
【国外标准】 Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic pipe and fittings. The steel reinforced, spirally formed thermoplastic pipes are intended for use in underground applications where soil provides support for their flexible walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial waste applications and drainage pipes. The pipe dimensions, pipe stiffness, flattening, impact resistance, tensile strength of seam, and joint tightness shall be tested to meet the requirements prescribed.1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, impact resistance, pipe stiffness, flattening, buckling, tensile strength of seam, joint systems, perforations, and markings for steel reinforced thermoplastic pipe and fittings of nominal sizes 8 in. [200 mm] through 120 in. [3000 mm]. The steel reinforced, spirally formed thermoplastic pipes governed by this standard are intended for use in underground applications where soil provides support for their flexible walls. These pipes will be used for gravity flow and non-pressure applications, such as storm sewers, sanitary sewers, industrial waste applications and drainage pipes.1.2 Units—The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text the SI units are shown in brackets. The values stated in each system may not be exact equivalents: therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 There is no similar or equivalent ISO standard.1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM F2562/F2562M-15(2019)
标准名称:
Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage
英文名称:
Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- AS 2562-1982 Hydrometers - Portable syringe-type for lead-acid batteries
- AS 2805.6.1.1-2009 (R2019)/Amdt 1-2011 Electronic funds transfer - Requirements for interfaces Key management - Principles
- AS 3565.4-2007 (R2019)/Amdt 1-2010 Meters for water supply In-service compliance testing
- AS 3730.15-1991 Guide to the properties of paints for buildings Primer - Latex - For metallic zinc surfaces
- AS 4276.15:2014 Water microbiology Examination for Vibrio cholerae
- AS 5013.15-2004 Food microbiology Microbiology - General guidance for enumeration of presumptive Escherichia coli - Most probable number technique
- AS IEC 60300.3.15-2011 Dependability management Application guide - Engineering of system dependability
- AS ISO 14520.15-2009 Gaseous fire-extinguishing systems - Physical properties and system design IG-541 extinguishant (ISO 14520-15:2005, MOD)
- AS/NZS 3200.2.15:1994 Approval and test specification - Medical electrical equipment Particular requirements for safety - Capacitor discharge X-ray generators
- AS/NZS 3350.2.15:1997 Safety of household and similar electrical appliances Particular requirements - Appliances for heating liquids
- AS/NZS 3350.2.15:1997/Amdt 1:1997 Safety of household and similar electrical appliances - Particular requirements - Appliances for heating liquids
- AS/NZS 3350.2.15:1997/Amdt 3:2001 Safety of household and similar electrical appliances - Particular requirements - Appliances for heating liquids
- AS/NZS 3350.2.15:1997/Amdt 4:2001 Safety of household and similar electrical appliances - Particular requirements - Appliances for heating liquids
- AS/NZS 3350.2.15:2002/Amdt 1:2003 Safety of household and similar electrical appliances Particular requirements for appliances for heating liquids (IEC 60335-2-15:1995, MOD)
- AS/NZS 3350.2.15:2002/Amdt 2:2003 Safety of household and similar electrical appliances - Particular requirements for appliances for heating liquids (IEC 60335-2-15:1995, MOD)