This specification establishes the requirements for copper-based brass or bronze centrifugal castings. Mechanical properties are determined from test bar castings and should meet the requirements listed herein. Brinell hardness readings should be taken on the grip end of tension test bars. All castings should not be repaired by welding without customer approval. UNS C95520 copper alloy castings are used in the heat treated condition only.1.1 This specification covers requirements for centrifugal castings of copper-base alloys having the nominal compositions shown in Table 1.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 The practice can be used to evaluate coupon materials of any composition, insofar as the coupon can be small enough to fit inside filter units mentioned in 4.1.5.2 This practice defines procedures that are quantitative, scalable, rapid, sensitive, and safe, while minimizing labor and addressing statistical confidence (1, 2).5.2.1 Quantitative—The total number of spores per coupon is determined by dilution-plating, and all spores remaining on the coupon are assayed for activity in the extraction tube to provide confidence that all the spores were accounted for.5.2.2 Statistical Confidence—The use of five independent preparations of spore inocula for a statistical n of 5.5.2.3 Sensitivity—Allows for complete detection of all culturable spores inoculated on a coupon, including the spores that remain attached to the coupon.5.2.3.1 The limit of detection is dependent on the culturability of fully matured spores to germinate, outgrow and divide in the presence of the extraction medium (1% tryptic soy broth, 100 mM L-Alanine, 1 mM inosine, 0.05% Tween 80) and/or on tryptic soy agar.5.2.3.2 Results presented in Refs (1, 3) (and currently unpublished results) indicate that these media, combined with the test temperatures and conditions described herein will generate results with a high level of practical confidence for detecting culturable Bacillus spores.5.2.4 Safety—Inoculated coupons are contained within filter units.5.2.5 Simplicity of Testing—Tests and extractions are performed in the same filter unit to minimize coupon handling steps.5.2.6 Scalable and Rapid—A maximum of 36 samples can be processed in 1 h by two technicians; a total of 300 samples have been processed by six technicians in 5 h (1, 2).5.2.7 Wide application for numerous Bacillus species and strains. The method has also been modified and used for vegetative bacteria and viruses as well (1, 2).1.1 This practice is used to quantify the efficacy of liquid or solid decontaminants on Bacillus spores dried on the surface of coupons made from porous and non-porous materials. This practice can distinguish between bactericidal and bacteriostatic chemicals within decontamination mixtures. This is important because many decontaminants contain both reactive compounds and high concentrations of bacteriostatic surfactants. All test samples are directly compared to pre-neutralized controls, un-inoculated negative growth controls, and solution controls on the same day as the test in order to increase practical confidence in the inactivation data.1.2 This procedure should be performed only by those trained in microbiological techniques, are familiar with antimicrobial (sporicidal) agents and the application instructions of the antimicrobial products.1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

This specification covers the requirements applicable to the design and construction of three classes of centrifugal pump (Class 1, Class 2, and Class 3) for shipboard application. When selecting material combinations, the conditions under which the various materials interact with each other shall be taken into consideration as well as the use of nonmetallic (composite) pump components where the use of that material can benefit the operation and maintenance of the pump. The requirements for the following are detailed: (1) pump design and construction, (2) pump operation (at or near the best efficiency point), (3) motor power ratings, (4) pitch and roll conditions, (5) horizontal pump and driver mounting, (6) vertical pump support, (7) bedplates, (8) pump couplings, (9) guards, (10) pumps with face-mounted motors, (11) shaft alignment, and (12) indication of direction of rotation. Pump design requirements for inlet and outlet connections, casings, radial and thrust bearings, journal and thrust bearings, rolling element bearings, mechanical seals, separate pressure boundary parts, and screw threads are specified. Requirements for paintings and coatings, equipment identification plates, and testing such as hydrostatic, mechanical run, performance, net positive suction head, vibration, and acoustic tests are also specified.1.1 This specification covers the requirements applicable to the design and construction of centrifugal pumps for shipboard application. The three classes of service covered by this specification are as follows:1.1.1 Class 1—Freshwater,1.1.2 Class 2—Seawater, and1.1.3 Class 3—Hydrocarbon pumps (less than 1500 SSU).1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

