5.1 The height of surface profile has been shown to be a factor in the performance of various coatings applied to steel. For this reason, surface profile should be measured prior to coating application to ensure conformance of a prepared surface to profile requirements specified by the manufacturer of a protective coating or the coating job specification.NOTE 2: The peak count/peak density has been shown to be a factor in the performance of various coatings applied to steel. According to research performed by Roper, Weaver and Brandon6, an increase in peak count can improve the adhesion of some coatings to the prepared steel, as well as provide greater resistance to corrosion undercutting once the coating becomes damaged in service.NOTE 3: Optical microscope methods serve as a referee method for surface profile measurement methods A and B. Profile depth designations are based on the concept of mean maximum profile (h max); this value is determined by averaging a given number (usually 20) of the highest peak to lowest valley measurements made in the field of view of a standard measuring microscope. This is done because of evidence that coating performance in any one small area is primarily influenced by the highest surface features in that area and not by the average roughness.71.1 These test methods cover the description of techniques for measuring the profile of abrasive blast cleaned surfaces in the field, shop, and laboratory. There are other techniques suitable for laboratory use not covered by these test methods.1.2 Method B may also be appropriate to the measurement of profile produced by using power tools.NOTE 1: The Method B procedure in this standard was developed for use on flat surfaces. Depending on the radius of the surface, the results could have greater variability with lower values and averages.1.3 SSPC standard SSPC-PA 17 provides additional guidance for determining conformance with surface profile requirements.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This method may be useful in assuring conformance of a prepared surface to profile requirements specified by the manufacturer of a protective coating.5.2 This method includes determination of the peak density (number of profile peaks in a specified distance). Some workers in the field believe that optimizing peak height and peak density can improve coating adhesion.5.3 This method allows specifiers to objectively define surface texture after abrasive blast cleaning rather than using subjective terms such as “angular pattern” or “dense and uniform pattern.”5.4 Because implicit and explicit definitions of “roughness” may differ substantially, numerical characterizations of profile cannot be compared directly across different methods.1.1 This test method describes a shop or field procedure for determination of roughness characteristics of surfaces prepared for painting by abrasive blasting. The procedure uses a portable skidded or non-skidded stylus profile tracing instrument. The measured characteristics are: Rt and Rpc. Additional measures of profile height (Rmax and/or Rz) may also be obtained as agreed upon by purchaser and seller. (The digitally-determined profile parameters Rt, Rmax, Ry and Rzlmax are extremely similar in definition.)1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.3 In general, this method should be limited to the measurement of surface roughness where Rt is in the range 10 to 150 μm (0.4 to 6 mil) and where the Peak Count, Rpc is less than 180 peaks/cm (450 peaks/in.).1.4 SSPC standard SSPC-PA 17 provides additional guidance for determining conformance with surface profile requirements.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 0元 / 折扣价： 0 元

3.1 Chemical cleaning and etching is used to prepare concrete for coating.3.2 Residual chemicals not removed by water rinsing may adversely affect the performance and adhesion of coatings applied over prepared concrete surfaces. It is the intent of this test method to determine that residual chemicals have been removed by measuring the acidity or alkalinity of the final rinsed surface.1.1 This test method covers procedures for determining the acidity or alkalinity of concrete surfaces prepared by chemical cleaning or etching prior to coating.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 This test method will provide an indication of the effectiveness of the cleaning system at restoring the appearance of an artificially soiled carpet by wet extraction cleaning. The cleaning effectiveness in the laboratory test may not be the same as in home cleaning due to variations in the homes, carpets, soils, and other factors.4.2 In order to provide a uniform basis for measuring the performance described in 1.1, standardized test carpet, test pad, and test soil are employed in this procedure.1.1 This test method provides only a laboratory test for visually determining the relative carpet cleaning effectiveness of a wet extraction cleaning system when tested under standard conditions.1.2 This test method is applicable to types of upright, canister, and combination wet extraction cleaners and their recommended chemical cleaning formulas intended for cleaning carpets as a primary or secondary function. This test method excludes pre-spray systems or pre-spray treatments.1.3 This test method is not applicable to upholstery cleaning or bare floor cleaning.1.4 This test method applies only to the cleaning of embedded soil from carpet, not the removal of surface litter and debris.1.5 This test method does not directly quantify the amount of soil removed but is visually assessed by employing colorimetric instrumentation.1.6 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车