【国外标准】 Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials

本网站发布时间： 2024-02-28

ASTM D6865-17
Active
定价：590元
加购物车
在线阅读

开通会员免费在线看70000余条国内标准，赠送文本下载次数，单本最低仅合13.3元！还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权！查看详情>>

标准简介

适用范围：

This specification covers acrylonitrile-styrene-acrylate (ASA) and acrylonitrile-EPDM-styrene (AES) plastics and alloys suitable for injection molding and extrusion. ASA and AES materials, and ASA and AES alloys are classified into groups according to their composition. These groups are subdivided into classes and grades: class 0, 1, 2, and 3; grade 0, 1, 2, 3, 4, and 5. The tensile stresses at yield, modulus of elasticity in tension, charpy impact strength, vicat softening temperature, and melt volume-flow rate shall be tested to meet the requirements prescribed.1.1 This classification system covers ASA and AES materials, and ASA and AES alloys suitable for injection molding and extrusion. This classification system does not cover recycled ASA and AES materials, and recycled ASA and AES alloys.1.2 The properties included in this standard are those required to identify the compositions covered. Other requirements necessary to identify particular characteristics important to specialized applications are to be specified by using the suffixes as given in Section 5.1.3 This classification system and subsequent line callout (specification) are intended to provide a means of calling out plastic materials used in the fabrication of end items or parts. It is not intended for the selection of materials. Material selection can be made by those having expertise in the plastic field only after careful consideration of the design and the performance required of the part, the environment to which it will be exposed, the fabrication process to be employed, the costs involved, and the inherent properties of the material other than those covered by this standard.1.4 The following precautionary caveat pertains only to the test method portion, Section 11, of this classification system: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.NOTE 1: This classification system and ISO 6402 and ISO 19065 address the same subject matter but differ in technical content.

基本信息

标准号：
ASTM D6865-17
标准名称：
Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials
英文名称：
Standard Classification System and Basis for Specifications for Acrylonitrile–Styrene–Acrylate (ASA) and Acrylonitrile–EPDM–Styrene (AES) Plastics and Alloys Molding and Extrusion Materials
标准状态：
Active
发布日期：
实施日期：
出版语种：

标准分类号

标准ICS号：
83.080.20
中标分类号：

关联标准

替代以下标准：
被以下标准替代：
引用标准：
采用标准：

出版信息

页数：
5 页
字数：
开本：

其他信息

起草人：
起草单位：
归口单位：
D20.15
提出部门：
发布部门：

其它标准

推荐标准