5.1 Manufacturers and users of alumina powders will find this test method useful to determine the particle size distribution of these materials for product specification, quality control, and research and development testing.1.1 This test method covers the determination of the particle size distribution of alumina in the range from 0.1 to 20 μm having a median particle diameter from 0.5 to 5.0 μm.1.2 The procedure described in this test method may be successfully applied to other ceramic powders in this general size range. It is the responsibility of the user to determine the applicability of this test method to other material.1.3 The values stated in SI units are to regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method provides a quantitative measure of the relative plasticizer absorption of general-purpose poly(vinyl chloride) resins under standard temperature conditions. Plasticizer sorption thus defined is one of the criteria useful for the description of the powder blend characteristics of poly(vinyl chloride) resins.1.1 This test method covers the determination of the plasticizer sorption of poly(vinyl chloride) (PVC) homopolymers using a controlled centrifugal force.1.2 The values stated in SI units are to be regarded as the standard.1.3 This test method references notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this test method.NOTE 1: This standard is equivalent to ISO 4608.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This specification covers the standard for aluminum-alloy centrifugal castings. This specification does not cover aluminum-alloy centrifugal castings used in aerospace applications. The castings shall be in accordance to the prescribed chemical composition. Chemical composition shall be determined by analyzing samples at the time the castings are poured, or samples taken from castings or tension test specimens. Unless otherwise stated, the tensile strength, yield strength and elongation of test specimens cut from casting shall be in accordance with the standards prescribed herein. If the specimens fail to conform to tension requirements, test bars representative of the castings may be retested in accordance with the replacement tests and retest provisions.1.1 This specification covers aluminum-alloy centrifugal castings designated as shown in Table 1.(A) When single units are shown, these indicate the maximum amounts permitted.(B) Analysis shall be made for the elements for which limits are shown in this table.(C) The following applies to all specified limits in this table: For purposes of determining conformance to these limits, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit in accordance with the rounding method of Practice E29.(D) In case of discrepancy between the values listed in Table 1 and those listed in the “Designations and Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (known as the ‘Pink Sheets’),” the composition limits registered with the Aluminum Association and published in the “Pink Sheets” shall be considered the controlling composition.(E) “Others” includes listed elements for which no specific limit is shown as well as unlisted metallic elements. The producer may analyze samples for trace elements not specified in the specification. However, such analysis is not required and may not cover all metallic “Others” elements. Should any analysis by the producer or the purchaser establish that an “Others” element exceeds the limit of “Each” or that the aggregate of several “Others” elements exceeds the limit of “Total,” the material shall be considered nonconforming.(F) Other Elements—Total shall be the sum of unspecified metallic elements 0.010 % or more, rounded to the second decimal before determining the sum.(G) If the iron content exceeds 0.45 %, manganese content shall not be less than one half of the iron.(H) For a cross reference of current and former alloy designations see the Aluminum Association’s “Designations and Chemical Composition Limits for Aluminum Alloys in the Form of Castings and Ingot (‘The Pink Sheets’).”1.2 This specification is for aluminum-alloy centrifugal castings used in general purpose applications. It may not address the mechanical properties, integrity testing, and verification required for highly loaded or safety critical applications.1.3 Alloy and temper designations are in accordance with ANSI H35.1/H35.1 (M).1.4 Unless the order specifies the “M” specification designation, the material shall be furnished to the inch-pound units.1.5 For acceptance criteria for inclusion of new aluminum and aluminum alloys and their properties in this specification, see Annex A1 and Annex A2.1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

Manufacturers and users of advanced ceramic powders will find this test method useful for determining the particle size distribution of these materials for product specification, quality control, and research and development. 1.1 This test method covers determination of the particle size distribution of advanced ceramic powders specifically silicon nitride and carbides, in the range of 0.1 to 20 μm, having a median particle diameter from 0.5 to 5.0 μm. 1.2 The procedure described in this test method may be applied successfully to other ceramic powders in this general size range, provided that appropriate dispersion procedures are developed. It is the responsibility of the user to determine the applicability of this test method to other materials. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

4.1 The mechanical properties determined from test bars for sand, permanent mold, and centrifugal castings poured in accordance with this practice represent the properties of the metal going into castings poured from the same heat. These mechanical properties may not be the same as the properties of the corresponding castings because of the solidification effects of varying size, section, and design.4.2 Test bars for continuous castings are taken from the castings and therefore represent the properties of the castings.1.1 This practice establishes procedures for preparing test coupons and specimens (machined and unmachined) for tension tests of copper alloys for sand, permanent mold, centrifugal and continuous castings.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车