
【国外标准】 Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
本网站 发布时间:
2024-02-28
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>

适用范围:
3.1 This test method provides a means of assessing the sulfate resistance of mortars made using portland cement, blends of portland cement with pozzolans or slags, and blended hydraulic cements. Test Method C452 is suitable for evaluating portland cements but not blended cements or blends of portland cement with pozzolans or slags.3.2 The standard exposure solution used in this test method, unless otherwise directed, contains 352 moles of Na2SO4 per m3 (50 g/L). Other sulfate concentrations or other sulfates such as MgSO4 may be used to simulate the environmental exposure of interest. Further discussion of these and other technical issues is given in the Appendix.1.1 This test method covers the determination of length change of mortar bars immersed in a sulfate solution. Mortar bars made using mortar described in Test Method C109/C109M are cured until they attain a compressive strength of 20.0 ± 1.0 MPa [3000 ± 150 psi], as measured using cubes made of the same mortar, before the bars are immersed.1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
标准号:
ASTM C1012/C1012M-18b
标准名称:
Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
英文名称:
Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution标准状态:
Active-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- ASTM D1780-05(2020) Standard Practice for Conducting Creep Tests of Metal-to-Metal Adhesives
- ASTM D1786-21 Standard Specification for Toluene Diisocyanate
- ASTM D1790-21 Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact
- ASTM D1792-17(2023) Standard Test Method for Long-Term Removability Properties of Emulsion Floor Polishes
- ASTM D1793-23 Standard Test Method for Water Spotting of Emulsion Floor Polishes
- ASTM D1813-13(2023) Standard Test Method for Measuring Thickness of Leather Test Specimens
- ASTM D1814-70(2021) Standard Test Method for Measuring Thickness of Leather Units
- ASTM D1817-05(2021) Standard Test Method for Rubber Chemicals—Density
- ASTM D1824-16 Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates
- ASTM D1826-94(2017) Standard Test Method for Calorific (Heating) Value of Gases in Natural Gas Range by Continuous Recording Calorimeter
- ASTM D1828-01(2021) Standard Practice for Atmospheric Exposure of Adhesive-Bonded Joints and Structures
- ASTM D1830-17 Standard Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method
- ASTM D1835-22 Standard Specification for Liquefied Petroleum (LP) Gases
- ASTM D1844-86(2020) Standard Test Methods for Chemical Analysis of Basic Lead Silicochromate
- ASTM D1845-86(2020) Standard Test Methods for Chemical Analysis of Strontium Chromate Pigment