定价： 646元 加购物车

This specification covers eye protectors, designed for use by players of racket sports, women's lacrosse, field hockey, basketball, baseball, and soccer that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by racket-sport rackets and balls, women's lacrosse and field hockey sticks and balls, baseballs, soccer balls, hands, elbows, and fingers. Protective eyewear offers protection only to the eyes and does not protect other parts of the head. Protectors are divided into four types depending on their design characteristics as follows: Type I—A protector with the lens or lenses and frame frontpiece molded as one unit. Frame temples or other devices, such as straps, to affix the lens/frontpiece may be separate pieces; Type II—A protector with a single lens or lenses, either plano or prescription, mounted in a frame that was manufactured as a separate unit; Type III—A protector without a lens; and Type IV—A full or partial face shield. Materials shall be tested using optical tests such as field of view, optical quality, luminous transmittance, prismatic deviation measurements, haze, refractive power measurements, surface imperfections and internal defects, and alternate optical tests; and mechanical tests such as high velocity impact resistance, and projectile simulator test. In addition, the individual grades shall conform to the general, and performance requirements.1.1 This specification covers eye protectors, designed for use by players of basketball, baseball, and soccer to minimize or significantly reduce injury to the eye and adnexa due to impact and penetration by baseballs and softballs, basketballs, soccer balls, hands, elbows, and fingers. Protective eyewear offers protection only to the eyes and adnexa and does not protect other parts of the head.1.2 Protectors are divided into three types depending on their design characteristics.1.3 This specification applies to eye protectors for use by wearers of corrective lenses and also by those players who do not require prescription eyewear. (Warning—Polycarbonate or Trivex spectacle lenses should be used if spectacles are worn under protective eyewear.)1.4 In this standard, the use of the words “shall” or “must” indicates a mandatory requirement. The word “should” indicates a recommendation.1.5 Failure of the product occurs when the protector is unable to meet the general, mechanical, and optical (if applicable) requirements of the standard.1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. Metric units of measurement in this specification are in accordance with the International System of Units (SI). If a value for measurement as given in this specification is followed by an equivalent value in other units, the first stated is to be regarded as the requirement. A given equivalent value may be approximate.1.7 The following precautionary caveat pertains only to the test methods portions, Sections 9 – 11, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

This specification applies to eye protective devices, designed for use by players of the sport of paintball that minimize or significantly reduce injury to the eye and adnexa due to impact and penetration of paintballs. Field of view, refractive tolerances, astigmatism, power imbalance, prism imbalance, vertical imbalance, horizontal imbalances, luminous transmittance, haze, optical quality, and physical lens defects of the eye protective devices shall be tested to meet the requirements prescribed.1.1 This specification applies to eye, face, and head protective devices, designed for use by players of the sport of paintball, which minimize or significantly reduce injury to the eye, adnexa of eye, face, and head due to paintball impact or penetration, or both.1.2 EHPDs by nature provide three types of protection. The first type of protection is for the eyes and adnexa of eye and not necessarily for any other parts of the face or head. The second type of protection adds coverage for the ears and face. The third type of coverage adds cranial coverage in addition to that provided to types II and III. These coverage types are defined in Section 8.1.3 This specification does not limit the wearing of eyeglasses or contact lenses when used in conjunction with the EHPD.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

This specification covers eye protective devices (EPDs) intended for use in the sport of air soft with 6-mm air soft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of air soft projectiles. This specification also applies to EPDs designed for use by participants in tactical sports using air soft guns. This specification provides guidance with respect to performance, materials of construction and openings, sample preparation, test methods such as optical test methods and mechanical tests, and product marking.1.1 This specification applies to eye protective devices (EPDs) designed for use by participants in the sport of airsoft with 6-mm airsoft projectiles. These EPDs are designed to minimize or significantly reduce injury to the eye and adnexa as a result of impact and penetration of airsoft projectiles.1.2 When airsoft guns are used for target practice with a paper or gel target and a backstop sufficient to prevent ricochet, shooters may wear eye protection (shooting glasses) appropriate for use with firearms, ball bullet (BB) guns or air guns that meet ANSI Z87.1. The balance of this specification applies to EPDs designed for use by participants in tactical sports using airsoft guns.1.3 EPDs meeting the requirements of this specification offer protection to the eyes and adnexa and not necessarily to any other parts of the head.1.4 This specification does not limit the wearing of eyeglasses or contact lenses when used in conjunction with the EPD based on the information provided by the manufacturer in 9.2.21.1.5 Units—The values stated in SI units are to be regarded as the standard. No other units of measurement are included in this standard.1.6 The following information is provided for the laboratory conducting the test for the protection of their personnel: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 646元 加购物车

定价： 590元 加购物车

This specification defines performance requirements for helmets used in nonmotorized recreational snow sports. The hot, cold, and wet helmets shall be subjected to the dynamic strength retention test. The ambient helmet shall be subjected to the positional stability (roll-off) test. Anvils to be used for impact tests in this specification are described as follows: flat anvil, hemispherical anvil, and edge anvil. All impacting shall be performed in accordance with the specified requirements.1.1 This specification defines performance requirements for helmets used in nonmotorized recreational snow sports (such as skiing, snowboarding, and other alpine sports). This specification is a performance standard and is not intended to restrict design. Although a helmet that meets this specification will help reduce the risk of some types of injuries to the head at slower speeds, the protection is limited. The user is responsible for participating in the sport within his/her abilities and the nature of the snow conditions which may vary widely. Compliance with the common sense rules of the sport's safety, including any applicable responsibility codes, is essential to help reduce the risk of personal injury.1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein.1.3 Partial utilization of this specification is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the standard and should not be sold with any indication that it meets parts of the standard.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

