定价： 345元 / 折扣价： 294 元

定价： 345元 / 折扣价： 294 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

定价： 0元 / 折扣价： 0 元 加购物车

1.1 This specification covers needle roller bearings having thick outer rings, with rollers and cages.1.2 The bearings being specified are intended to be used with hardened shafts (HRC58-65; see Test Methods E18). For use with unhardened shafts, bearings should be used in conjunction with inner bearing ring MS51962 as specified in Specification F2431 and shown as MS500072 bearing assemblies in Specification F2430.1.3 The use of recycled materials that meet the requirements of the applicable material specification without jeopardizing the intended use of the item is encouraged.1.4 Bearings designed to this specification are intended for use in applications requiring high radial load with minimal angular shaft misalignment.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.NOTE 1: This specification contains many of the requirements of MS51961 which was originally developed by the Department of Defense and maintained by the Defense Supply Center Richmond.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers requirements for rigid or flat seat type, two channeled race surface, thrust roller bearings intended for use in slow rotating or oscillating applications where pure thrust loads are applied. The thrust bearing shall be made of the specified high carbon chromium alloy steel. Requirements for (1) physical properties such as heat treatment, (2) dimensions and mass, and (3) surface finish are specified. Dimensions of retainer type, steering gear service and retainerless type, intermittent operation, are illustrated.1.1 This specification covers requirements for rigid or flat seat type, two channeled race surface, thrust roller bearings.1.2 Intended Use—The bearings covered in this specification are intended for use in slow rotating or oscillating applications where pure thrust loads are applied.1.3 This specification contains many of the requirements of MS17169, which was originally developed by the Department of Defense and maintained by the Defense Supply Center in Richmond. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2Preparing Activity Custodians Review ActivitiesDLA-GS4 Army-AT Army-MI  Navy-MC Air Force-84  Air Force-99    DLA-GS4  1.4 For design feature purposes, this specification takes precedence over procurement documents referenced herein.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 Paint spatter generated by roller application is dependent on the properties of both the paint being applied and the paint roller cover used for the application. To eliminate the influence of the paint roller cover as a variable, and thus restrict the spatter-inducing variable to the paint under test only, the paint roller cover is replaced by a standard notched spool roller to generate spatter by a mechanism that simulates that of a paint-applying roller cover.4.2 Although most of the development work to establish this test method was undertaken using latex paints, sufficient work was also done to show its applicability to solvent-reducible paints.4.3 Tests during the development of this test method showed that the spattering properties of paints, like other physical properties, may in time change. Therefore, the results of this test are valid only for the time when the test is run.1.1 This test method covers the determination of the tendency of a paint to spatter when applied with a paint roller to a substrate.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This specification covers requirements for metric series, tapered roller bearings with a single row of rollers.1.2 Intended Use—The bearings covered in this specification are intended to be used in general industrial and vehicle applications where the operating temperature does not exceed 120 °C (250 °F).1.3 This specification contains many of the requirements of DS3225, which was originally developed by the Department of Defense and maintained by the Defense Supply Center in Richmond. The following government activity codes may be found in the Department of Defense, Standardization Directory SD-1.2Preparing Activity Custodians Review ActivitiesDLA-GS4 Army-AT Army-AV  Navy-MC Navy –MC, SH  Air Force-99 Air Force-84    Other-NS1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 Laboratory measurement of application properties of architectural coatings generally employ a blade-type applicators that lay down films of highly uniform thickness. Applicators, such as brushes and rollers, typically apply films that lack uniformity due to variations in rheology, film build, flow and leveling properties resulting in the practical hiding of most paints being less than that measured on films applied with a blade-type applicator. This guide provides an indication of the actual application properties of the paint, as applied by a contractor or consumer.1.1 This guide describes procedures for the application of brush or roller, or both, applied paint films to sealed wallboard for evaluating application properties.1.2 Because both the application and panel evaluation are subjective, this guide should be used only for comparative testing within one laboratory using one operator for each set of applications, as the ratings assigned by different laboratories may not agree.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

