【国外标准】 Standard Practice for Calibration of an Airborne Particle Counter Using Monodisperse Spherical Particles (Withdrawn 2007)
本网站 发布时间:
2024-02-28
- ASTM F328-98(2003)
- Withdrawn, No replacement
- 定价: 0元 / 折扣价: 0 元
- 在线阅读
开通会员免费在线看70000余条国内标准,赠送文本下载次数,单本最低仅合13.3元!还可享标准出版进度查询、定制跟踪推送、标准查新等超多特权!  
查看详情>>
标准简介
适用范围:
1.1 This practice covers procedures for calibrating and determining performance of an optical discrete airborne particle counter (DAPC) when presented with a challenge aerosol of near-monodisperse spherical particles. The practice is directed towards determination of accuracy and resolution of the DAPC for particles which have entered the sampling inlet of the DAPC. Consideration of inlet sampling efficiency is not part of this practice.1.2 The procedures covered here include inlet sample flow rate, zero count level, particle sizing accuracy, particle sizing resolution, particle counting efficiency, and particle concentration limit.1.3 The particle size parameter that is reported is the equivalent optical diameter based on projected area of a particle of known refractive index which is suspended in air. The minimum diameter that can be reported by a DAPC is normally specified by the manufacturer and the maximum diameter that can be reported for a single sample is determined by the dynamic range of the DAPC being used. Typical minimum diameters are in the range from approximately 0.05 m to 0.5 m and a typical dynamic range specification will be between 10 to 1 and 50 to 1.1.4 The counting rate capability of the DAPC is limited by temporal coincidence for the specific instrument and by the maximum counting rate capability of the electronic sizing and counting circuitry. Coincidence is defined as the simultaneous presence of more than one particle within the DAPC optically defined sensing zone at any time. The coincidence limit is a statistical function of the airborne particle concentration and the sensing zone volume (1). This limitation may be modified by the presence of particles with dimension so large as to be a significant fraction of the sensing zone dimension (2). The saturation level or maximum counting rate of the electronic counting circuitry shall be specified by the manufacturer and is always greater than the DAPC counting rate for the challenge aerosol used for any portion of this practice.1.5 Calibration in accordance with all parts of this practice may not be required for routine field calibration of a DAPC unless significant changes have been noted in operation of the DAPC or major DAPC component repairs or replacements have been made. In that situation, the DAPC should be taken to a suitable metrology facility for complete calibration, following necessary repairs or modifications. Normally, the routine field calibration may consist of determination of inlet flow rate, zero count level, and particle sizing accuracy. The DAPC functions to be calibrated shall be field or metrology facility calibrations shall be determined by agreement between purchaser and user, but shall not exceed 12 months, unless DAPC stability for longer periods is verified by measurements in accordance with this practice.1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
标准号:
ASTM F328-98(2003)
标准名称:
Standard Practice for Calibration of an Airborne Particle Counter Using Monodisperse Spherical Particles (Withdrawn 2007)
英文名称:
Standard Practice for Calibration of an Airborne Particle Counter Using Monodisperse Spherical Particles (Withdrawn 2007)标准状态:
Withdrawn, No replacement-
发布日期:
-
实施日期:
出版语种:
- 推荐标准
- 国家标准计划
- BS ISO 5501-2:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-3:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 5501-1:2024 Tobacco heating systems. Definitions and standard conditions for aerosol generation and collection
- BS ISO 24138:2024 Information and documentation. International Standard Content Code (ISCC)
- 24/30492859 DC BS EN IEC 61753-1 Fibre optic interconnecting devices and passive components - Performance standard
- BS EN IEC 61753-071-02:2020+A1:2024 Fibre optic interconnecting devices and passive components. Performance standard
- 24/30491443 DC standard
- KS D ISO 9226 금속 및 합금의 부식-대기의 부식성-부식성 평가를 위한 표준 시험편의 부식 속도 결정
- KS B 0831 비파괴검사 — 초음파탐상검사 — 표준 시험편
- 24/30489392 DC BS EN IEC 62358 Ferrite cores. Standard inductance factor for gapped cores and its tolerance
- BS ISO 19848:2024 - TC Tracked Changes. Ships and marine technology. Standard data for shipboard machinery and equipment
- BS ISO 19848:2024 Ships and marine technology. Standard data for shipboard machinery and equipment
- BS IEC 61360-7:2024 Standard data element types with associated classification scheme
- 24/30487130 DC BS EN 50566:2017/A2:2024 Product standard to demonstrate the compliance of wireless communication
- 24/30486472 DC - Product standard