定价： 646元 加购物车

定价： 590元 加购物车

4.1 The electrical behavior of rubber products used in particular applications is important for a variety of reasons such as safety, static changes, current transmission, etc. This test method is useful in predicting the behavior of such rubber products.1.1 This test method covers the determination of volume resistivity of rubbers used in electrically conductive and antistatic products.1.2 This test method assumes that the surface conductivity is negligible compared with the conductivity through the specimen.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

This test method covers the determination of ethylene diamine tetraacetate (EDTA) in soaps and synthetic detergents. Throughout this test method EDTA represents the hydrated disodium salt containing 2 moles of H 21.1 This test method covers the determination of ethylene diamine tetraacetate (EDTA) in soaps and synthetic detergents. Throughout this test method EDTA represents the hydrated disodium salt containing 2 moles of H2O. In the chemical literature this is frequently abbreviated to Na2H2Y4 · 2H2O.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

定价： 515元 加购物车

4.1 This practice is useful for the selection of zippers that will be compatible with items to be care labeled.4.2 This practice is useful as a guide for the selection of test methods to evaluate zipper properties that are relevant to care-labeled items.1.1 This practice provides guidelines to the manufacturer for the selection of zippers to be used in garments and household furnishings that have care labels. The use of this practice will facilitate the selection of a zipper compatible with the end-item requirements. In the absence of complete knowledge of end-item characteristics, it is not possible to stipulate specific universal characteristics for a care label. Therefore following initial selection, the chosen zipper should be tested in a prototype item to confirm its suitability. Zipper properties to be considered are those that may, following refurbishing, be the ones likely to adversely affect the continued use and enjoyment of the item in which the zipper is installed.1.2 The product characteristics evaluated by this practice are shrinkage, colorfastness, and ironing deformation.NOTE 1: Test methods of interest include Test Method D2052, Test Method D2053, Test Method D2054, Test Method D2057, Test Methods D2060.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

4.1 This practice is intended primarily for use by geotechnical engineers and technicians and geologists in the field, where the soil profile or samples from it may be observed in a relatively undisturbed (frozen) state.4.2 It may also be used in the laboratory to describe the condition of relatively undisturbed soil samples that have been maintained in a frozen condition following their acquisition in the field.4.3 The practice is not intended to be used in describing unfrozen soils or disturbed samples of frozen soil.1.1 This practice presents a procedure for the description of frozen soils based on visual examination and simple manual tests.1.2 It is intended to be used in conjunction with Test Method D2487 and Practice D2488, which describe and classify soils, but do not cover their frozen state.1.3 This procedure is based on “Guide to Field Description of Permafrost for Engineering Purposes,” National Research Council of Canada, 1963, and MIL-STD-619.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.5 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a project's many unique aspects. The word “Standard” in the title of this document means only that the document has been approved through the ASTM consensus process.

定价： 590元 加购物车

3.1 This guide directs the user to test methods that determine properties generally accepted as standard test items for classification of epoxy resins.1.1 This guide covers methods for testing epoxy resins as listed in Table 1. All of the methods were tested by interlaboratory participation in accordance with usual ASTM guidelines. Each method specifies a recommended amount of sample for starting a separate analysis, but several of the procedures can be conducted on the same starting material if so desired. For example, viscosity, color, and density could be run on the same specimen.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

5.1 Anionic surfactants are the most widely used of the synthetic detergents. ASTM methods in current use for their determination involve two-phase aqueous/chloroform titrations with the organic dyes methylene blue (Test Method D1681) or disulphine blue/dimidium bromide (Test Method D3049) as indicators. One advantage of the potentiometric method is that it eliminates the use of chloroform whose use is restricted for environmental and toxicological reasons.5.2 This test method is intended for use as described in 1.1.1.1 This test method describes a potentiometric titration procedure for determining the anionic active matter in detergents. It is intended for the analysis of anionic surfactants such as detergent range alkylbenzenesulfonates, α-olefin sulfonates, alcohol sulfates, and alcohol ethosulfates. It has not been tested for surfactant formulations.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.(A) Methylene blue method.(B) Mixed indicator method.

定价： 515元 加购物车

3.1 These test methods are suitable for setting specifications on linear detergent alkylates and for quality control where these alkylates are manufactured or are used in a manufacturing process.3.2 The gas chromatography test is useful in identifying linear detergent alkylates produced by the various manufacturing processes and for determining the applicability of a linear detergent alkylate to a particular end use. Test conditions have been optimized for resolution of the C-9 to C-15 linear detergent alkylates and the presence of higher or lower chain lengths will be readily apparent but may produce erroneous results. The tetralin structures have not been sufficiently identified to allow determination of tetralins, and small unidentified components are reported as tetralins and unidentifieds.3.3 Some linear detergent alkylates use a manufacturing process with an organic chloride as a precursor. This test may be used to ensure that the chloride content of the alkylate is not excessive for a particular end use.3.4 The platinum-cobalt color test is useful in determining that the color of the linear detergent alkylate will not contribute to the color of the end use product.3.5 The refractive index and specific gravity tests are possible aids in the identification of linear detergent alkylates and in evaluating alkylates for gross contaminants.3.6 The water test is suitable for determining that linear detergent alkylates do not contain amounts of water deleterious to further processing.1.1 These test methods cover chemical and physical tests applicable to linear detergent alkylates, evaluating those properties which characterize linear detergent alkylates with respect to its suitability for desired uses.NOTE 1: Linear detergent alkylates comprises linear alkylbenzenes prepared by varying processes of varying linear alkyl chain length. The alkylate is sulfonated for surfactant use, the largest application being in detergent products. Careful control of linear detergent alkylate characteristics is desired; during sulfonation, variations of the sulfonate can occur that may result in either desirable or undesirable end-use properties.1.2 The test methods appear as follows:  SectionComposition by Gas Chromatography  7 – 15Chlorides 16 – 27Color 28 – 30Refractive Index 31 – 33Specific Gravity 34 – 36Water 37 – 391.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage. See also Note 1 and Section 21.

