定价： 481元 / 折扣价： 409 元 加购物车

定价： 345元 / 折扣价： 294 元 加购物车

This specification covers double pour, centrifugally cast, abrasion-resistant roll shells for general application. The outer layer is white iron and the inner layer is gray iron and there shall be no gradient of mottled iron these layers. Both the white and the gray irons may be melted by any suitable melting process. The white iron portion of the casting shall be produced by chemistry rather than chilling. A chemical analysis of the white and gray irons shall be taken and the chemical compositions shall be controlled to obtain the required mechanical properties. The white iron (Types I, II, III, and IV) shall conform to the specified Brinell hardness and the gray iron (Class Nos. 20, 25, 30, and 35) shall conform to the specified tensile strength. The minimum thickness of the white iron layer is given. Hardness and tension tests of the cast dual metal shall be performed.1.1 This specification covers double pour, centrifugally cast, abrasion-resistant roll shells for general application. The outer layer is white iron and the inner layer is gray iron. There shall be no gradient of mottled iron between the white iron and the gray iron.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.2.1 Within the text, the SI units are shown in brackets.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 The nitrogen content as determined by this test method is normally considered to be related to the amount of hide substance (protein fiber) present in the leather sample. A factor of 5.62 is normally used to calculate the hide substance from the nitrogen content.4.1.1 The 5.62 factor represents the average result of many analyses of animal hides, but it cannot be considered to be accurate since it varies somewhat from hide to hide of the same type, from type of hide to type of hide, and also with the thickness of hide retained in the final leather (split thickness as compared to original hide thickness). As a result of these variations, the true factor for any given leather may be expected to vary from 5.44 to 5.80 or about ±3 %.34.2 A given leather sample may contain nitrogenous substances other than hide substance (protein fiber) which will be analyzed for by this test method, such as resins, dyestuffs, etc., that contain nitrogen. Therefore, although this test method is fairly accurate for determining the nitrogen content of leather, its use for determining hide substance may result in large errors.4.3 The hide substance value derived from this determination has a large bearing on other chemical determinations of a given leather. Any errors, such as those described in 4.1.1 and 4.2, will be carried over into these other analytical calculations.1.1 This test method covers the determination of the nitrogen content of all types of leather, wet blue and wet white. The nitrogen content is used to calculate the hide substance (protein fiber) content of leather, wet blue and wet white.NOTE 1: The original test method for leather was essentially a composite of Method 6441 of Federal Test Method Standard No. 311 and Method B5 of the American Leather Chemists Association.NOTE 2: Melamine, if present in bonded leather, could give an artificially high value for the calculation of protein fiber.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers centrifugally cast cylinders with an outer layer of white cast iron and the remainder of the material of gray cast iron. These castings are suitable for pressure containing parts of the design strength of which is based on the gray iron portion of the cylinder. The white iron portion of the cylinder shall be made to a minimum hardness and the casting process shall be controlled to produce a metallurgical bond between the two metal layers. All surfaces shall be machined prior to the cylinders being placed into service. The tensile strength of the cast irons shall be measured by tension testing while the thickness of the white cast iron shall be determined by ultrasonic testing.1.1 This specification2 covers centrifugally cast cylinders with an outer layer of white cast iron and the remainder of the material of gray cast iron. These castings are suitable for pressure-containing parts, the design strength of which is based on the gray iron portion of the cylinder. These castings are suitable for service at temperatures up to 450 °F [230 °C].1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.1.3 The following safety hazards caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

6.1 The environmental chamber method is an accelerated test for determining the resistance of Wet Blue and Wet White to the growth of fungi, the causal agent of mold. See Test Method D3273.3,46.2 The environmental chamber method is useful in estimating the performance of fungicides and should assist in the prediction of storage time before fungal growth begins.6.3 The environmental chamber method duplicates the natural environment in which Wet Blue or Wet White is inoculated with fungal spores and subsequently disfigured or discolored by fungi.6.4 The environmental chamber method measures the resistance of the treated Wet Blue or Wet White to the germination of spores and subsequent vegetative growth that spreads over the surface of a comparatively large Wet Blue or Wet White specimen over a period of four weeks.6.5 The environmental chamber can be kept inoculated with fungi representative of those found in tanneries by adding samples of Wet Blue and Wet White with fungal growth from currently operating tanneries.6.6 Control specimens of Wet Blue and Wet White without fungicide treatment can be added to the chamber periodically to increase levels of fungal growth in the chamber.6.7 Leaching of fungicide from the test specimen into the agar often causes a zone of inhibition of fungal growth in the Petri dish test, but in the environmental chamber any leaching of fungicide from the test specimen drips into the water contained in the chamber and thus does not cause the types of false readings observed in the Petri dish test.1.1 This environmental chamber method measures the resistance of the treated Wet Blue and Wet White to the germination of spores and subsequent vegetative growth over a period of four weeks. The test method is useful in estimating the performance of fungicides and should assist in the prediction of storage time of Wet Blue and Wet White before fungal growth begins. The apparatus is designed so it can be easily built or obtained by any interested party and duplicate the natural environment in which Wet Blue and Wet White is inoculated with fungal spores. Spores that germinate on untreated or treated Wet Blue and Wet White can produce fungal growth, resulting in disfigurement or discoloration, or both, of the Wet Blue and Wet White.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

