may, with caution, serve as an approximation.1.4 The calculations and results of this practice might be used to estimate the relative degree of hazard for experimental and research quantities of thermally unstable materials for which little experience and few data are available. Comparable calculations and results performed with data developed for well characterized materials in identical equipment, environment, and geometry are key to the ability to estimate relative hazard.1.5 The figures of merit calculated as described in this practice are intended to be used only as a guide for the estimation of the relative thermal hazard potential of a system (materials, container, and surroundings). They are not intended to predict actual thermokinetic performance. The calculated errors for these parameters are an intimate part of this practice and must be provided to stress this. It is strongly recommended that those using the data provided by this practice seek the consultation of qualified personnel for proper interpretation.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 646元 加购物车

定价： 646元 加购物车

定价： 712元 加购物车

定价： 927元 加购物车

定价： 646元 加购物车