定价： 590元 加购物车

4.1 This test method is suitable in research, development, and manufacturing control to monitor the level of citrate, a sequestering agent, in powder and liquid detergents.4.2 Accurate determination of sequestering agent is important in evaluating cost and performance of detergent products.1.1 This test method covers a potentiometric titration procedure for the determination of citrate in liquid and powder detergents.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage. Specific safety precautions are given in Section 8.

定价： 515元 加购物车

4.1 Alkylbenzene sulfonic acids are important intermediates in the synthetic detergent industry and are defined under “alkyl benzene sulfonate” in Terminology D459. This test method is suitable for the rapid monitoring of the sulfonic and sulfuric acid levels, both of which have a vital bearing on final product performance and appearance.1.1 This test method is applicable to the determination of sulfonic and sulfuric acids in branched and linear alkylbenzene sulfonic acids used as intermediates in synthetic detergents.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Material Safety Data Sheets are available for reagents and materials. Review them for hazards prior to usage.

定价： 515元 加购物车

5.1 Effective antifouling coatings are essential for the retention of speed and reduction of operating costs of ships. This test method is designed as a screening test to evaluate antifouling coating systems under conditions of hydrodynamic stress caused by water flow alternated with static exposure to a fouling environment. A dynamic test is necessary because of the increasing availability of AF coatings that are designed to ablate in service to expose a fresh antifouling surface. Because no ship is underway continually, a static exposure phase is included to give fouling microorganisms the opportunity to attach under static conditions. After an initial 30-day static exposure, alternated 30-day dynamic and static exposures are recommended as a standard cycle. The initial static exposure is selected to represent vessels coming out of drydock and sitting pierside while work is being completed. This gives the paint time to lose any remaining solvents, complete curing, absorb water, and, in general, stabilize to the in-water environment.5.2 This test method is intended to provide a comparison with a control antifouling coating of known performance in protecting underwater portions of ships’ hulls. This test method gives an indication of the performance and anticipated service life of antifouling coatings for use on seagoing vessels. However, the degree of correlation between this test method and service performance has not been determined.1.1 This test method covers the determination of antifouling performance and reduction of thickness of marine antifouling (AF) coatings by erosion or ablation (see Section 3) under specified conditions of hydrodynamic shear stress in seawater alternated with static exposure in seawater. An antifouling coating system of known performance is included to serve as a control in antifouling studies.1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For a specific hazards statement, see Section 8.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

5.1 Dry paint often comes in contact with itself especially in window and door areas and, depending on its hardness, the pressure, temperature, humidity, and duration of time the surfaces are in contact, sometimes sticks to itself (blocks). This stringent test method can be used to compare and rate subjectively the resistance of paints to blocking.1.1 This test method covers an accelerated procedure for evaluating the face-to-face blocking resistance of trades sales paints. This is not to be confused with blocking resistance Test Method D3003, which is concerned with blocking of industrial coatings on metal substrates, nor with Test Method D2793 which is concerned specifically with wood product finishes and reports results on a satisfactory or not satisfactory basis, rather than by the degree of blocking tendency as in this test method.1.2 The values stated in the SI units of measurement are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 515元 加购物车

4.1 The United Nations Committee of Experts on the Transport of Dangerous Goods in their recommended regulations place materials having a flash point below 23 °C (73.5 °F) in Packing Group II. However, if viscous substances such as paint and related coatings, adhesives, polishes, etc., meet certain requirements, they can be placed in Group III along with materials having a flash point between 23 °C and 60.5 °C (73.5 °F and 140 °F). One of the requirements is that less than 3 % of clear liquid separates from the bulk of the material when subjected to this test method.4.2 At the present time most international regulatory bodies such as the International Civil Aviation Organization (ICAO) and the International Maritime Organization (IMO) use the U.N. Recommendations. It is anticipated that most national transportation regulatory bodies will adopt the U.N. Recommendations as their regulations for control of transportation of hazardous materials. At present the United States permits the transshipment of hazardous materials through the United States to other countries under regulations of the IMO and ICAO.1.1 This test method covers the determination of the amount of liquid separated as an upper layer in a 24-h period from viscous solutions or dispersions that contain dispersed solids such as paints, enamels, pigmented lacquers, adhesives, polishes, and other similar materials.NOTE 1: The amount of clear liquid that separates during this test is one of the criteria in the United Nations Recommendations on the Transportation of Dangerous Goods2 for the placement of flammable viscous liquids into packing groups related to flash points (See 4.1).1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

3.1 This test method is suitable in research, development, and manufacturing control to monitor the level of NTA, a sequestering agent, in powder and liquid detergents.3.2 Accurate determination of a sequestering agent is important in evaluating cost and performance of detergent products.1.1 This test method describes the determination of nitrilotriacetates (NTA) in detergents.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific safety precautions, see 6.5.

定价： 515元 加购物车