定价： 0元 / 折扣价： 0 元 加购物车

4.1 Dimensions are important properties in the general construction of a box, and accurate methods of measurement are required for research work, routine control, and acceptance testing for conformance to specifications. For packages to carry and protect their contents effectively and efficiently, boxes and interior components must be properly and consistently sized. Correctly dimensioned and well-made boxes can be more easily set up by hand or be erected using automatic equipment. “Square” boxes (rectangular parallelepipeds) will stack better to accept load and improve stability during storage and shipment.4.1.1 Interior dimensions of boxes are critical when the contents of the box are intended to fill or nearly fill the box with little unused side and head space. The inside dimension by tape method are the size values most often cited in box design (see 9.1, and TAPPI T827). The interior size of a box can be estimated from the score to score measurements when the scoring allowance is taken into account (see Appendix X2). The actual inside dimensions can be measured directly using the box gauge method (see 9.2). Either method can be used to measure interior box dimensions.4.1.2 Exterior dimensions may be the critical design criteria when attempting to optimize use of the shipping platform area and overall stack height based on transportation and storage limitations. Exterior dimensions are also key design elements when making common footprint boxes.5 The exterior dimensions of a box can be measured directly using the exterior dimensions by tape method (see Appendix X1).4.2 Measuring a Lot Quantity of Boxes—This method determines if a lot (that is, production run) is within specified tolerance for each dimension (length, width, and depth as are shown in Practice D5118/D5118M). A minimum of five specimens are measured. The test result for each dimension is the individual measurements of that dimension on all specimens (see 9.3).4.3 Measuring Single Boxes—Determines if one particular box is within specified tolerance for each dimension. The test result for each dimension is the average of all measurements of that dimension (see 9.4).1.1 This test method covers the determination of the interior and exterior dimensions of regular slotted or special slotted styles of single-wall corrugated, double-wall corrugated and solid fiberboard boxes.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

1.1 This standard is a compilation of terminology related to the body dimensions for apparel sizing. 1.2 For definitions of other textile terms, refer to Terminology D123. 1.3 The terms are listed in alphabetical order regardless of whether they are horizontal or vertical measurements. The three dimensional Avatars were created by Alvanon Inc. See Figs. 1-19. 1.4 The term “height” has been designated for vertical measurements. 1.5 The term “length” has been designated for contour measurements.

定价： 646元 加购物车

定价： 515元 加购物车

定价： 590元 加购物车

5.1 These test methods shall be used where precise dimensions are necessary for the calculation of properties expressed in physical units. They are not intended to replace practical thickness measurements based on commercial portable tools, nor is it implied that thickness measurements made by the procedures will agree exactly.5.2 Examples of machinist’s micrometers, including pictures with descriptions of their components and pictures of the micrometers used can be located in Practice A1073/A1073M. However, make sure the micrometer, the calibration of it, and the use of it adheres to the requirements of this standard.1.1 These test methods cover determination of the physical dimensions of solid plastic specimens where the dimensions are used directly in determining the results of tests for various properties. Use these test methods except as otherwise required in material specifications.1.2 The values stated in SI units are to be regarded as standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This standard and ISO 16012 address the same subject matter, but differ in technical content.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 590元 加购物车

3.1 The dimensions listed in this practice represent the dimensions of rectangular and tapered refractory shapes manufactured and used in the United States.3.2 The modular concept of dimensions permits a versatile arrangement of bonding during the construction of masonry units.1.1 This practice covers the dimensions for rectangular and tapered brick in common usage in the United States.1.2 The dimensions are modular based on 38 mm as the basic module as described in Practice C861.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

5.1 This test method provides for determining the physical dimensions of thermoplastic pipe and fittings. This test method is suitable for determination of dimensional compliance with product specifications.1.1 This test method covers the determination of diameter, wall thickness, and length dimensions of thermoplastic pipe. Included are procedures for measurement of the inside diameter of pipe intended to be joined by internal fittings, measurement of the average outside diameter for roundable pipe where out-of-roundness is not of primary concern, out-of-roundness measurement and measurement of the average outside diameter of non-roundable pipe, and for determining length and straightness.1.2 This test method also includes procedures for dimensioning molded thermoplastic pipe fittings.1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 156元 / 折扣价： 133 元 加购物车

3.1 This guide is not meant to be all inclusive since there are, and will continue to be, special circumstances that will dictate the use of nonconforming dimensions. These special circumstances and the requirements that they establish cannot be totally anticipated and therefore must be treated individually.3.2 These guidelines are based on an analysis of presently used materials for the manufacture of bow strings and the strength requirements dictated by archery bows falling within a draw weight range of 0 to 100 lb (0 to 444.8 N).3.3 These guidelines also address the desirability of proper fit of the arrow nock to the center serving.1.1 This guide covers the formulation of preliminary guidelines for the outside diameter dimensions of the center servings for the shooting strings for archery bows.1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification establishes requirements and test methods for dimensions and tolerances of central-vacuum hose inlet valve sockets. The requirements pertain to the dimensions, tolerances, and socket dimensions. The test methods include sampling and conditioning.1.1 This specification establishes requirements and test methods for dimensions and tolerances of central-vacuum hose inlet valve sockets.1.2 All notes and footnotes shall be considered as non-mandatory requirements of the specification.1.3 This specification does not apply to inlet valve back-up (or mounting) plates.1.4 This standard is applicable to universal valves marked with ASTM F2863, and does not limit proprietary valve designs.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

5.1 Injection Molding—In injection molding, the difference between the dimensions of a mold cavity and of the molded specimen may vary according to the design of the mold and operation of the molding process. Factors such as mold and melt temperature, fill times, and packing conditions are known to affect shrinkage significantly. Adherence to the specified mold design (see 7.1) and specifications outlined in Practice D3641 or ISO 294-4 or the appropriate material specification will improve the reproducibility of the test.5.2 Compression Molding—In compression molding, the difference between the dimensions of a mold cavity and of the molded specimen may vary according to the design of the mold and operation of the molding process. Factors, such as the amount of material in charge, cooling time, and pressure application are known to affect shrinkage significantly. Adherence to the specified mold design (see 7.2) and specifications outlined in Practice D4703 or ISO 293 or the appropriate material specifications will improve the reproducibility of the test.1.1 This test method is intended to measure shrinkage from mold cavity to molded dimensions of thermoplastics when molded by compression or injection processes with specified process conditions.1.2 This test method covers shrinkage measurements at 24 and 48 hours.1.3 This method will give comparable data based on standard specimens and can not predict absolute values in actual molded parts with varying flow paths, wall thicknesses, pressure and temperature gradients and process conditions. Differences in mold shrinkage may also be observed among the three specimen geometries described in this test method.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are given for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.NOTE 1: This standard and ISO 294-3 are equivalent in the design of specimen D2. This test method is equivalent to ISO 294-4 where Type D2 specimens and the procedure in Appendix X2 are used.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 571元 加购物车

定价： 590元 加购物车