定价： 1515元 / 折扣价： 1288 元

定价： 689元 / 折扣价： 586 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 975元 / 折扣价： 829 元 加购物车

定价： 156元 / 折扣价： 133 元

定价： 605元 / 折扣价： 515 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

Purpose and Scope 1.1 Mobile equipment such as tractors and self-propelled sprayers are often used in agricultural operations where pesticides are present. Such operations usually require the operator to use personal protective equipment (PPE). The ty

定价： 319元 / 折扣价： 272 元

3.1 The purpose of this guide is to establish criteria for the design of gloveboxes as primary confinement systems to ensure the safety of the workers and the protection of the environment when storing, handling, processing, and disposing of both combustible and non-combustible forms of plutonium. The use of this guide will provide the user with guidance to design a successfully performing glovebox system.1.1 This guide defines criteria for the design of glovebox systems to be used for the handling of plutonium in any chemical or physical form or isotopic composition or when mixed with other elements or compounds. Not included in the criteria are systems auxiliary to the glovebox systems such as utilities, ventilation, alarm, and waste disposal. Also not addressed are hot cells or open-face hoods.1.2 The scope of this guide excludes specific license requirements relating to provisions for criticality prevention, hazards control, safeguards, packaging, and material handling. Observance of this guide does not relieve the user of the obligation to conform to all federal, state, and local regulations for design and construction of glovebox systems.1.3 Units—The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This practice provides one means for determining the aeroplane structural loads for flight, control surfaces, and control systems. This practice satisfies the simplified loads requirements set forth in Specification F3116/F3116M for Normal Category Aeroplanes.1.1 This practice provides an acceptable means of meeting the airworthiness requirements for the flight design loads and conditions of small normal category level 1 and 2 aeroplanes. The material was developed through open consensus of international experts in general aviation. This information was created by focusing on Normal Category aeroplanes. The content may be more broadly applicable; it is the responsibility of the applicant to substantiate broader applicability as a specific means of compliance. The topics covered within this practice are: Simplified Design Load Criteria, Acceptable Methods for Control Surface Loads Calculations, Acceptable Methods for Primary Control System Loads Calculations, and Control Surface Loading (Level 1 Aeroplanes).1.2 This practice is applicable to normal category, low-speed, level 1 and 2 aeroplanes. Use of the term aeroplane used throughout this practice will mean “normal category, low-speed, level 1 or 2 aeroplane,” unless otherwise stated.1.3 An applicant intending to propose this information as means of compliance for a design approval must seek guidance from their respective oversight authority (for example, published guidance from applicable CAAs) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this standard (in whole or in part) as an acceptable means of compliance to their regulatory requirements (hereinafter “the Rules”), refer to the ASTM Committee F44 web page (www.astm.org/COMMITTEE/F44.htm).1.4 This document may present information in either SI units, English Engineering units, or both. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 / 折扣价： 550 元 加购物车

1. Scope This International Standard specifies test methods and acceptance criteria for evaluating the electromagnetic compa tibility of tractors and all kinds of mobile (including hand-held) agricultural machinery, forestry machinery, landscaping and

定价： 956元 / 折扣价： 813 元

ISO/IEC 15408 is meant to be used as the basis for evaluation of security properties of IT products and systems. By establishing such a common criteria base, the results of an IT security evaluation will be meaningful to a wider audience.

定价： 1274元 / 折扣价： 1083 元

定价： 2275元 / 折扣价： 1934 元

定价： 2412元 / 折扣价： 2051 元