5.1 All commercial reflectometers measure relative reflectance. The instrument reading is the reflectance factor, the ratio of the light reflected by a reference specimen to that reflected by a test specimen. That ratio is dependent on specific instrument parameters.5.2 National standardizing laboratories and some research laboratories measure reflectance on instruments calibrated from basic principles, thereby establishing a scale of absolute reflectance as described in CIE Publication No. 44 (2). These measurements are sufficiently difficult that they are usually left to laboratories that specialize in them.5.3 A standard that has been measured on an absolute scale could be used to transfer that scale to a reflectometer. While such procedures exist, the constraints placed on the mechanical properties restrict the suitability of some optical properties, especially those properties related to the geometric distribution of the reflected light. Thus, reflectance factor standards which are sufficiently rugged and able to be cleaned, depart considerably from the perfect diffuser in the geometric distribution of reflected radiance.5.4 The geometric distribution of reflected radiance from a pressed powder plaque is sufficiently diffuse to provide a dependable calibration of a directional-hemispherical reflectometer. Although pressed powder standards are subject to contamination and breakage, the directional-hemispherical reflectance factor of pressed powder standards can be sufficiently reproducible from specimen to specimen made from a given lot of powder, so as to allow one to assign absolute reflectance factor values to all the powder in a lot.5.5 This practice describes how to prepare white reflectance factor standards from a powder in a manner that allows a standardizing laboratory to assign the absolute scale of reflectance to the plaque.NOTE 1: The collar and receptacle should be securely held in place before pressing the powder.1.1 This practice covers procedures for preparing pressed powder transfer standards. These standards can be used in the near-ultraviolet, visible and near-infrared region of the electromagnetic spectrum. Procedures for calibrating the reflectance factor of materials on an absolute basis are contained in CIE Publication No. 44 (2). Pressed powder standards are used as transfer standards for such calibrations because they have a high reflectance factor that is nearly constant with wavelength, and because the geometric distribution of reflected flux resembles that from the perfect reflecting diffuser.1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 590元 / 折扣价： 502 元 加购物车

This specification covers fiber or fabric reinforced nonvulcanized white polymeric sheet made from polyisobutylene (PIB) intended for use as a single-ply roof membrane exposed to the weather. In-place roof systems design criteria such as fire resistance, field seaming strength, impact/puncture resistance, material compatibility, and uplift resistance, among others, are beyond the scope of this specification. Backed sheets shall conform to the following physical properties: thickness; breaking strength; elongation; tearing strength; low temperature bend; linear dimensional change; fabric adhesion; hydrostatic resistance; ozone resistance; and weather resistance. On the other hand, coating portions on the weather side of the sheet containing no backing shall adhere to the following physical properties: tensile strength; elongation; tear resistance; ozone resistance; and water absorption.1.1 This specification covers white reinforced non-vulcanized polymeric sheet made from polyisobutylene (PIB) intended for use as a single-ply roof membrane exposed to the weather. The sheet shall be reinforced with fiber or fabric.1.1.1 The polymers used in these sheets have thermoplastic characteristics at time of installation.1.2 The tests and property limits used to characterize these sheets are minimum values.1.2.1 In-place roof systems design criteria such as fire resistance, field seaming strength, impact/puncture resistance, material compatibility, and uplift resistance, among others, are factors that must be considered, but are beyond the scope of this specification.The following precautionary caveat pertains to the test methods portion only, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

定价： 0元 / 折扣价： 0 元

This test method details the standard procedure for determining the porosity of white or near white mineral spirits insoluble paint film by staining to indicate the degree to which a subsequent coat will penetrate. This test method shall require the use of film applicators, reflectometer, vacuum drawdown plate, camelhair brush, plastic wash bottle, test panel, penetrating medium, and filter paper. The test paint is applied to a nonporous surface, air dried, then measured for reflectance. A special colored penetrating medium is applied, the excess removed in a specified manner, and reflectance measured again. The difference between the two readings indicates the degree of porosity; the smaller the difference, the lower the porosity of the film and the greater its ability to resist penetration.1.1 This test method covers the determination of the porosity of a white or near white mineral spirits insoluble paint film to indicate the degree to which a subsequent coat will penetrate.1.2 The texture of the film can affect cleanup that will influence the results of the test. A stain applied to a high-hiding paint will not lower the reflectance as much as the same stain applied to a low-hiding paint of equal porosity. These points must be considered in comparing different paints.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

