
【国外标准】 Standard Test Method for Ferrous Debris Quantification
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
5.1 By quantifying the concentration of total ferrous debris, this test method provides a direct indication of wear in the machinery by enabling the user to pinpoint when there is a deviation from the normal buildup of ferrous debris shed by the machinery or when the concentration of ferrous debris has exceeded safe operating limits. Specific guidance regarding such procedures may be found in Guides D7669, D7720, and D7874.5.2 This test method can be performed on-site and can be utilized as a particle-size insensitive, minimum sample preparation alternative to laboratory-based screening for abnormal machinery conditions due to the presence of wear debris by means of ferrography as described in Practice D7690, or elemental analysis methods such as atomic emission spectrometry, described in Test Methods D5185 and D6595.1.1 This test method describes a means for quantitative determination of the concentration of ferrous debris in lubricants and greases.1.2 This test method provides a determination of the concentration of ferrous debris in the lubricant or grease from a nominal 0 mg/kg to 10 000 mg/kg (1 % by mass) or greater.1.3 This test method is applicable to all types of lubricating fluids (API Group I-V) and greases sampled from machinery and other mechanical equipment, including reciprocating engine oils, turbine oils, hydraulic oils, gear oils, and bearing greases.1.4 This test method describes a means by which a sample of lubricant or grease is placed in a magnetometer apparatus, which determines the concentration of ferrous debris and provides these readings directly to the operator without further calculation.1.5 This test method is applicable to in-service lubricants and greases at any stage of degradation.1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM D8120-17
标准名称:
Standard Test Method for Ferrous Debris Quantification
英文名称:
Standard Test Method for Ferrous Debris Quantification标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM E3168-20a Standard Practice for Determining Low-Contrast Visual Acuity of Radiographic Interpreters
- ASTM E317-21 Standard Practice for Evaluating Performance Characteristics of Ultrasonic Pulse-Echo Testing Instruments and Systems without the Use of Electronic Measurement Instruments
- ASTM E3170/E3170M-18(2023) Standard Practice for Phased Array Ultrasonic Testing of Polyethylene Electrofusion Joints
- ASTM E3171-21a Standard Test Method for Determination of Total Silver in Textiles by ICP-OES or ICP-MS Analysis
- ASTM E3178-18 Standard Practice for Evaluating Static and Cidal Chemical Decontaminants against Bacillus Spores using Centrifugal Filtration Tubes
- ASTM E3182-20 Standard Practice for Preparing an Occupant Exposure Screening Report (OESR) for Substances in Installed Building Products
- ASTM E3186-19 Standard Guide for Use and Testing of Dry-Block Temperature Calibrators
- ASTM E3191-18 Standard Specification for Permanent Foaming Fixatives Used to Mitigate Spread of Radioactive Contamination
- ASTM E3192/E3192M-20 Standard Practice for Soft Armor Conditioning by Tumbling
- ASTM E3197-23 Standard Terminology Relating to Examination of Fire Debris
- ASTM E3199-22a Standard Guide for Alternative Allocation Approaches to Modeling Input and Output Flows of Secondary Materials and Related Recycling Scenarios in Life Cycle Assessment
- ASTM E3200-21 Standard Guide for Investment Analysis in Environmentally Sustainable Manufacturing
- ASTM E3208-20 Standard Specification for Minimum Equipment Requirements for Mobile Surface Contaminant Classification and Measurement Equipment
- ASTM E3209/E3209M-20 Standard Test Method for Pavement Thickness by Magnetic Pulse Induction
- ASTM E321-20 Standard Test Method for Atom Percent Fission in Uranium and Plutonium Fuel (Neodymium-148 Method)