This specification delas with the performance requirements for head protection used for training and competition in martial arts such as karate, wushu, and taekwondo, where normal contact between participants may be repeated, but is limited to a level that is not intended to produce injury. These activities typically take place in indoor or outdoor environments where the temperature is moderate. This specification recognizes the desirability of a lightweight and streamlined construction, and ventilation; however it is a performance specification, and is not intended to restrict design. Headgears shall be tested for the following and using the following test methods: reference marking, configuration, materials, projections, vision, retention test, stability or roll-off test, low-energy falling impact test, high-energy falling impact test, low-energy striking impact test, high-energy striking impact test, and high and low speed errors. The apparatus which shall be used are the test headforms, stability test instruments and equipment, falling impact test instruments and equipment, and striking impact instruments and equipment. The significance and use, conditioning environments, and test schedule are also detailed.1.1 This specification covers performance requirements for head protection used for training and competition in combative sports such as karate, wushu, and taekwondo, where normal contact between participants may be repeated, but is limited to a level that is not intended to produce injury. These activities typically take place in indoor or outdoor environments where the temperature is moderate. This specification recognizes the desirability of a lightweight and streamlined construction, and ventilation; however, it is a performance specification, and is not intended to restrict design.1.2 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted in this specification.1.3 Partial utilization of this standard is prohibited. Any statement of compliance with this specification shall be a certification that the product meets all of the requirements of the specification in its entirety. A product that fails to meet any one of the requirements of this specification is considered to have failed the specification, and shall not be distributed or sold with any indication that it meets parts of the specification.1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.5 The following safety caveat applies to the chemical, mechanical, or physical, or a combination thereof, test methods described herein and is meant specifically for those performing the tests (in an effort to provide them with notice to take the appropriate precautions when conducting the tests): This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

定价： 646元 加购物车

定价： 515元 加购物车

定价： 646元 加购物车

1.1 This terminology covers terms related to impact test methods and impact attenuation specifications of sports equipment and surfaces.1.2 This terminology is appropriate for use in the development of standards that describe gravity-driven impact test methods or specify impact attenuation performance criteria and which fall under the jurisdiction of ASTM Committee F08 on Sports Equipment and Facilities.1.3 This terminology defines common terms that are applicable to many sports-related impact tests including those used in the context of sports surfaces, athletic footwear, protective equipment and padding. The use of a common terminology will promote greater consistency among standards and reduce the risk of misinterpretation.1.4 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 加购物车

定价： 515元 加购物车

4.1 This practice may be used to evaluate pertinent performance characteristics of men's and boys' launderable woven dress shirts and sport shirts.4.2 The characteristics to be evaluated and the acceptance criteria assigned to these areas shall be set by mutual agreement between purchaser and supplier.4.3 The uses and significance of specific properties are discussed in the appropriate test methods and performance specifications.1.1 This practice covers the evaluation of specific characteristics of importance in launderable woven dress shirts and sport shirts.1.2 Any launderable woven dress shirt or sport shirt may be evaluated using this practice, but it shall not be construed to be a standard of performance.1.3 This practice may be used by mutual agreement between the purchaser and supplier to establish purchasing specifications.1.4 This practice is not intended to be used in the evaluation of woven dress shirts or sport shirts when drycleaned or hand-washed.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

This specification provides a description of a test method for protective headgear used in horse sports and horseback riding that will measure the ability of the headgear to reduce head acceleration when impacting objects of various shapes. Materials covered by this specification include the pair of appropriate size headform and helmet and the anvils for the impacts tests, which consist of the flat anvil and the equestrian hazard anvil. The helmet shall be conditioned in the following environments: ambient, low temperature, high temperature, and water immersion, and shall be impacted at each of four sites centered on or anywhere above the center of the impact line (two sites on the flat anvil and two sites on the equestrian hazard anvil). Dynamic loading and helmet stability tests shall be performed and shall conform to the requirements specified.1.1 This specification covers minimum performance criteria and describes test methods for protective headgear for use in horse sports and horseback riding.1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification.1.3 All testing and requirements of this specification shall be in accordance with Test Methods F1446, except where noted herein.1.4 The values stated in SI units are to be regarded as the standard.1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车

This specification covers the design and minimum performance criteria, and associated test methods (including apparatuses required for) for body protectors used in horse sports and horseback riding. The body protectors shall meet specified requirements for the material used, protector assembly, extent and form of protective material, attachments, and dimension, sizing, and body coverage. The testing procedures that the body protectors shall go through are shock attenuation test, penetration and deformation test, impact sites test, padding separation test, and closure test. Prior to testing, each body protector should be conditioned in accordance to ambient temperature, low temperature, high temperature, and water immersion.1.1 This specification covers minimum performance criteria and describes test methods for body protectors for use in horse sports and horseback riding.1.2 It is not the intention of this specification to bar from consideration materials of improved quality or performance not known at the time of development of this specification.1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 加购物车