5.1 This test method is intended to be used for determining the consistency and density of stiff to extremely dry concrete mixtures common in roller-compacted concrete construction.5.1.1 Because of the stiff to extremely dry consistency of some roller-compacted concrete mixtures, the standard Vebe test method of rodding the specimen in a slump cone is substituted by Procedures A and B.85.2 Procedure A uses a 22.7 kg [50 lb] surcharge and is used for concrete consolidated by roller-compaction methods when the consistency of the concrete is very stiff to extremely dry.5.3 Procedure B uses a 12.5 kg [27.5 lb] surcharge and is used for concrete consolidated by roller-compaction methods when the consistency of the concrete is stiff to very stiff consistency, but not extremely dry.1.1 This test method is used to determine the consistency of concrete using a vibrating table and a surcharge and to determine the density of the consolidated concrete specimen. This test method is applicable to freshly mixed concrete, prepared in both the laboratory and the field, having a nominal maximum size aggregate of 50 mm [2 in.] or less. If the nominal maximum size of aggregate is larger than 50 mm [2 in.], the test method is applicable only when performed on the fraction passing the 50-mm [2-in.] sieve with the larger aggregate being removed in accordance with Practice C172.1.2 This test method, intended for use in testing roller-compacted concrete, may be applicable to testing other types of concrete such as cement-treated aggregate and mixtures similar to soil-cement.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this standard.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.2)1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This practice is intended to be used for stiff to extremely dry concrete mixtures commonly used in roller-compacted concrete construction. This practice is used instead of rodding or internal vibration, which cannot properly consolidate concrete of this consistency (Note 1).NOTE 1: Further description of this concrete consistency is given in ACI 207.5 Roller-Compacted Mass Concrete3 and 211.3 Guide for Selecting Proportions for No-Slump Concrete3. The consistency of roller-compacted concrete may be determined in accordance with Test Method C1170/C1170M.1.1 This practice covers procedures for making cylindrical test specimens from concrete when the standard procedures of rodding and internal vibration, as described in Practice C31/C31M, are not practicable. This practice is applicable to freshly mixed concrete, prepared in the laboratory and the field, having a nominal maximum size aggregate of 50 mm [2 in.] or less. If the nominal maximum size aggregate is larger than 50 mm [2 in.], the practice is applicable only when performed on the fraction passing the 50-mm [2-in.] sieve with the larger aggregate being removed in accordance with Practice C172. This practice, intended for use in testing roller-compacted concrete, may be applicable to testing other types of concrete such as cement-treated aggregate and mixtures similar to soil-cement.1.2 Two methods are provided for making concrete cylinders using a vibrating table:1.2.1 Method A is a procedure for making test specimens in steel reusable molds attached to a vibrating table.1.2.2 Method B is a procedure for making test specimens in single-use plastic molds that have been inserted into a metal sleeve attached to a vibrating table.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 The text of this practice refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this practice.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This practice, intended for use in testing roller-compacted concrete, may be applicable to testing other types of cementitious material such as coarse-grained, soil-cement. This practice provides standardized requirements for molding stiff to very dry consistency concrete mixtures commonly used in roller compacted concrete construction. This practice is used instead of rodding or internal vibration, which cannot properly consolidate concrete of this consistency.NOTE 1: Further description of roller compacted concrete consistency is given in ACI 207.5R and ACI 211.3. The consistency of concrete using a vibrating table may be determined in accordance with Test Methods C1170/C1170M.4.2 This practice is used to mold cylindrical test specimens commonly used for testing compressive or tensile strength of concrete. Specimens tested for compressive strength and splitting tensile strength shall be in accordance with Test Methods C39/C39M and C496/C496M, respectively. Test specimens also may be used to determine density of fresh concrete.NOTE 2: For some extremely dry mixtures; (those with a consistency greater than 45 s when tested in accordance with Test Methods C1170/C1170M)5 the density of specimens made in accordance with this practice may be greater than the in-place density of roller-compacted concrete due to the greater potential for voids at the bottom of the lifts in the field.NOTE 3: The mass of the apparatus and amount of force applied by the operator may significantly affect the density of specimens made from these mixtures; thus, discretion is advised when interpreting test results on specimens made according to this practice.1.1 This practice2 covers molding cylindrical test specimens from concrete when the standard procedures of rodding and internal vibration, as described in Practice C31/C31M and Practice C1176/C1176M, are not practicable. This practice is applicable to freshly-mixed concrete, prepared in the laboratory and the field.1.2 Freshly-mixed concrete is molded in cylindrical molds using an electric vibrating hammer equipped with a shaft and circular plate.1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.4 The text of this practice references notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of this practice.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers performance requirements for helmets manufactured for use by recreational bicyclists or roller skaters. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance standard and is not intended to restrict design. Helmets shall be impacted with anvils centered on or above the prescribed test line. The test anvils can be oriented in any horizontal, centered position. One each hot, cold, wet, and ambient helmet shall be impacted using the flat and hemispherical anvils only. The curbstone anvil shall be used to impact one time each of the second set of four samples, one conditioned under each of the four conditioning environments. The peak acceleration of the impulse during the impact shall be measured. The ambient helmet shall be subjected to the positional stability (roll-off) test, while the hot, cold, and wet helmets shall be subjected to the dynamic strength retention test.1.1 This specification covers performance requirements for helmets manufactured for use by recreational bicyclists or roller skaters. This specification recognizes the desirability of lightweight construction and ventilation; however, it is a performance standard and is not intended to restrict design.1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein.1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the standard and should not be sold with any indication that it meets parts of the standard.1.4 This standard is subject to revision at any time by ASTM. It must be reviewed every five years and if not revised either reapproved or withdrawn. References to the standard must include the version date. No references to a version that has been replaced or withdrawn shall be placed on any product or its packaging manufactured more than 24 months after the effective revision or withdrawal date. Go to astm.org to verify the latest version of this standard.NOTE 1: The current edition of this standard was approved on June 1, 2018.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

