3.1 This specification provides designers and manufacturers of electric propulsion for light sport aircraft design references and criteria to use in designing and manufacturing EPUs.3.2 Declaration of compliance is based on testing and documentation during the design, ground testing and flight testing of the EPU by the manufacturer or under the manufacturers’ guidance.3.3 Manufacturers of the EPUs are encouraged to review and incorporate appropriate standards and lessons learned from ground based systems as documented in SAE J2344 and EASA CRI F-58 (see Appendix X2).3.4 Electric aircraft may contain potentially hazardous level of electrical voltage or current. It is important to protect persons from exposure to this hazard. Under normal operating conditions, adequate electrical isolation is achieved through physical separation means such as the use of insulated wire, enclosures, or other barriers to direct contact. There are conditions or events that can occur outside normal operation that can cause this protection to be degraded. Some means should be provided to detect degraded isolation or ground fault. In addition, processes or hardware, or both, should be provided to allow for controlled access to the high voltage system for maintenance or repair. A number of alternative means may be used to achieve these electrical safety goals including automatic hazardous voltage disconnects, manual disconnects, interlock systems, special tools and grounding. The intention of all these means is either to prevent inadvertent contact with hazardous voltages or to prevent damage or injury from the uncontrolled release of electric energy. Lightning strikes are not addressed in this Standard Practice because LSA aircraft are limited to VMC flight only.1.1 This practice covers minimum requirements for the design and manufacture of Electric Propulsion Units (EPU) for light sport aircraft, VFR use. The EPU shall as a minimum consist of the electric motor, associated controllers, disconnects and wiring, an Energy Storage Device (ESD) such as a battery or capacitor, or both, and EPU monitoring gauges and meters. Optional onboard charging devices, in-flight charging devices or other technology may be included.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Comparison of brake horsepower developed and of specific fuel consumption rates from engine to engine may be made by use of data based upon a standard for composition of an engine assembly.4.2 The purchaser of the engine assembly will be fully advised of the minimum scope of assembly which the purchaser may rightfully expect to be encompassed by a response to a request for quotation and to be delivered in response to a purchase order unless the engine builder in the proposal or in the offer to sell has clearly advised otherwise.4.3 It will be made apparent to the purchaser that additional auxiliary and accessory equipment will be needed to supplement the defined engine assembly when full consideration is given to the application of the engine assembly as a prime mover in a specific vessel.1.1 This guide covers performance and minimum scope of assembly of all medium speed marine diesel engines intended for main propulsion of single or multiple screw propelled marine vessels or for vessels using other than screw propeller-type main propulsion.1.2 This guide is intended to supplement the regulations of legally constituted regulating authorities. In the event of any conflict, which may become apparent after publication of this guide, with such legally constituted regulations, the latter shall take precedence, as may be applicable within the jurisdiction of such authorities and specific to each case, unless such latter regulations are formally waived by proper cognizant authority.1.3 This guide is not intended to relieve the purchaser of the obligation fully to advise the engine builder of all of the purchaser’s unique operational considerations to allow those considerations to be satisfied.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification addresses airworthiness requirements for the design and installation of electric propulsion systems for aeroplanes. Hybrid-electric propulsion systems are addressed implicitly unless explicitly stated otherwise. This specification was written with the focus on electric propulsion systems with conventional system layout, propulsion characteristics, and operation. The content may be more broadly applicable; it is the responsibility of the applicant to substantiate broader applicability as a specific means of compliance.1.2 An applicant intending to propose this information as Means of Compliance for a design approval must seek guidance from their respective oversight authority (for example, published guidance from applicable CAAs) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this standard (in whole or in part) as an acceptable Means of Compliance to their regulatory requirements (hereinafter “the Rules”), refer to the ASTM Committee F44 web page (www.astm.org/COMMITTEE/F44.htm). Annex A1 maps the Means of Compliance described in this specification to EASA CS-23, amendment 5, or later, and FAA 14 CFR Part 23, amendment 64, or later.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification applies to the electrical systems, electrical equipment, and electrical power distribution aspects of airworthiness and design for aircraft with electric or hybrid-electric propulsion. Developed through open consensus of international experts in general aviation, this material focused on Normal Category Airplanes. The content may be more broadly applicable; it is the responsibility of the applicant to substantiate broader applicability as a specific means of compliance.This specification establishes the Aircraft Type Code (ATC) compliance matrix based on certification level, number of engines, type of engine(s), stall speed, cruise speed, meteorological conditions, altitude, and maneuvers. An ATC is defined by taking into account both the technical considerations regarding the design of the aircraft and the airworthiness level established based upon risk-based criteria. Requirements for electrical systems for electric propulsion cover power source capacity and distribution, electrical systems and equipment, circuit protective devices, master switch arrangement, switches, electrical cables and equipment, electrical system fire protection, electronic equipment, and storage battery design and installation.1.1 This specification covers the electrical systems, electrical equipment, and electrical power distribution aspects of airworthiness and design for aircraft with Electric or Hybrid-Electric Propulsion. This specification was written with the focus on electric propulsion systems with conventional system layout, characteristics, and operation. This specification does not address all of the requirements that may be necessary for possible hybrid-electric configurations where an EPU and a combustion engine are used in combination to provide propulsion. The use of this specification combined with the applicable portions of Specification F3231/F3231M may be necessary for hybrid-electric configurations. This material was developed through open consensus of international experts in general aviation. This material was created by focusing on Normal Category Aeroplanes. The content may be more broadly applicable; it is the responsibility of the applicant to substantiate broader applicability as a specific means of compliance.1.2 An applicant intending to propose this information as a means of compliance for design approval shall seek guidance from their respective oversight authority (for example, published guidance from applicable CAAs) concerning the acceptable use and application thereof. For information on which oversight authorities have accepted this standard (in whole or in part) as a Means of Compliance to their regulatory requirements (Hereinafter referred to as “the Rules”), refer to ASTM F44 webpage (www.ASTM.org/COMMITTEE/F44.htm).1.3 Units—This standard may present information in either SI units, English Engineering units, or both. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车