3.1 These test methods are suitable for determining the level of purity and for determining the levels of various impurities. They may be used to establish compliance with specification requirements.1.1 These test methods cover procedures for the chemical analysis of basic carbonate white lead and basic sulfate white lead.NOTE 1: If it is necessary to separate these pigments from others, refer to Practice D215.1.2 The analytical procedures appear in the following order:  Section Preparation of Sample  6Basic Carbonate White Lead:   Small Amounts of Iron  7 Total Lead  8 Moisture and Other Volatile Matter  9 Carbon Dioxide (Evolution Method) 10 Carbon Dioxide and Combined Water (Combustion Method) 11 Lead Carbonate 12 Total Matter Insoluble in Acetic Acid 13 Total Matter Insoluble in Acid Ammonium Acetate 14 Total Impurities Other Than Moisture 15 Coarse Particles 16Basic Sulfate White Lead:   Small Amounts of Iron 17 Total Lead   Moisture and Other Volatile Matter 19 Total Sulfate 20 Zinc Oxide 21 Basic Lead Oxide 22 Total Impurities 23 Coarse Particles 241.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

1.1 This practice covers the chemical analysis of the usual white linseed oil paints. The methods included are listed in Table 1.1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

定价： 0元 / 折扣价： 0 元

This specification covers basic carbonate white lead used as a pigment and in putty. The pigments may be in dry form or a paste in oil. Dry pigment shall conform to the required contents of lead carbonate, moisture and other volatile matter, impurities, and coarse particles. Paste in oil and semipaste containing volatile thinner shall also conform to the requirements of pigment, linseed oil, moisture and other volatile matter, and coarse particles and skins of dry pigment. Tests for the following shall be done: coarse particles; moisture in pigment; lead carbonate and total other impurities; and pigment, linseed oil, and moisture and other volatile matter in paste in oil.1.1 This specification covers the material commercially known as basic carbonate white lead, used as a pigment and in putty. The pigment may be purchased in the dry form or as a paste in oil.1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

4.1 White zinc pigments find considerable use in white paints, and as such it is useful to formulators and users to be able to monitor the amounts of these pigments in whole paints. It is also of interest to raw material suppliers and paint producers to check the specifications of each pigment.1.1 These test methods cover procedures for the analysis of white zinc pigments.1.2 The analytical procedures appear in the following order:  SectionPreparation of Sample  6 Zinc OxideTotal Zinc, Using Diphenylamine as Internal Indicator  7 Total Zinc, Using Uranyl Acetate as External Indicator  8 Total Impurities  9 Total Sulfur 10Moisture and Other Volatile Matter 11Leaded Zinc OxideTotal Lead 12Total Zinc 13Total Sulfur 14Total Impurities 15Moisture and Other Volatile Matter 16Water-Soluble Salts 17Zinc SulfideZinc Oxide 18Zinc Sulfide 19Water-Soluble Salts 20Moisture and Other Volatile Matter 21Barium Sulfate 22Titanium Dioxide 231.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车

4.1 This test method is used as a referee method and for quality control. The vehicle (oil) for preparing the dispersions and the tinting pigment (ultramarine blue) are specified but other vehicles and tinting pigments can be used. Any such changes in the test method must be agreed upon between the purchaser and the seller.4.2 The results obtained with a muller do not necessarily agree with an industrial situation where different dispersing conditions exist. However, dispersing with a muller is a fast and relatively inexpensive way of testing tinting strength for routine quality control.1.1 This test method describes the procedure for determining the relative tinting strength of white pigments by visual assessment of blue tints.1.2 This test method is applicable only for comparing the test pigment with a reference standard of the same type and grade.NOTE 1: Test Method D2745 describes a procedure for instrumental evaluation of black tinted samples.1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 515元 / 折扣价： 438 元 加购物车

AbstractThese test methods cover procedures for the chemical analysis of white titanium dioxide pigments. The analytical procedures appear in the following order: sample preparation, qualitative analysis, moisture content determination, total titanium content determination by Jones Reductor and Aluminum Reduction methods, aluminum oxide content determination, and silica content determination. The reagents to be used shall include ammonium hydroxide, ammonium sulfate, hydrochloric acid, hydrogen peroxide, hydrogen sulfide, sulfuric acid, tartaric acid, tin, zinc, carbon steel, iron, ferric sulfate solution, nitric acid, sodium oxalate, potassium permanganate, aluminum metal foil, ammonium thiocyanate indicator solution, ferritic ammonium sulfate solution, sodium bicarbonate solution, sulfuric acid, titanium dioxide, acetic acid, ammonium phosphate, EDTA solution, methyl orange indicator solution, sodium bisulfate monohydrate, sodium fluoride, xylenol orange indicator solution, and zinc sulfate solution.1.1 These test methods cover procedures for the chemical analysis of white titanium dioxide pigments.1.2 The analytical procedures appear in the following order:  SectionsPreparation of Sample 4Qualitative Analysis 5 and 6Moisture 7Total Titanium:   Jones Reductor Method   8 – 12 Aluminum Reduction Method 13 – 17Aluminum Oxide 18 – 22Silica 23 – 291.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A specific hazard statement is given in Section 19.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

定价： 590元 / 折扣价： 502 元 加购物车