定价： 43元 / 折扣价： 37 元 加购物车

定价： 38元 / 折扣价： 33 元 加购物车

定价： 59元 / 折扣价： 51 元 加购物车

定价： 475元 / 折扣价： 404 元 加购物车

定价： 333元 / 折扣价： 284 元 加购物车

定价： 190元 / 折扣价： 162 元

定价： 260元 / 折扣价： 221 元

5.1 The engineering function of many PM parts may require an exterior portion of the part to have a hardened layer. Where case hardening produces a distinct transition in the microstructure, metallographic estimation of the observed case depth may be used to check the depth to which the surface has been hardened.1.1 A metallographic method is described for estimating the observed case depth of ferrous powder metallurgy (PM) parts. This method may be used for all types of hardened cases where there is a discernible difference between the microstructure of the hardened surface and that of the interior of the part.1.2 With the exception of the values for grit size for which the U.S. standard designation is the industry standard, the values stated in SI units are to be regarded as standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 The engineering function of many PM parts may require an exterior portion of the part to have a specified case depth and microindentation hardness. Measurement of effective case depth is used to determine the depth to which the microindentation hardness of the exterior portion of a part has been increased over that of the interior of the part.1.1 This test method covers a procedure for determination of the effective case depth of powder metallurgy (PM) parts.1.2 A microindentation hardness traverse procedure is described to determine effective case depth. This test method may be used to determine the effective case depth for all types of hardened cases.1.3 The procedure for determining the microindentation hardness of powder metallurgy materials, as described in Test Method B933, shall be followed.1.4 Units—With the exception of the unit for density, for which the grams per cubic centimeter unit is the long-standing industry practice, the values in SI units are to be regarded as standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1.1 This test method covers determination of the microhardness of powder metallurgy (P/M) parts and applications of microhardness test results to methods for determination of the case depth. Technique for measurement of case depth of P/M parts by observation is also outlined. 1.2 Part A: Microhardness Measurement-This procedure covers test methods to determine the microhardness of P/M parts with the Knoop (HK) or the Vickers (HV) indenters. Procedures for surface preparation of the P/M material prior to microhardness measurement are included. 1.3 Part B: Case Depth Measurement-Procedures and methods for determination of both effective case depth and observed case depth for P/M parts are included. The principles of Part A on Microhardness Measurement are utilized to measure case depth. 1.4 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only. 1.5 This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

定价： 3913元 / 折扣价： 3327 元

15.1 For the purpose of determining compliance with the specified limits for requirements of the properties listed in the following table, an observed value or a calculated value shall be rounded as indicated in accordance with the rounding method of Practice E29.Property Rounded Unit for Observed or Calculated Value   Chemical Composition Nearest unit in the last right-hand significant digit used in expressing  the limiting valueGrain size:   Under 0.060 mm Nearest multiple of 0.005 mm 0.060 mm and over Nearest 0.01 mmAbstractThis specification establishes the requirements for annealed cartridge brass cups produced of Copper Alloy UNS No. C26000 for processing into for Type I and II cartridge cases, which are for small arms cartridge case cups and for artillery cartridge case cups, respectively. The material of manufacture shall be annealed plate, sheet, strip, or disks of wrought Alloy UNS No. 26000 processed to produce even-topped cups. The material shall be blanked and cupped to meet the cup dimensions specified, and subsequently annealed. The annealed cups shall be pickled, washed, and dried. The chemical and the grain size requirements are specified.1.1 This specification establishes the requirements for annealed cartridge brass cups produced of Copper Alloy UNS No. C26000 for processing into cartridge cases of the following types:1.1.1 Type I, for small arms cartridge case cups, and1.1.2 Type II, for artillery cartridge case cups.1.2 Units—The values stated in inch-pound units are to be regarded as standard, except for grain size, which is given in SI units. The values given in parentheses are mathematical conversions to SI units, which are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

定价： 481元 / 折扣价： 409 元 加购物车

定价： 1001元 / 折扣价： 851 元

定价： 1274元 / 折扣价： 1083 元