定价： 689元 / 折扣价： 586 元

定价： 1632元 / 折扣价： 1388 元

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 605元 / 折扣价： 515 元 加购物车

定价： 689元 / 折扣价： 586 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

定价： 689元 / 折扣价： 586 元

定价： 156元 / 折扣价： 133 元 加购物车

定价： 689元 / 折扣价： 586 元 加购物车

3.1 Portable hardness testers are used for testing materials that because of their size, location or other requirements such as test point are unable to be tested using traditional fixed instruments.3.2 Portable hardness testers, by their nature, induce variation that could influence the test results; therefore, hardness measurements made in accordance with this test method are not considered to meet the requirements of E10 or E18. The user should compare the results of the precision and bias studies in E110, E10 and E18 to understand the differences in results expected between portable and fixed instruments.3.3 Two test parameters that can significantly influence the measurement accuracy when using portable hardness testers are the alignment of the indenter to the test surface and the timing of the test forces. The user is cautioned to do everything possible to keep the centerline of the indenter perpendicular to the test surface and to apply the test forces using the same time cycle as defined in Test Method E10 or Test Methods E18.3.4 Portable hardness testers are delicate instruments that are subject to damage when they are moved from one test site to another. Therefore, repeating the daily verification process during the testing sequence is recommended to insure that they are working properly.3.5 Hardness testing at a specific location on a part may not represent the physical characteristics of the whole part or end product.AbstractThis test method establishes the standard procedures, including the calibration, precision and bias of the apparatus used, for the determination of indentation hardness of metallic materials by means of portable hardness testers.1.1 This test method defines the requirements for portable instruments that are intended to be used to measure the Rockwell or Brinell hardness of metallic materials by performing indentation tests on the surface of materials in the field or outside of a test lab, or in cases where the size or weight of the test piece prevents it from being tested on a standard E10 or E18 hardness tester.1.2 The principles used to measure the Rockwell or Brinell hardness are the same as those defined in the E18 standard test method for Rockwell or E10 standard test method for Brinell.NOTE 1: Standard test methods E10 and E18 will be referred to in this test method as the standard methods.1.3 The portable hardness testers covered by this test method are verified only by the indirect verification method. Although the portable hardness testers are designed to employ the same test conditions as those defined in the standard test methods, the forces applied by the portable Rockwell and Brinell testers and the depth measuring systems of the portable Rockwell testers may not meet the tolerance requirements of the standard methods. Portable hardness testers shall use indenters that meet the requirements of the standard test methods.1.4 This test method does not apply to portable hardness testers that measure hardness by a means or procedure that is different than those defined in E10 or E18 For example, this test method does not apply to the methods defined in ASTM standard Practice A833, Test Methods A956 and A1038 or B647.1.5 A report section is included to define how to indicate that the test result was obtained by using a portable device that conforms to this document.1.6 Annex A1 is included that defines the periodic indirect verification and daily verification requirements for these instruments.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1 Scope This clause of part 1 is replaced by: This standard deals with the safety of portable electric heating tools and similar appliances, their rated voltage being not more than 250 V. Appliances not intended for normal household use, but whic

定价： 637元 / 折扣价： 542 元

5.1 Measurements of RI made by this test method, with the 0.2° observation angle, are related to visual observation of raised retroreflective pavement markers at distances of approximately 220 m (720 ft) for cars or approximately 440 m (1440 ft) for trucks when illuminated by tungsten filament light sources such as car headlights.5.2 There are some castings that block vehicle illumination of a portion of the marker mounted within it. In this case, measured RI can be significantly lower than when the marker is photometered outside the casting, but will correspond to the visual observation.5.3 The test method is not applicable to raised pavement markers mounted in depressions cut into the pavement.5.4 The coefficient of luminous intensity of raised retroreflective pavement markers degrades with traffic wear and requires periodic measurement to ensure that sufficient visibility is provided to the driver.5.5 The quality of the pavement markers as to materials used, age and wear pattern, will have an effect on the coefficient of (retroreflected) luminous intensity. These conditions need to be observed and noted by the user.1.1 This test method covers the measurement of the retroreflective properties of raised retroreflective pavement markers at a prescribed geometry, by means of a portable retroreflectometer that can be used in the field. The measurements can be compared to minimum requirements to determine the need for replacement.1.2 The observation angle specified for retroreflectometers in this test method is that currently specified for raised pavement markers in the United States and may differ from the angles used elsewhere. For other jurisdictions, replace the observations angle specified herein with the observation angle specified by the pertinent agency.1.3 This test method is intended to be used for field measurement of raised retroreflective pavement markers but may also be used to measure the performance of new markers before they are placed in the field.1.4 This test method covers measurements of raised pavement markers mounted on a road surface or mounted in snow-plowable metal castings.1.5 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

1. Scope 1.1 This Standard applies to kerosine-fuelled appliances with capacities up to 4400 W that are primarily used as portable space heating appliances. 1.2 Appliances with input capacities greater than 4400 W may be examined and tested in acc

定价： 455元 / 折扣价： 387 元

定价： 260元 / 折扣价： 221 元 加购物车