This guide deals with the provisions for consistent safety considerations in the design and construction of new roller hockey rinks in order to reduce potential safety hazards. It is projected to standardize game conditions; establish guidelines that will provide a level of conformity for the purpose of competition and reduce potential hazards to players and game officials; and applies to the development of new arenas and to existing facilities that will be renovated. This guide takes into consideration that most ice hockey rinks with concrete surfaces can be acceptable for roller hockey. However, dasher boards must meet criteria respective of the specific activity. Facilities designed and constructed for roller hockey may not be acceptable for ice hockey use. Included in this guide are the structures and environment, player's bench and box, penalty benches and box, off-rink official's bench/box, signal and timing devices, dressing rooms, nets, rink floor design, illumination, emergency medical care, and signage.1.1 This guide covers the provisions for consistent safety considerations in the design and construction of new roller hockey rinks in order to reduce potential safety hazards. It is intended to standardize game conditions and establish guidelines that will provide a level of conformity for the purpose of competition and reduce potential hazards to players and game officials.1.2 This guide should be taken into consideration by architects, designers, engineers, construction contractors, and appropriate inspectors who may be involved in the design and construction of new roller hockey rinks. This guide applies to the development of new arenas and to existing facilities that will be renovated.1.3 This guide takes into consideration that most ice hockey rinks with concrete surfaces can be acceptable for roller hockey. However, dasher boards must meet criteria respective of the specific activity. Facilities designed and constructed for roller hockey may not be acceptable for ice hockey use.1.4 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 This test method is intended to simulate the slip of a flexible web on a roller in a machine or tribosystem that conveys web materials. Flexible webs such as plastic sheeting, paper, elastomers, metal foils, and cloth are often transported in manufacturing processes by combinations of driving and idler rollers. The friction characteristics of the web/roller interface often affects the web transport process. If the web/roller friction is too low, the web can slip on the rollers and be damaged or damage the roller. High friction on the other hand, can lead to steering problems and overloading of driving motors.5.2 This test method can be used to rank rollers for their ability to resist slip versus a particular web material (high friction). Conversely this test method can assess web materials or web surface coatings such as waxes and lubricants. In this latter case, the goal may be a low-friction product made from a web (film, magnetic media, paper, and so forth).5.3 If a tribosystem involves transport of a flexible web on a roller, this is an appropriate test to use to measure the friction characteristics of the roller/web couple.1.1 This test method covers the simulation of a roller/web transport tribosystem and the measurement of the static and kinetic coefficient of friction of the web/roller couple when sliding occurs between the two. The objective of this test method is to provide users with web/roller friction information that can be used for process control, design calculations, and for any other function where web/roller friction needs to be known.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车